power: add RF transmitter support

Signed-off: Daniel Bauer <github@dbauer.me>

docs/configuration.md

@@ -190,7 +190,7 @@ gcode:
 ```
 
 ## `[power]`
-Enables device power control.  Currently GPIO (relays), TPLink Smartplug,
+Enables device power control.  Currently GPIO (relays), RF transmitter, TPLink Smartplug,
 and Tasmota (via http) devices, HomeAssistant switch are supported.
 
 ```ini
@@ -198,7 +198,7 @@ and Tasmota (via http) devices, HomeAssistant switch are supported.
 
 [power device_name]
 type: gpio
-#   The type of device.  Can be either gpio, tplink_smartplug, tasmota
+#   The type of device.  Can be either gpio, rf, tplink_smartplug, tasmota
 #   shelly, homeseer, homeassistant, or loxonev1.
 #   This parameter must be provided.
 off_when_shutdown: False
@@ -217,7 +217,7 @@ restart_delay: 1.
 #   If "restart_klipper_when_powered" is set, this option specifies the amount
 #   of time (in seconds) to delay the restart.  Default is 1 second.
 pin: gpiochip0/gpio26
-#   The pin to use for GPIO devices.  The chip is optional, if left out
+#   The pin to use for GPIO and RF devices.  The chip is optional, if left out
 #   then the module will default to gpiochip0.  If one wishes to invert
 #   the signal, a "!" may be prefixed to the pin.  Valid examples:
 #      gpiochip0/gpio26
@@ -297,6 +297,12 @@ output_id:
 #   The output_id is the name of a programmed output, virtual input or virtual
 #   output in the loxone config his output_id (name) may only be used once in
 #   the loxone config
+on_code:
+off_code:
+#   The above options are used for "rf" devices.  The
+#   codes should be valid binary codes that are send via the RF transmitter.
+#   For example: 1011.
+
 ```
 Below are some potential examples:
 ```ini

moonraker/components/power.py

@@ -12,6 +12,7 @@ import json
 import struct
 import socket
 import asyncio
+import time
 from tornado.iostream import IOStream
 from tornado.httpclient import AsyncHTTPClient
 from tornado.escape import json_decode
@@ -68,7 +69,8 @@ class PrinterPower:
             "shelly": Shelly,
             "homeseer": HomeSeer,
             "homeassistant": HomeAssistant,
-            "loxonev1": Loxonev1
+            "loxonev1": Loxonev1,
+            "rf": RFDevice
         }
         try:
             for section in prefix_sections:
@@ -79,7 +81,7 @@ class PrinterPower:
                 if dev_class is None:
                     raise config.error(f"Unsupported Device Type: {dev_type}")
                 dev = dev_class(cfg)
-                if isinstance(dev, GpioDevice):
+                if isinstance(dev, GpioDevice) or isinstance(dev, RFDevice):
                     if not HAS_GPIOD:
                         continue
                     dev.configure_line(cfg, self.chip_factory)
@@ -470,6 +472,53 @@ class GpioDevice(PowerDevice):
     def close(self) -> None:
         self.line.release()
 
+class RFDevice(GpioDevice):
+
+    # Protocol definition
+    # [1, 3] means HIGH is set for 1x pulse_len and LOW for 3x pulse_len
+    ZERO_BIT = [1, 3]  # zero bit
+    ONE_BIT = [3, 1]  # one bit
+    SYNC_BIT = [1, 31]  # sync between
+    PULSE_LEN = 0.00035  # length of a single pulse
+    RETRIES = 10  # send the code this many times
+
+    def __init__(self, config: ConfigHelper):
+        super().__init__(config)
+        self.on = config.get("on_code").zfill(24)
+        self.off = config.get("off_code").zfill(24)
+
+    def initialize(self) -> None:
+        self.set_power("on" if self.initial_state else "off")
+
+    def _transmit_digit(self, waveform) -> None:
+        self.line.set_value(1)
+        time.sleep(waveform[0]*RFDevice.PULSE_LEN)
+        self.line.set_value(0)
+        time.sleep(waveform[1]*RFDevice.PULSE_LEN)
+
+    def _transmit_code(self, code) -> None:
+        for _ in range(RFDevice.RETRIES):
+            for i in code:
+                if i == "1":
+                    self._transmit_digit(RFDevice.ONE_BIT)
+                elif i == "0":
+                    self._transmit_digit(RFDevice.ZERO_BIT)
+            self._transmit_digit(RFDevice.SYNC_BIT)
+
+    def set_power(self, state) -> None:
+        try:
+            if state == "on":
+                code = self.on
+            else:
+                code = self.off
+            self._transmit_code(code)
+        except Exception:
+            self.state = "error"
+            msg = f"Error Toggling Device Power: {self.name}"
+            logging.exception(msg)
+            raise self.server.error(msg) from None
+        self.state = state
+
 
 #  This implementation based off the work tplink_smartplug
 #  script by Lubomir Stroetmann available at: