# This document describes Moonraker's full configuration. As this file references configuration for both Klipper (`printer.cfg`) and Moonraker (`moonraker.conf`), each example contains a commment indicating which configuration file is being refrenenced. A basic [sample configuration](./moonraker.conf) in the `docs` directory. ## Core Components Moonraker's core components are always loaded regardless of configuration. ### `[server]` The `[server]` section provides essential configuration for Moonraker. This section is requrired. ```ini # moonraker.conf [server] host: 0.0.0.0 # The host address in which to bind the HTTP server. Default is to bind # to all interfaces port: 7125 # The port the HTTP server will listen on. Default is 7125 ssl_port: 7130 # The port to listen on for SSL (HTTPS) connections. Note that the HTTPS # server will only be started of the certificate and key options outlined # below are provied. The default is 7130. ssl_certificate_path: # The path to a self signed ssl certificate. The default is no path, which # disables HTTPS. ssl_key_path: # The path to the private key used to signed the certificate. The default # is no path, which disables HTTPS. klippy_uds_address: /tmp/klippy_uds # The address of Unix Domain Socket used to communicate with Klippy. Default # is /tmp/klippy_uds max_upload_size: 1024 # The maximum size allowed for a file upload (in MiB). Default is 1024 MiB. enable_debug_logging: False # When set to True Moonraker will log in verbose mode. During this stage # of development the default is False. ``` ### `[file_manager]` The `file_manager` section provides configuration for Moonraker's file management functionality. If omitted defaults will be used. ```ini # moonraker.conf config_path: # The path to a directory where configuration files are located. This # directory may contain Klipper config files (printer.cfg) or Moonraker # config files (moonraker.conf). Clients may also write their own config # files to this directory. Note that this may not be the system root # (ie: "/") and moonraker must have read and write access permissions # for this directory. log_path: # An optional path to a directory where log files are located. Users may # configure various applications to store logs here and Moonraker will serve # them at "/server/files/logs/*". The default is no log paths. queue_gcode_uploads: False # When set to True the file manager will add uploads to the job_queue when # the `start_print` flag has been set. The default if False. enable_object_processing: False # When set to True gcode files will be run through a "preprocessor" # during metdata extraction if object tags are detected. This preprocessor # replaces object tags with G-Code commands compatible with Klipper's # "cancel object" functionality. Note that this process is file I/O intensive, # it is not recommended for usage on low resource SBCs such as a Pi Zero. # The default is False. ``` !!! Note It is also possible to enable object processing directly in the slicer. See the [preprocess-cancellation](https://github.com/kageurufu/cancelobject-preprocessor) documentation for details. ### `[machine]` The `machine` section provides configuration for Moonraker's machine component, which is responsible for for collecting "machine" (ie: PC, SBC, etc) data and communicating with system services such as systemd. ```ini # moonraker.conf [machine] provider: systemd_dbus # The provider implementation used to collect system service information # and run service actions (ie: start, restart, stop). This can be "none", # "systemd_dbus", or "systemd_cli". If the provider is set to "none" service # action APIs will be disabled. The default is systemd_dbus. ``` !!! Note See the [install documentation](installation.md#policykit-permissions) for details on PolicyKit permissions when using the DBus provider. !!! Warning Some distributions (ie: DietPi) disable and mask the `systemd-logind` service. This service is necessary for the DBus provider to issue `reboot` and `shutdown` commands. In this scenario, Moonraker will fall back to CLI based `reboot` and `shutdown` commands. These commands require that Moonraker be able to run `sudo` commands without a password. Alternatively it may be possible to enable the `systemd-logind` service, consult with your distro's documentation. ### `[database]` The `database` section provides configuration for Moonraker's lmdb database. If omitted defaults will be used. ```ini moonraker.conf database_path: ~/.moonraker_database # The path to the folder that stores Moonraker's lmdb database files. # It is NOT recommended to place this file in a location that is served by # Moonraker (such as the "config_path" or the location where gcode # files are stored). If the folder does not exist an attempt will be made # to create it. The default is ~/.moonraker_database. enable_database_debug: False # For developer use only. End users should leave this option set to False. ``` ### `[data_store]` The `data_store` section provides configuration for Moonraker's volatile data store. Note that this is different from the `database`, as it stores data in memory and does not persist between restarts. If omitted defaults will be used. ```ini # moonraker.conf temperature_store_size: 1200 # The maximum number of temperature values to store for each sensor. Note # that this value also applies to the "target", "power", and "fan_speed" # if the sensor reports them. The default is 1200, which is enough to # store approximately 20 minutes of data at one value per second. gcode_store_size: 1000 # The maximum number "gcode lines" to store. The default is 1000. ``` ### `[job_queue]` The `job_queue` section provides configuration for Moonraker's gcode job queuing. If omitted defaults will be used. ```ini # moonraker.conf load_on_startup: False # When set to true the job queue will attempt to load the next # pending job when Klipper reports as "Ready". If the queue has # been paused it will automatically resume. Note that neither # the job_transition_delay nor the job_transition_gcode are # applied in this case. The default is False. automatic_transition: False # When set to True the queue will automatically transition to # the next job in the queue after the current job is complete. # This is useful for belt printers and other machines with the # ability to automate clearing of the build area. When False # the queue will be paused after each job is loaded, requiring # that users manually resume to load the next print. The default # is False. job_transition_delay: # The amount of time to delay after completion of a job before # loading the next job on the queue. The default is no delay. job_transition_gcode: # A gcode to execute after the completion of a job before the next # job is loaded. If a "job_transition_delay" has been configured # this gcode will run after the delay. The default is no gcode. ``` ## Optional Components Optional Components are only loaded if present in `moonraker.conf`. This includes components that may not have any configuration. ### `[authorization]` The `[authorization]` section provides configuration for Moonraker's authorization module. ```ini # moonraker.conf [authorization] login_timeout: # The time, in days, after which a user is forced to re-enter their # credentials to log in. This period begins when a logged out user # first logs in. Successive logins without logging out will not # renew the timeout. The default is 90 days. trusted_clients: 192.168.1.30 192.168.1.0/24 my-printer.lan # A list of newline separated ip addresses, ip ranges, or fully qualified # domain names that are trusted. Trusted clients are given full access to # the API. Both IPv4 and IPv6 addresses and ranges are supported. Ranges # must be expressed in CIDR notation (see http://ip.sb/cidr for more info). # For example, an entry of 192.168.1.0/24 will authorize IPs in the range of # 192.168.1.1 - 192.168.1.254. Note that when specifying IPv4 ranges the # last segment of the ip address must be 0. The default is no clients are # trusted. cors_domains: http://klipper-printer.local http://second-printer.local:7125 # Enables CORS for the specified domains. One may specify * if they wish # to allow all domains, however this should be an option reserved for # client developers and not used in production. A * can also be used # to specify a wildcard that matches several domains. For example: # *.local # http://*.my-domain.com # *.my-domain.com:* # Are all valid entries. However, a wildcard may not be specified in # the top level domain: # http://my-printer.* # The above example will be rejected. # When CORS is enabled by adding an entry to this option, all origins # matching the "trusted_clients" option will have CORS headers set as # well. If this option is not specified then CORS is disabled. force_logins: False # When set to True a user login is required for authorization if at least # one user has been created, overriding the "trusted_clients" configuration. # If no users have been created then trusted client checks will apply. # The default is False. ``` ### `[octoprint_compat]` Enables partial support of Octoprint API is implemented with the purpose of allowing uploading of sliced prints to a moonraker instance. Currently we support Slic3r derivatives and Cura with Cura-Octoprint. ```ini # moonraker.conf [octoprint_compat] enable_ufp: True # When set to True the octoprint_compat module will report that the UFP # plugin is available. If the installed version of Cura supports UFP # files will be uploaded in UFP format. When set to False Cura will # upload files in .gcode format. This setting has no impact on other # slicers. The default is True. flip_h: False # Set the webcam horizontal flip. The default is False. flip_h: False # Set the webcam vertical flip. The default is False. rotate_90: False # Set the webcam rotation by 90 degrees. The default is False. stream_url: /webcam/?action=stream # The URL to use for streaming the webcam. It can be set to an absolute # URL if needed. In order to get the webcam to work in Cura through # an Octoprint connection, you can set this value to # http:///webcam/?action=stream. The default value is # /webcam/?action=stream. webcam_enabled: True # Enables the webcam. The default is True. ``` !!! Tip It is possible to embed "Prusa" style thumbnails in .gcode files using the latest version of Cura. Select `Extensions` -> `Post Processing` -> `Modify G-Code`. In the dialog click the `Add a script` button and select `Create Thumbnail`. Change the width and height (most Moonraker clients handle 300x300 well) then click close. A single large thumbnail is all that is necessary, Moonraker will generate a smaller 32x32 thumbnail from it. This is convenient for users who do not wish to upload in UFP format. ### `[history]` Enables print history tracking. ```ini # moonraker.conf [history] ``` ### `[paneldue]` Enables PanelDue display support. The PanelDue should be connected to the host machine, either via the machine's UART GPIOs or through a USB-TTL converter. Currently PanelDue Firmware Version 1.24 is supported. Other releases may not behave correctly. ```ini # moonraker.conf [paneldue] serial: # The serial port in which the PanelDue is connected. This parameter # must be provided. baud: 57600 # The baud rate to connect at. The default is 57600 baud. machine_name: Klipper # An optional unique machine name which displays on the PanelDue's # Header. The default is "Klipper". macros: LOAD_FILAMENT UNLOAD_FILAMENT PANELDUE_BEEP FREQUENCY=500 DURATION=1 # A list of newline separated "macros" that are displayed in the # PanelDue's "macros" tab. These can be gcode macros or simple # gcodes. A macro may contain parameters. The default is no # macros will be displayed by the PanelDue. confirmed_macros: RESTART FIRMWARE_RESTART # Like the "macros" option, this list is added to the macros tab. # When one of these macros is excuted the PanelDue will prompt # the user with a confirmation dialog. The default is to include # RESTART and FIRMWARE_RESTART. ``` Most options above are self explanatory. The "macros" option can be used to specify commands (either built in or gcode_macros) that will show up in the PanelDue's "macro" menu. Note that buzzing the piezo requires the following gcode_macro in `printer.cfg`: ```ini # printer.cfg [gcode_macro PANELDUE_BEEP] # Beep frequency default_parameter_FREQUENCY: 300 # Beep duration in seconds default_parameter_DURATION: 1. gcode: {action_call_remote_method("paneldue_beep", frequency=FREQUENCY|int, duration=DURATION|float)} ``` ### `[power]` Enables device power control. Multiple "power" devices may be configured, each with their own section, ie: `[power my_printer]`, `[power my_led]`. #### Options common to all power devices The following configuration options are available for all power device types: ```ini # moonraker.conf [power device_name] type: # The type of device. Can be either gpio, klipper_device, rf, # tplink_smartplug, tasmota, shelly, homeseer, homeassistant, loxonev1, # smartthings, or mqtt. # This parameter must be provided. off_when_shutdown: False # If set to True the device will be powered off when Klipper enters # the "shutdown" state. This option applies to all device types. # The default is False. off_when_shutdown_delay: 0 # If "off_when_shutdown" is set, this option specifies the amount of time # (in seconds) to wait before turning the device off. Default is 0 seconds. on_when_upload_queued: False # If set to True the device will power on if the file manager # queues an upload while the device is off. This allows for an automated # "upload, power on, and print" approach directly from the slicer, see # the configuration example below for details. The default is False. locked_while_printing: False # If True, locks the device so that the power cannot be changed while the # printer is printing. This is useful to avert an accidental shutdown to # the printer's power. The default is False. restart_klipper_when_powered: False # If set to True, Moonraker will issue a "FIRMWARE_RESTART" to Klipper # after the device has been powered on. Note: If it isn't possible to # schedule a firmware restart (ie: Klippy is disconnected), the restart # will be postponed until Klippy reconnects and reports that startup is # complete. In this scenario, if Klippy reports that it is "ready", the # FIRMWARE_RESTART will be aborted as unnecessary. # The default is False. restart_delay: 1. # If "restart_klipper_when_powered" is set, this option specifies the amount # of time (in seconds) to delay the restart. Default is 1 second. bound_service: # Can be set to any service Moonraker is authorized to manage with the # exception of the moonraker service itself. See the tip below this section # for details on what services are authorized. When a bound service has # been set the service will be started when the device powers on and stopped # when the device powers off. The default is no service is bound to the # device. ``` !!! Tip Moonraker is authorized to manage the `klipper`, `klipper_mcu`, `webcamd`, `MoonCord`, `KlipperScreen`, and `moonraker-telegram-bot` services. It can also manage multiple instances of a service, ie: `klipper_1`, `klipper_2`. Keep in mind that service names are case sensitive. !!! Note If a device has been bound to the `klipper` service and the `restart_klipper_when_powered` option is set to `True`, the restart will be scheduled to execute after Klipper reports that its startup sequence is complete. #### GPIO Device Configuration The following options are available for `gpio` device types: ```ini # moonraker.conf pin: gpiochip0/gpio26 # The pin to use for GPIO and RF devices. The chip is optional, if left out # then the module will default to gpiochip0. If one wishes to invert # the signal, a "!" may be prefixed to the pin. Valid examples: # gpiochip0/gpio26 # gpio26 # !gpiochip0/gpio26 # !gpio26 # This parameter must be provided for "gpio" type devices initial_state: off # The initial state for GPIO type devices. May be on or # off. When moonraker starts the device will be set to this # state. Default is off. timer: # A time (in seconds) after which the device will power off after being. # switched on. This effectively turns the device into a momentary switch. # This option is available for gpio, klipper_device, tplink_smartplug, # shelly, and tasmota devices. The timer may be a floating point value # for gpio types, it should be an integer for all other types. The # default is no timer is set. ``` Examples: ```ini # moonraker.conf # Control a relay providing power to the printer [power printer] type: gpio pin: gpio26 # uses pin 26 on gpiochip0 off_when_shutdown: True initial_state: off # Control a status led [power printer_led] type: gpio pin: !gpiochip0/gpio16 # inverts pin initial_state: off # Control a printer illumination, powers on when # Moonraker starts [power light_strip] type: gpio pin: gpiochip0/gpio17 initial_state: on ``` #### Klipper Device Configuration The following options are available for `klipper_device` device types: ```ini # moonraker.conf object_name: output_pin my_pin # The Klipper object_name (as defined in your Klipper config). Valid examples: # output_pin my_pin # gcode_macro MY_MACRO # Currently, only `output_pin` and `gcode_macro` Klipper devices are # supported. See the note below for macro restrictions. Keep in mind that # the object name is case sensitive. This parameter must be provided. timer: # A time (in seconds) after which the device will power off after being. # switched on. This effectively turns the device into a momentary switch. # This option is available for gpio, klipper_device, tplink_smartplug, # shelly, and tasmota devices. The timer may be a floating point value # for gpio types, it should be an integer for all other types. The # default is no timer is set. ``` !!! Warning Klipper devices cannot be used to toggle the printer's power supply as they require that Klipper be running and in the "Ready" state. !!! Note Some of the options common to all `[power]` devices are not available for the `klipper_device` type. Specifically `off_when_shutdown` and `restart_klipper_when_powered` may not be configured. The `bound_service` option is restricted, it may not be set to an instance of `klipper` or `klipper_mcu`. ##### Gcode Macro Restrictions To control "gcode_macro" klipper devices, macros must be configured to accept a VALUE parameter, and they must report and update a `value` variable. The value should be 1 when the device is on, and 0 when the device is off. For example, a macro could be configured like the following in `printer.cfg`: ```ini # printer.cfg # Assume we have a neopixel we want to control [neopixel extruder_flare] pin: PA13 [gcode_macro SET_FLARE] # The variable below should be initialized to the startup value. If your # device is configured to be on at startup use "variable_value: 1" variable_value: 0 {% if 'VALUE' not in params %} {action_raise_error("Parameter 'VALUE' missing from 'SET_FLARE'")} {% endif %} {% set state = params.VALUE %} {% if state %} # turn the neopixel on SET_LED LED=extruder_flare RED=0.75 BLUE=0.2 GREEN=0.2 SYNC=0 {% else %} # turn the neopixel off SET_LED LED=extruder_flare RED=0 BLUE=0 GREEN=0 SYNC=0 {% endif %} # Update the state of our variable. This will inform Moonraker that # the device has changed its state. SET_GCODE_VARIABLE MACRO=SET_FLARE VARIABLE=value value={state} ``` This can be controlled via Moonraker with the following in `moonraker.conf`: ```ini # moonraker.conf [power flare] type: klipper_device object_name: gcode_macro SET_FLARE # The option below locks out requests to toggle the flare # when Klipper is printing, however it cannot prevent a # direct call to the SET_FLARE gcode macro. locked_while_printing: True ``` Output Pin Example: ```ini # moonraker.conf # Control a relay providing power to the printer [power my_pin] type: klipper_device object_name: output_pin my_pin ``` !!! Tip If you need to use pwm you can wrap the call to `SET_PIN` in a gcode_macro and configure Moonraker to toggle the Macro rather than the pin directly. #### RF Device Configuration The following options are available for gpio controlled `rf` device types: ```ini # moonraker.conf pin: gpiochip0/gpio26 # The pin to use for GPIO and RF devices. The chip is optional, if left out # then the module will default to gpiochip0. If one wishes to invert # the signal, a "!" may be prefixed to the pin. Valid examples: # gpiochip0/gpio26 # gpio26 # !gpiochip0/gpio26 # !gpio26 # This parameter must be provided for "gpio" type devices initial_state: off # The initial state for GPIO type devices. May be on or # off. When moonraker starts the device will be set to this # state. Default is off. timer: # A time (in seconds) after which the device will power off after being. # switched on. This effectively turns the device into a momentary switch. # This option is available for gpio, klipper_device, tplink_smartplug, # shelly, and tasmota devices. The timer may be a floating point value # for gpio types, it should be an integer for all other types. The # default is no timer is set. on_code: off_code: # Valid binary codes that are sent via the RF transmitter. # For example: 1011. ``` #### TPLink Smartplug Configuration !!! Warning TPLink has removed access to the local API for some of its Kasa devices in recent firmware releases. As such, it is possible that Moonraker will be unable to communicate with your device. While TPLink claims that they will provide a new local API, they have have not done so as of December 22nd, 2021. See [this TPLink forum post](https://community.tp-link.com/en/smart-home/forum/topic/239364) and [this Home Assistant Alert](https://alerts.home-assistant.io/#tplink.markdown) for details. The following options are availble for `tplink_smartplug` device types: ```ini # moonraker.conf address: # A valid ip address or hostname for the tplink device. For example: # 192.168.1.127 # This parameter must be provided. port: # The port to connect to. Default is 9999. # output_id: # For power strips, the socket index to use. Default is 0 which indicates the # device is not a power strip. ``` Example: ```ini # moonraker.conf [power printer_plug] type: tplink_smartplug address: 192.168.1.123 ``` #### Tasmota Configuration The following options are available for `tasmota` device types: ```ini # moonraker.conf # # Note: # If your single-relay Tasmota device switches on/off successfully, # but fails to report its state, ensure that 'SetOption26' is set in # Tasmota. address: # A valid ip address or hostname for the tasmota device. This parameter # must be provided. password: # A password used to authenticate requests. Default is no password. output_id: # The output_id (or relay id) to use if the Tasmota device supports # more than one output. Default is 1. ``` !!! Note This implmentation communicates with Tasmota firmware through its HTTP APIs. It is also possible to use [MQTT](#mqtt-device-configuration) to control devices flashed with Tasmota. Example: ```ini # moonraker.conf [power tasmota_plug] type: tasmota address: 192.168.1.124 password: mypassword ``` #### Shelly Configuration The following options are available for `shelly` device types: ```ini # moonraker.conf address: # A valid ip address or hostname for the shelly device. This parameter # must be provided. user: # A user name to use for request authentication. This option accepts # Jinja2 Templates, see the [secrets] section for details. If no password # is set the the default is no user, otherwise the default is "admin". password: # The password to use for request authentication. This option accepts # Jinja2 Templates, see the [secrets] section for details. The default is no # password. output_id: # The output_id (or relay id) to use if the Shelly device supports # more than one output. Default is 1. ``` !!! Note This implmentation communicates with Shelly firmware through its HTTP APIs. It is also possible to use [MQTT](#mqtt-device-configuration) to control Shelly devices. Example: ```ini # moonraker.conf [power shelly_plug] type: shelly address: 192.168.1.125 user: user2 password: password2 ``` #### Homeseer Configuration The following options are available for `homeseer` device types: ```ini # moonraker.conf address: # A valid ip address or hostname for the homeseer device. This parameter # must be provided. device: # The ID of the device to control. # To find out the ID in the HomeSeer UI, click on the device you want to # control (Make sure to click the sub-device that actually has On/Off # buttons). And then go to the "status/graphics" tab and it should list # "ID" in the "advanced information" section. This parameter must be # provided. user: # The user name for request authentication. This option accepts # Jinja2 Templates, see the [secrets] section for details. This # default is "admin". password: # The password for request authentication. This option accepts # Jinja2 Templates, see the [secrets] section for details. The # default is no password. # ``` #### Home Assistant Configuration (HTTP) The following options are available for `homeassistant` device types: ```ini # moonraker.conf address: # A valid ip address or hostname for the Home Assistant server. This # parameter must be provided. protocol: # The protocol for the URL to the Home Assistant server. Default is http. port: # The port the Home Assistant server is listening on. Default is 8123. device: # The device ID of the switch to control. This parameter must be provided. token: # A token used for request authorization. This option accepts # Jinja2 Templates, see the [secrets] section for details. This paramter # must be provided. domain: # The class of device managed by Home Assistant. Default is "switch". status_delay: 1.0 # The time (in seconds) to delay between requesting a device to turn # on/off and requesting its current status. This is a workaround used # to validate that Home Assistant has successfully toggled the device, # as the API is currently broken on their end. Default is 1 second. # ``` Example: ```ini # moonraker.conf [power homeassistant_switch] type: homeassistant address: 192.168.1.126 port: 8123 device: switch.1234567890abcdefghij token: home-assistant-very-long-token domain: switch ``` #### Loxone Device Configuration The following options are available for `loxone` device types: ```ini # moonraker.conf address: # A valid ip address or hostname for the Loxone server. This # parameter must be provided. user: # The user name used for request authorization. This option accepts # Jinja2 Templates, see the [secrets] section for details. The default is # "admin". password: # The password used for request authorization. This option accepts # Jinja2 Templates, see the [secrets] section for details. The default # is "admin". output_id: # The name of a programmed output, virtual input or virtual # output in the loxone configuration. The default is no output id. # ``` #### MQTT Device Configuration The following options are available for `mqtt` device types: ```ini # moonraker.conf qos: # The MQTT QOS level to use when publishing and subscribing to topics. # The default is to use the setting supplied in the [mqtt] section. command_topic: # The mqtt topic used to publish commands to the device. This parameter must # be provided. command_payload: # The payload sent with the topic. This can be a template, with a "command" # variable included in the template context, where "command" is either "on" # or "off". For example: # {% if command == "on" %} # TURN_ON # {% else %} # TURN_OFF # {% endif %} # The above example would resolve to "TURN_ON" if the request is turn the # the device on, and "TURN_OFF" if the request is to turn the device off. # This parameter must be provided. retain_command_state: # If set to True the retain flag will be set when the command topic is # published. Default is False. state_topic: # The mqtt topic to subscribe to for state updates. This parameter must be # provided. state_response_template: # A template used to parse the payload received with the state topic. A # "payload" variable is provided the template's context. This template # must resolve to "on" or "off". For example: # {% set resp = payload|fromjson %} # {resp["POWER"]} # The above example assumes a json response is received, with a "POWER" field # that set to either "ON" or "OFF". The resolved response will always be # trimmed of whitespace and converted to lowercase. The default is the payload. state_timeout: # The amount of time (in seconds) to wait for the state topic to receive an # update. If the timeout expires the device revert to an "error" state. This # timeout is applied during initialization and after a command has been sent. # The default is 2 seconds. query_topic: # The topic used to query command state. It is expected that the device will # respond by publishing to the "state_topic". This parameter is optional, query_payload: # The payload to send with the query topic. This may be a template or a string. # The default is no payload. query_after_command: # If set to True Moonraker will publish the query topic after publishing the # command topic. This should only be necessary if the device does not publish a # reponse to a command request to the state topic. The default is False. ``` !!! Note Moonraker's MQTT client must be properly configured to add a MQTT device. See the [mqtt](#mqtt) section for details. !!! Tip MQTT is the most robust way of managing networked devices through Moonraker. A well implemented MQTT device will publish all changes in state to the `state_topic`. Moonraker recieves these changes, updates its internal state, and notifies connected clients. This allows for device control outside of Moonraker. Note however that post command actions, such as bound services, will not be run if a device is toggled outside of Moonraker. Example: ```ini # moonraker.conf # Example configuration for ing with Tasmota firmware over mqtt [power mqtt_plug] type: mqtt command_topic: cmnd/tasmota_switch/POWER # Tasmota uses "on" and "off" as the payload, so our template simply renders # the command command_payload: {command} # There is no need to set the retain flag for Tasmota devices. Moonraker # will use the query topic to initalize the device. Tasmota will publish # all changes in state to the state topic. retain_command_state: False # To query a tasmota device we send the command topic without a payload. # Optionally we could send a "?" as the payload. query_topic: cmnd/tasmota_switch/POWER # query_payload: ? state_topic: stat/tasmota_switch/POWER # The response is either "ON" or "OFF". Moonraker will handle converting to # lower case. state_response_template: {payload} # Tasmota updates the state topic when the device state changes, so it is not # not necessary to query after a command query_after_command: False ``` #### SmartThings (HTTP) !!! Important SmartThings Developer API Topics: * See [Getting a Bearer Token](https://developer-preview.smartthings.com/docs/advanced/authorization-and-permissions/) * See [Getting a list of devices](https://developer-preview.smartthings.com/api/public#operation/getDevices) The following options are available for `smartthings` device types: ```ini # moonraker.conf address: api.smartthings.com protocol: https port: 443 token: # A token used for request authorization. This option accepts # Jinja2 Templates, see the [secrets] section for details. This paramter # must be provided. device: # The Device guid of the switch to control. This parameter must be provided. ``` Example: ```ini # moonraker.conf [power smartthings_switch] type: smartthings address: api.smartthings.com protocol: https port: 443 token: smartthings-bearer-token device: smartthings-device-id ``` #### Toggling device state from Klipper It is possible to toggle device power from the Klippy host, this can be done with a gcode_macro, such as: ```ini # printer.cfg [gcode_macro POWER_OFF_PRINTER] gcode: {action_call_remote_method("set_device_power", device="printer", state="off")} ``` The `POWER_OFF_PRINTER` gcode can be run to turn off the "printer" device. This could be used in conjunction with Klipper's idle timeout to turn the printer off when idle with a configuration similar to that of below: ```ini # printer.cfg [delayed_gcode delayed_printer_off] initial_duration: 0. gcode: {% if printer.idle_timeout.state == "Idle" %} POWER_OFF_PRINTER {% endif %} [idle_timeout] gcode: M84 TURN_OFF_HEATERS UPDATE_DELAYED_GCODE ID=delayed_printer_off DURATION=60 ``` #### Power on G-Code Uploads The following is an example configuration that would fully automate the process of powering on a printer and loading a print from a Slicer upload with the "start" flag enabled. ```ini # moonraker.conf # Configure the file manager to queue uploaded files when the "start" flag # is set and Klipper cannot immediately start the print. [file_manager] queue_gcode_uploads: True # Set the config_path and log_path options to the correct locations config_path: log_path: # Configure the Job Queue to start a queued print when Klipper reports as # ready. [job_queue] load_on_startup: True # Configure the job_transition_delay and job_transition_gcode options # if desired. Note that they do no apply to prints loaded on startup. # Configure the "power" device to turn on when uploads are queued. [power printer] type: gpio pin: gpio26 initial_state: off # Power the printer on when the file manager queues an upload on_when_upload_queued: True bound_service: klipper ``` With the above configuration options set, an upload with the "start" flag set to true will be queued. This "printer" device will be notified and powered on. Finally, the job_queue will load and start the queued print after Klipper reports itself as "ready". !!! Note This procedure assumes that the printer is powered off when the gcode file is uploaded. It also assumes that the `job_queue` is empty, if any jobs exist in the queue then the next job on the queue will be loaded. ### `[update_manager]` This enables moonraker's update manager. Note that updates can only be performed on pristine git repos. Repos that have been modified on disk or cloned from unofficial sources are not supported. ```ini # moonraker.conf [update_manager] enable_repo_debug: False # When set to True moonraker will bypass repo validation and allow # updates from unofficial remotes and/or branches. Updates on # detached repos are also allowed. This option is intended for # developers and should not be used on production machines. The # default is False. enable_auto_refresh: False # When set to True Moonraker will attempt to fetch status about # available updates roughly every 24 hours, between 12am-4am. # When set to False Moonraker will only fetch update state on startup # and clients will need to request that Moonraker updates state. The # default is False. refresh_interval: 672 # The interval (in hours) after which the update manager will check # for new updates. This interval is applies to updates for Moonraker, # Klipper, and System Packages, and is the default for all clients. # The default is 672 hours (28 days). enable_system_updates: True # A boolean value that can be used to toggle system package updates. # Currently Moonraker only supports updating packages via APT, so # this option is useful for users that wish to experiment with linux # distros that use other package management applications, or users # that prefer to manage their packages directly. Note that if this # is set to False users will be need to make sure that all system # dependencies are up to date. The default is True. enable_packagekit: True # This option is available when system updates are enabled via the # "enable_system_updates" option. When set to True, system package # updates will be processed via PackageKit over D-Bus. When set to False # the "apt cli" fallback will be used. The default is True. channel: dev # The update channel applied to Klipper and Moonraker. May be 'dev' # which will fetch updates using git, or 'beta' which will fetch # zipped beta releases. Note that this channel does not apply to # client updates, a client's update channel is determined by its # 'type' option. When this option is changed the next "update" will # swap channels, any untracked files in the application's path will be # removed during this process. The default is dev. ``` #### Client Configuration This allows client programs such as Fluidd, KlipperScreen, and Mainsail to be updated in addition to klipper, moonraker, and the system os. Repos that have been modified or cloned from unofficial sources are not supported. Moonraker supports updates for "application" based clients and "web" based clients. Each are detailed separately below. ```ini # moonraker.conf [update_manager client_name] type: web # The client type. For web clients this should be 'web', or 'web_beta'. # The 'web_beta' type will enable updates for releases tagged with # "prerelease" on GitHub. This parameter must be provided. repo: # This is the GitHub repo of the client, in the format of user/client. # For example, this could be set to fluidd-core/fluidd to update Fluidd or # mainsail-crew/mainsail to update Mainsail. This parameter must be provided. path: # The path to the client's files on disk. This parameter must be provided. persistent_files: # A list of newline separated file names that should persist between # updates. This is useful for static configuration files, or perhaps # themes. The default is no persistent files. refresh_interval: # This overrides the refresh_interval set in the primary [update_manager] # section. info_tags: # Optional information tags about this application that are reported to # clients as a list of strings. Each tag should be separated by a new line. # For example: # info_tags: # desc=My Client App # action=webcam_restart # Clients my use these tags to perform additonal actions or display # information, see your client documentation for details on configuration. # The default is an empty list. ``` This second example is for "applications". These may be git repositories or zipped distributions. Note that git repos must have at least one tag for Moonraker to identify its version. ```ini # moonraker.conf # service_name must be the name of the systemd service [update_manager service_name] type: git_repo # Can be git_repo, zip, or zip_beta. See your the client's documentation # for recommendations on which value to use. Generally a git_repo is # an applications "dev" channel, zip_beta is its "beta" channel, and zip # is its "stable" channel. This parameter must be provided. path: # The absolute path to the client's files on disk. This parameter must be # provided. # Example: # path: ~/service_name origin: # The full git URL of the "origin" remote for the repository. This can # be be viewed by navigating to your repository and running: # git remote -v # This parameter must be provided. primary_branch: # The name of the primary branch used for release code on this repo. This # option allows clients to specify 'main', or their own unique name, as # the branch used for repo validity checks. The default is master. env: # The path to the client's virtual environment executable on disk. For # example, Moonraker's venv is located at ~/moonraker-env/bin/python. # The default is no env, which disables updating python packages. requirements: # This is the location in the repository to the client's virtual environment # requirements file. This location is relative to the root of the repository. # This parameter must be provided if the "env" option is set, otherwise it # should be omitted. install_script: # The file location, relative to the repository, for the installation script. # The update manager parses this file for "system" packages that need updating. # The default is no install script, which disables system package updates enable_node_updates: # When set to True, Moonraker will assume that this repo relies upon node # and will attempt to execute "npm ci --only=prod" when it detects a change # to package-lock.json. Note that if your project does not have a # package-lock.json in its root directory then the plugin will fail to load. # Default is False. host_repo: # The GitHub repo in which zipped releases are hosted. Note that this does # not need to match the repository in the "origin" option, as it is possible # to use a central GitHub repository to host multiple client builds. As # an example, Moonraker's repo hosts builds for both Moonraker and Klipper. # This option defaults to the repo extracted from the "origin" option, # however if the origin is not hosted on GitHub then this parameter must # be provided. is_system_service: True # If set to true the update manager will attempt to use systemctl to restart # the service after an update has completed. This can be set to flase for # repos that are not installed as a service. The default is True. refresh_interval: # This overrides the refresh_interval set in the primary [update_manager] # section. info_tags: # Optional information tags about this application that are reported to # clients as a list of strings. Each tag should be separated by a new line. # For example: # info_tags: # desc=Special Application # klipper_restart # Clients my use these tags to perform additonal actions or display # information, see your client documentation for details on configuration. # The default is an empty list. ``` ### `[mqtt]` Enables an MQTT Client. When configured most of Moonraker's APIs are availble by publishing JSON-RPC requests to `{instance_name}/moonraker/api/request`. Responses will be published to `{instance_name}/moonraker/api/response`. See the [API Documentation](web_api.md#json-rpc-api-overview) for details on on JSON-RPC. It is also possible for other components within Moonraker to use MQTT to publish and subscribe to topics. ```ini # moonraker.conf [mqtt] address: # Address of the Broker. This may be a hostname or IP Address. This # parameter must be provided. port: # Port the Broker is listening on. Default is 1883. username: # An optional username used to log in to the Broker. This option accepts # Jinja2 Templates, see the [secrets] section for details. The default is # no username (an anonymous login will be attempted). password: # An optional password used to log in to the Broker. This option accepts # Jinja2 Templates, see the [secrets] section for details. The default is # no password. password_file: # *** DEPRECATED - Use the "password" option *** # An optional path to a text file containing a password used to log in # to the broker. It is strongly recommended that this file be located # in a folder not served by Moonraker. It is also recommended that the # password be unique and not used for other logins, as it is stored in # plain text. To create a password file, one may ssh in to the device # and enter the following commands: # cd ~ # echo mypassword > .mqttpass # Then set this option to: # ~/.mqttpass # If this option is omitted no password will be used to login. mqtt_protocol: v3.1.1 # The protocol to use when connecting to the Broker. May be v3.1, # v3.1.1, and v5. The default is v3.1.1 enable_moonraker_api: True # If set to true the MQTT client will subscribe to API topic, ie: # {instance_name}/moonraker/api/request # This can be set to False if the user does not wish to allow API # requests over MQTT. The default is True. instance_name: # An identifer used to create unique API topics for each instance of # Moonraker on network. This name cannot contain wildcards (+ or #). # For example, if the instance name is set to my_printer, Moonraker # will subscribe to the following topic for API requests: # my_printer/moonraker/api/request # Responses will be published to the following topic: # my_printer/moonraker/api/response # The default is the machine's hostname. status_objects: # A newline separated list of Klipper objects whose state will be # published in the payload of the following topic: # {instance_name}/klipper/status # For example, this option could be set as follows: # # status_objects: # webhooks # toolhead=position,print_time,homed_axes # extruder=temperature # # In the example above, all fields of the "webhooks" object will be tracked # and changes will be published. Only the "position", "print_time", and # "homed_axes" fields of the "toolhead" will be tracked. Likewise, only the # "temperature" field of the extruder will be tracked. See the # "Printer Objects" section of the documentation for an overview of the most # common objects available. # # Note that Klipper will only push an update to an object/field if the field # has changed. An object with no fields that have changed will not be part # of the payload. Object state is checked and published roughly every 250 ms. # # If not configured then no objects will be tracked and published to # the klipper/status topic. default_qos: 0 # The default QOS level used when publishing or subscribing to topics. # Must be an integer value from 0 to 2. The default is 0. api_qos: # The QOS level to use for the API topics. If not provided, the # value specified by "default_qos" will be used. ``` #### Publishing topics from Klipper It is possible to publish a topic from a Klipper gcode macro with the `publish_mqtt_topic` remote method. For example: ```ini # printer.cfg [gcode_macro PUBLISH_ALERT] gcode: {% set data = params.PAYLOAD|default(None) %} {action_call_remote_method("publish_mqtt_topic", topic="klipper/alert", payload=data, qos=0, retain=False, use_prefix=True)} ``` The `topic` is required, all other parameters are optional. Below is a brief explanation of each parameter: - `topic`: a valid mqtt topic - `payload`: Defaults to an empty payload. This can be set to string, integer, float, boolean, any json encodable object (dict or list) or None. The default value is None, in which no payload will be sent with the topic - `qos`: an integer value in the range from 0 to 2. The default is the qos set in the configuration. - `retain`: When set to True the retain flag will be set with the published topic. Defaults to False. - `use_prefix`: When set to True the configured `instance_name` will be prefixed to the topic. For example, if the instance_name is `my_printer` and the topic is `klipper/alert` the published topic will be `my_printer/klipper/alert`. The default is False. ### `[wled]` Enables control of a [WLED](https://kno.wled.ge/) strip. Moonraker always supports 4 color channel strips - the color order is defined within WLED itself. ```ini # moonraker.conf [wled strip_name] type: # The type of device. Can be either http, or serial. # This parameter must be provided. address: # The address should be a valid ip or hostname for the wled webserver. # Required when type: http serial: # The serial port to be used to communicate directly to wled. Requires wled # 0.13 Build 2108250 or later. # Required when type: serial initial_preset: # Initial preset ID (favourite) to use. If not specified initial_colors # will be used instead. initial_red: initial_green: initial_blue: initial_white: # Initial colors to use for all neopixels should initial_preset not be set, # initial_white will only be used for RGBW wled strips (defaults: 0.5) chain_count: # Number of addressable neopixels for use (default: 1) color_order: # *** DEPRECATED - Color order is defined per GPIO in WLED directly *** # Color order for WLED strip, RGB or RGBW (default: RGB) ``` Below are some examples: ```ini # moonraker.conf [wled case] type: http address: led1.lan initial_preset: 45 chain_count: 76 [wled lounge] type: http address: 192.168.0.45 initial_red: 0.5 initial_green: 0.4 initial_blue: 0.3 chain_count: 42 [wled stealthburner] type: serial serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0 initial_white: 0.6 chain_count: 3 ``` It is possible to control wled from the klippy host, this can be done using one or more macros, such as: ```ini # printer.cfg [gcode_macro WLED_ON] description: Turn WLED strip on using optional preset and resets led colors gcode: {% set strip = params.STRIP|string %} {% set preset = params.PRESET|default(-1)|int %} {action_call_remote_method("set_wled_state", strip=strip, state=True, preset=preset)} [gcode_macro WLED_OFF] description: Turn WLED strip off gcode: {% set strip = params.STRIP|string %} {action_call_remote_method("set_wled_state", strip=strip, state=False)} [gcode_macro SET_WLED] description: SET_LED like functionlity for WLED, applies to all active segments gcode: {% set strip = params.STRIP|string %} {% set red = params.RED|default(0)|float %} {% set green = params.GREEN|default(0)|float %} {% set blue = params.BLUE|default(0)|float %} {% set white = params.WHITE|default(0)|float %} {% set index = params.INDEX|default(-1)|int %} {% set transmit = params.TRANSMIT|default(1)|int %} {action_call_remote_method("set_wled", strip=strip, red=red, green=green, blue=blue, white=white, index=index, transmit=transmit)} ``` ### `[zeroconf]` Enable Zeroconf service registration allowing external services to more easily detect and use Moonraker instances. ```ini # moonraker.conf [zeroconf] ``` ### `[button]` Enables support for handling `button` events. ```ini # moonraker.conf [button my_button] type: gpio # Reserved for future use. Currently the only button type availble is # 'gpio', which is the default. pin: gpiochip0/gpio26 # The gpio pin to watch for button events. The chip is optional, if # omitted then the module will default to gpiochip0. The pin may be # inverted by specifying a "!" may be prefix. Valid examples: # gpiochip0/gpio26 # gpio26 # !gpiochip0/gpio26 # !gpio26 # Systems with libgpiod 1.5 or greater installed also support pullup and # pulldown modes. Prefix a "^" to enable the internal pullup and a "~" to # enable the internal pulldown: # ^gpiochip0/gpio26 # ^gpio26 # ~gpiochip0/gpio26 # ~gpio26 # # Its also possible to invert a pin with the pullup/pulldown enabled # ^!gpiochip0/gpio26 # ~!gpiochip0/gpio26 # This parameter must be provided min_event_time: .05 # The mimimum time (in seconds) between events to trigger a response. This is # is used to debounce buttons. This value must be at least .01 seconds. # The default is .05 seconds (50 milliseconds). on_press: on_release: # Jinja2 templates to be executed when a button event is detected. At least one # must be provided. ``` #### Button Templates Both the `on_press` and `on_release` templates are provided a context with the with two methods that may be called in addition to Jinja2's default filters adn methods: - `call_method`: Calls an internal API method. See the [API documentation](web_api.md#jinja2-template-api-calls) for details. - `send_notification`: Emits a websocket notification. This is useful if you wish to use buttons to notify attached clients of some action. This method takes an optional argument that can contain any JSON encodable type. If provided, this value will be sent as part of the payload with the notification. Additionally, the following context variables are available: - `event`: This is a dictionary with details about the event: - `elapsed_time`: The time elapsed (in seconds) since the last detected button event - `received_time`: The time the event was detected according to asyncio's monotonic clock. Note that this is not in "unix time". - `render_time`: The time the template was rendered (began execution) according to asyncio's montonic clock. It is possible execution of an event may be delayed well beyond the `received_time`. - `pressed`: A boolean value to indicate if the button is currently pressed. - `user_data`: This is a dictionary in which templates can store information that will persist across events. This may be useful to track the number of events, specific timing of events, return values from previous API calls, etc. Note that the data in this field does not persist across Moonraker restarts. !!! Warning It is recommended to avoid API calls that may block (ie: the `update` APIs). Only one event may be rendered at a time, subsequent events received will be delayed. Calling a blocking API would effectively make the button non-responsive until the API call returns. Button Template Examples: ```ini # moonraker.conf # Emergency Stop Example [button estop] type: gpio pin: gpio26 on_press: # Executes immediately after a press is detected {% do call_method("priner.emergency_stop") %} # Reboot Long Press Example [button reboot] type: gpio pin: gpio26 on_release: # Only call reboot if the button was held for more than 1 second. # Note that this won't execute until the button has been released. {% if event.elapsed_time > 1.0 %} {% do call_method("machine.reboot") %} {% endif %} # Double Click Notificaion Example [button notify_btn] type: gpio pin: gpio26 on_press: # Use the "user_data" context variable to track a single click {% set clicked = user_data.clicked|default(false) %} # It isn't possible to assign a value to a context variable in Jinja2, # however since user_data is a dict we can call its methods. The # call to __setitem__ below is equivalent to: # user_data["clicked"] = true {% do user_data.__setitem__("clicked", true) %} {% if event.elapsed_time < 0.5 and clicked %} # We will consider this a double click if the second click occurs # within .5 seconds of releasing the first {% do user_data.__setitem__("clicked", false) %} {% do user_data.__setitem__("double_clicked", true) %} {% endif %} on_release: {% set double_clicked = user_data.double_clicked|default(false) %} {% if double_clicked %} {% do user_data.__setitem__("double_clicked", false) %} {% do send_notification("Double Clicked!") %} {% endif %} ``` ### `[secrets]` Retrieves credentials and other information from a "secrets" file separate from `moonraker.conf`. This allows users to safely distribute their configuration and log files without revealing credentials and other sensitive information. ```ini # moonraker.conf [secrets] secrets_path: # A valid path to the "secrets" file. A secrets file should either be # in "ini" format (ie: the same format as moonraker.conf) or "json" # format. If the file is a "json" file, the top level item must be # an Object. When this parameter is not specified no file will be # loaded. ``` !!! Warning For maximum security the secrets file should be located in a folder not served by Moonraker. Example ini file: ```ini # moonraker_secrets.ini [mqtt_credentials] username: mqtt_user password: my_mqtt_password [home_assistant] token: long_token_string ``` Example json file: ```json { "mqtt_credentials": { "username": "mqtt_user", "password": "my_mqtt_password" }, "home_assistant" { "token": "long_token_string" } } ``` !!! Tip Generally speaking `ini` files are easier to manually edit. However, options are limited to string values without parsing and converting. The strength of `json` is that a field may be an integer, string, float, boolean, array, or object. #### Accessing secret credentials The `secrets` object is added to Moonraker's Jinja2 environment as a global, thus it is available in all templates. All options in Moonraker's configuration that accept credentials support templates. MQTT configuration example with secret credentaials: ```ini [mqtt] address: mqtt-broker.local port: 1883 # The username and password options below may be templates that # we can use to resolve stored secrets username: {secrets.mqtt_credentials.username} password: {secrets.mqtt_credentials.password} enable_moonraker_api: True ``` Home Assistant Switch Example: ```ini # moonraker.conf [power homeassistant_switch] type: homeassistant address: home-assistant-host.local port: 8123 device: switch.1234567890abcdefghij # The token option may be a template token: {secrets.home_assistant.token} domain: switch ``` ## Jinja2 Templates Some Moonraker configuration options make use of Jinja2 Templates. For consistency, Moonraker uses the same Jinja2 syntax as Klipper. Statements should be enclosed in `{% %}`, and expressions in `{ }`. There are some key differences, as outlined below: - Moonraker templates do not currently include globals like `printer` and `params` in the context. Variables included in the context will be specified in the option's documentation. - Moonraker's template environment adds the `ext.do` extension. The `{% do expression %}` statement can be used to modify variables without printing any text. See the example below for details. - Klipper uses Jinja2 exclusively for evaluating gcode statements. Moonraker uses it to provide configuration options that may need to change based on runtime parameters. For an example of how to use the `do` statement, lets assume we need to send a specific json payload with an MQTT power device command. Rather than attempt to type out the json ourselves, it may be easier to create a `dictionary` object and convert it to json: ```ini # moonraker.conf [power my_mqtt_device] type: mqtt command_topic: my/mqtt/command # Lets assume this device requres a json payload with each command. # We will use a dict to generate the payload command_payload: {% set my_payload = {"SOME_FIELD": ""} %} # example of calling the dict.update method {% do my_payload.update({"SOME_FIELD": "a string value"}) %} # Here we set the actual command, the "command" variable # is passed to the context of this template {% do my_payload.__setitem__("POWER_COMMAND", command) %} # generate the json output { my_payload|tojson } ```