1368 lines
48 KiB
C
1368 lines
48 KiB
C
/**
|
|
******************************************************************************
|
|
* @file stm32f1xx_hal_dac.c
|
|
* @author MCD Application Team
|
|
* @brief DAC HAL module driver.
|
|
* This file provides firmware functions to manage the following
|
|
* functionalities of the Digital to Analog Converter (DAC) peripheral:
|
|
* + Initialization and de-initialization functions
|
|
* + IO operation functions
|
|
* + Peripheral Control functions
|
|
* + Peripheral State and Errors functions
|
|
*
|
|
*
|
|
@verbatim
|
|
==============================================================================
|
|
##### DAC Peripheral features #####
|
|
==============================================================================
|
|
[..]
|
|
*** DAC Channels ***
|
|
====================
|
|
[..]
|
|
STM32F1 devices integrate two 12-bit Digital Analog Converters
|
|
|
|
The 2 converters (i.e. channel1 & channel2)
|
|
can be used independently or simultaneously (dual mode):
|
|
(#) DAC channel1 with DAC_OUT1 (PA4) as output or connected to on-chip
|
|
peripherals (ex. timers).
|
|
(#) DAC channel2 with DAC_OUT2 (PA5) as output or connected to on-chip
|
|
peripherals (ex. timers).
|
|
|
|
*** DAC Triggers ***
|
|
====================
|
|
[..]
|
|
Digital to Analog conversion can be non-triggered using DAC_TRIGGER_NONE
|
|
and DAC_OUT1/DAC_OUT2 is available once writing to DHRx register.
|
|
[..]
|
|
Digital to Analog conversion can be triggered by:
|
|
(#) External event: EXTI Line 9 (any GPIOx_PIN_9) using DAC_TRIGGER_EXT_IT9.
|
|
The used pin (GPIOx_PIN_9) must be configured in input mode.
|
|
|
|
(#) Timers TRGO: TIM2, TIM4, TIM6, TIM7
|
|
For STM32F10x connectivity line devices and STM32F100x devices: TIM3
|
|
For STM32F10x high-density and XL-density devices: TIM8
|
|
For STM32F100x high-density value line devices: TIM15 as
|
|
replacement of TIM5.
|
|
(DAC_TRIGGER_T2_TRGO, DAC_TRIGGER_T4_TRGO...)
|
|
|
|
(#) Software using DAC_TRIGGER_SOFTWARE
|
|
|
|
*** DAC Buffer mode feature ***
|
|
===============================
|
|
[..]
|
|
Each DAC channel integrates an output buffer that can be used to
|
|
reduce the output impedance, and to drive external loads directly
|
|
without having to add an external operational amplifier.
|
|
To enable, the output buffer use
|
|
sConfig.DAC_OutputBuffer = DAC_OUTPUTBUFFER_ENABLE;
|
|
[..]
|
|
(@) Refer to the device datasheet for more details about output
|
|
impedance value with and without output buffer.
|
|
|
|
*** DAC connect feature ***
|
|
===============================
|
|
[..]
|
|
Each DAC channel can be connected internally.
|
|
To connect, use
|
|
sConfig.DAC_ConnectOnChipPeripheral = DAC_CHIPCONNECT_ENABLE;
|
|
|
|
*** GPIO configurations guidelines ***
|
|
=====================
|
|
[..]
|
|
When a DAC channel is used (ex channel1 on PA4) and the other is not
|
|
(ex channel2 on PA5 is configured in Analog and disabled).
|
|
Channel1 may disturb channel2 as coupling effect.
|
|
Note that there is no coupling on channel2 as soon as channel2 is turned on.
|
|
Coupling on adjacent channel could be avoided as follows:
|
|
when unused PA5 is configured as INPUT PULL-UP or DOWN.
|
|
PA5 is configured in ANALOG just before it is turned on.
|
|
|
|
*** DAC wave generation feature ***
|
|
===================================
|
|
[..]
|
|
Both DAC channels can be used to generate
|
|
(#) Noise wave
|
|
(#) Triangle wave
|
|
|
|
*** DAC data format ***
|
|
=======================
|
|
[..]
|
|
The DAC data format can be:
|
|
(#) 8-bit right alignment using DAC_ALIGN_8B_R
|
|
(#) 12-bit left alignment using DAC_ALIGN_12B_L
|
|
(#) 12-bit right alignment using DAC_ALIGN_12B_R
|
|
|
|
*** DAC data value to voltage correspondence ***
|
|
================================================
|
|
[..]
|
|
The analog output voltage on each DAC channel pin is determined
|
|
by the following equation:
|
|
[..]
|
|
DAC_OUTx = VREF+ * DOR / 4095
|
|
(+) with DOR is the Data Output Register
|
|
[..]
|
|
VEF+ is the input voltage reference (refer to the device datasheet)
|
|
[..]
|
|
e.g. To set DAC_OUT1 to 0.7V, use
|
|
(+) Assuming that VREF+ = 3.3V, DAC_OUT1 = (3.3 * 868) / 4095 = 0.7V
|
|
|
|
*** DMA requests ***
|
|
=====================
|
|
[..]
|
|
A DMA request can be generated when an external trigger (but not a software trigger)
|
|
occurs if DMA1 requests are enabled using HAL_DAC_Start_DMA().
|
|
DMA1 requests are mapped as following:
|
|
(#) DAC channel1 mapped on DMA1 channel3
|
|
for STM32F100x low-density, medium-density, high-density with DAC
|
|
DMA remap:
|
|
(#) DAC channel2 mapped on DMA2 channel3
|
|
for STM32F100x high-density without DAC DMA remap and other
|
|
STM32F1 devices
|
|
|
|
[..]
|
|
(@) For Dual mode and specific signal (Triangle and noise) generation please
|
|
refer to Extended Features Driver description
|
|
|
|
##### How to use this driver #####
|
|
==============================================================================
|
|
[..]
|
|
(+) DAC APB clock must be enabled to get write access to DAC
|
|
registers using HAL_DAC_Init()
|
|
(+) Configure DAC_OUTx (DAC_OUT1: PA4, DAC_OUT2: PA5) in analog mode.
|
|
(+) Configure the DAC channel using HAL_DAC_ConfigChannel() function.
|
|
(+) Enable the DAC channel using HAL_DAC_Start() or HAL_DAC_Start_DMA() functions.
|
|
|
|
|
|
*** Polling mode IO operation ***
|
|
=================================
|
|
[..]
|
|
(+) Start the DAC peripheral using HAL_DAC_Start()
|
|
(+) To read the DAC last data output value, use the HAL_DAC_GetValue() function.
|
|
(+) Stop the DAC peripheral using HAL_DAC_Stop()
|
|
|
|
*** DMA mode IO operation ***
|
|
==============================
|
|
[..]
|
|
(+) Start the DAC peripheral using HAL_DAC_Start_DMA(), at this stage the user specify the length
|
|
of data to be transferred at each end of conversion
|
|
First issued trigger will start the conversion of the value previously set by HAL_DAC_SetValue().
|
|
(+) At the middle of data transfer HAL_DAC_ConvHalfCpltCallbackCh1() or HAL_DACEx_ConvHalfCpltCallbackCh2()
|
|
function is executed and user can add his own code by customization of function pointer
|
|
HAL_DAC_ConvHalfCpltCallbackCh1() or HAL_DACEx_ConvHalfCpltCallbackCh2()
|
|
(+) At The end of data transfer HAL_DAC_ConvCpltCallbackCh1() or HAL_DACEx_ConvHalfCpltCallbackCh2()
|
|
function is executed and user can add his own code by customization of function pointer
|
|
HAL_DAC_ConvCpltCallbackCh1() or HAL_DACEx_ConvHalfCpltCallbackCh2()
|
|
(+) In case of transfer Error, HAL_DAC_ErrorCallbackCh1() function is executed and user can
|
|
add his own code by customization of function pointer HAL_DAC_ErrorCallbackCh1
|
|
(+) For STM32F100x devices with specific feature: DMA underrun.
|
|
In case of DMA underrun, DAC interruption triggers and execute internal function HAL_DAC_IRQHandler.
|
|
HAL_DAC_DMAUnderrunCallbackCh1() or HAL_DACEx_DMAUnderrunCallbackCh2()
|
|
function is executed and user can add his own code by customization of function pointer
|
|
HAL_DAC_DMAUnderrunCallbackCh1() or HAL_DACEx_DMAUnderrunCallbackCh2() and
|
|
add his own code by customization of function pointer HAL_DAC_ErrorCallbackCh1()
|
|
(+) Stop the DAC peripheral using HAL_DAC_Stop_DMA()
|
|
|
|
*** Callback registration ***
|
|
=============================================
|
|
[..]
|
|
The compilation define USE_HAL_DAC_REGISTER_CALLBACKS when set to 1
|
|
allows the user to configure dynamically the driver callbacks.
|
|
|
|
Use Functions @ref HAL_DAC_RegisterCallback() to register a user callback,
|
|
it allows to register following callbacks:
|
|
(+) ConvCpltCallbackCh1 : callback when a half transfer is completed on Ch1.
|
|
(+) ConvHalfCpltCallbackCh1 : callback when a transfer is completed on Ch1.
|
|
(+) ErrorCallbackCh1 : callback when an error occurs on Ch1.
|
|
(+) DMAUnderrunCallbackCh1 : callback when an underrun error occurs on Ch1.
|
|
(+) ConvCpltCallbackCh2 : callback when a half transfer is completed on Ch2.
|
|
(+) ConvHalfCpltCallbackCh2 : callback when a transfer is completed on Ch2.
|
|
(+) ErrorCallbackCh2 : callback when an error occurs on Ch2.
|
|
(+) DMAUnderrunCallbackCh2 : callback when an underrun error occurs on Ch2.
|
|
(+) MspInitCallback : DAC MspInit.
|
|
(+) MspDeInitCallback : DAC MspdeInit.
|
|
This function takes as parameters the HAL peripheral handle, the Callback ID
|
|
and a pointer to the user callback function.
|
|
|
|
Use function @ref HAL_DAC_UnRegisterCallback() to reset a callback to the default
|
|
weak (surcharged) function. It allows to reset following callbacks:
|
|
(+) ConvCpltCallbackCh1 : callback when a half transfer is completed on Ch1.
|
|
(+) ConvHalfCpltCallbackCh1 : callback when a transfer is completed on Ch1.
|
|
(+) ErrorCallbackCh1 : callback when an error occurs on Ch1.
|
|
(+) DMAUnderrunCallbackCh1 : callback when an underrun error occurs on Ch1.
|
|
(+) ConvCpltCallbackCh2 : callback when a half transfer is completed on Ch2.
|
|
(+) ConvHalfCpltCallbackCh2 : callback when a transfer is completed on Ch2.
|
|
(+) ErrorCallbackCh2 : callback when an error occurs on Ch2.
|
|
(+) DMAUnderrunCallbackCh2 : callback when an underrun error occurs on Ch2.
|
|
(+) MspInitCallback : DAC MspInit.
|
|
(+) MspDeInitCallback : DAC MspdeInit.
|
|
(+) All Callbacks
|
|
This function) takes as parameters the HAL peripheral handle and the Callback ID.
|
|
|
|
By default, after the @ref HAL_DAC_Init and if the state is HAL_DAC_STATE_RESET
|
|
all callbacks are reset to the corresponding legacy weak (surcharged) functions.
|
|
Exception done for MspInit and MspDeInit callbacks that are respectively
|
|
reset to the legacy weak (surcharged) functions in the @ref HAL_DAC_Init
|
|
and @ref HAL_DAC_DeInit only when these callbacks are null (not registered beforehand).
|
|
If not, MspInit or MspDeInit are not null, the @ref HAL_DAC_Init and @ref HAL_DAC_DeInit
|
|
keep and use the user MspInit/MspDeInit callbacks (registered beforehand)
|
|
|
|
Callbacks can be registered/unregistered in READY state only.
|
|
Exception done for MspInit/MspDeInit callbacks that can be registered/unregistered
|
|
in READY or RESET state, thus registered (user) MspInit/DeInit callbacks can be used
|
|
during the Init/DeInit.
|
|
In that case first register the MspInit/MspDeInit user callbacks
|
|
using @ref HAL_DAC_RegisterCallback before calling @ref HAL_DAC_DeInit
|
|
or @ref HAL_DAC_Init function.
|
|
|
|
When The compilation define USE_HAL_DAC_REGISTER_CALLBACKS is set to 0 or
|
|
not defined, the callback registering feature is not available
|
|
and weak (surcharged) callbacks are used.
|
|
|
|
*** DAC HAL driver macros list ***
|
|
=============================================
|
|
[..]
|
|
Below the list of most used macros in DAC HAL driver.
|
|
|
|
(+) __HAL_DAC_ENABLE : Enable the DAC peripheral (For STM32F100x devices with specific feature: DMA underrun)
|
|
(+) __HAL_DAC_DISABLE : Disable the DAC peripheral (For STM32F100x devices with specific feature: DMA underrun)
|
|
(+) __HAL_DAC_CLEAR_FLAG: Clear the DAC's pending flags (For STM32F100x devices with specific feature: DMA underrun)
|
|
(+) __HAL_DAC_GET_FLAG: Get the selected DAC's flag status (For STM32F100x devices with specific feature: DMA underrun)
|
|
|
|
[..]
|
|
(@) You can refer to the DAC HAL driver header file for more useful macros
|
|
|
|
@endverbatim
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
*/
|
|
|
|
/* Includes ------------------------------------------------------------------*/
|
|
#include "stm32f1xx_hal.h"
|
|
|
|
/** @addtogroup STM32F1xx_HAL_Driver
|
|
* @{
|
|
*/
|
|
|
|
#ifdef HAL_DAC_MODULE_ENABLED
|
|
#if defined(DAC)
|
|
|
|
/** @defgroup DAC DAC
|
|
* @brief DAC driver modules
|
|
* @{
|
|
*/
|
|
|
|
/* Private typedef -----------------------------------------------------------*/
|
|
/* Private define ------------------------------------------------------------*/
|
|
/* Private constants ---------------------------------------------------------*/
|
|
/* Private macro -------------------------------------------------------------*/
|
|
/* Private variables ---------------------------------------------------------*/
|
|
/* Private function prototypes -----------------------------------------------*/
|
|
/* Exported functions -------------------------------------------------------*/
|
|
|
|
/** @defgroup DAC_Exported_Functions DAC Exported Functions
|
|
* @{
|
|
*/
|
|
|
|
/** @defgroup DAC_Exported_Functions_Group1 Initialization and de-initialization functions
|
|
* @brief Initialization and Configuration functions
|
|
*
|
|
@verbatim
|
|
==============================================================================
|
|
##### Initialization and de-initialization functions #####
|
|
==============================================================================
|
|
[..] This section provides functions allowing to:
|
|
(+) Initialize and configure the DAC.
|
|
(+) De-initialize the DAC.
|
|
|
|
@endverbatim
|
|
* @{
|
|
*/
|
|
|
|
/**
|
|
* @brief Initialize the DAC peripheral according to the specified parameters
|
|
* in the DAC_InitStruct and initialize the associated handle.
|
|
* @param hdac pointer to a DAC_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DAC.
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_DAC_Init(DAC_HandleTypeDef *hdac)
|
|
{
|
|
/* Check DAC handle */
|
|
if (hdac == NULL)
|
|
{
|
|
return HAL_ERROR;
|
|
}
|
|
/* Check the parameters */
|
|
assert_param(IS_DAC_ALL_INSTANCE(hdac->Instance));
|
|
|
|
if (hdac->State == HAL_DAC_STATE_RESET)
|
|
{
|
|
#if (USE_HAL_DAC_REGISTER_CALLBACKS == 1)
|
|
/* Init the DAC Callback settings */
|
|
hdac->ConvCpltCallbackCh1 = HAL_DAC_ConvCpltCallbackCh1;
|
|
hdac->ConvHalfCpltCallbackCh1 = HAL_DAC_ConvHalfCpltCallbackCh1;
|
|
hdac->ErrorCallbackCh1 = HAL_DAC_ErrorCallbackCh1;
|
|
hdac->DMAUnderrunCallbackCh1 = HAL_DAC_DMAUnderrunCallbackCh1;
|
|
|
|
hdac->ConvCpltCallbackCh2 = HAL_DACEx_ConvCpltCallbackCh2;
|
|
hdac->ConvHalfCpltCallbackCh2 = HAL_DACEx_ConvHalfCpltCallbackCh2;
|
|
hdac->ErrorCallbackCh2 = HAL_DACEx_ErrorCallbackCh2;
|
|
hdac->DMAUnderrunCallbackCh2 = HAL_DACEx_DMAUnderrunCallbackCh2;
|
|
|
|
if (hdac->MspInitCallback == NULL)
|
|
{
|
|
hdac->MspInitCallback = HAL_DAC_MspInit;
|
|
}
|
|
#endif /* USE_HAL_DAC_REGISTER_CALLBACKS */
|
|
|
|
/* Allocate lock resource and initialize it */
|
|
hdac->Lock = HAL_UNLOCKED;
|
|
|
|
#if (USE_HAL_DAC_REGISTER_CALLBACKS == 1)
|
|
/* Init the low level hardware */
|
|
hdac->MspInitCallback(hdac);
|
|
#else
|
|
/* Init the low level hardware */
|
|
HAL_DAC_MspInit(hdac);
|
|
#endif /* USE_HAL_DAC_REGISTER_CALLBACKS */
|
|
}
|
|
|
|
/* Initialize the DAC state*/
|
|
hdac->State = HAL_DAC_STATE_BUSY;
|
|
|
|
/* Set DAC error code to none */
|
|
hdac->ErrorCode = HAL_DAC_ERROR_NONE;
|
|
|
|
/* Initialize the DAC state*/
|
|
hdac->State = HAL_DAC_STATE_READY;
|
|
|
|
/* Return function status */
|
|
return HAL_OK;
|
|
}
|
|
|
|
/**
|
|
* @brief Deinitialize the DAC peripheral registers to their default reset values.
|
|
* @param hdac pointer to a DAC_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DAC.
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_DAC_DeInit(DAC_HandleTypeDef *hdac)
|
|
{
|
|
/* Check DAC handle */
|
|
if (hdac == NULL)
|
|
{
|
|
return HAL_ERROR;
|
|
}
|
|
|
|
/* Check the parameters */
|
|
assert_param(IS_DAC_ALL_INSTANCE(hdac->Instance));
|
|
|
|
/* Change DAC state */
|
|
hdac->State = HAL_DAC_STATE_BUSY;
|
|
|
|
#if (USE_HAL_DAC_REGISTER_CALLBACKS == 1)
|
|
if (hdac->MspDeInitCallback == NULL)
|
|
{
|
|
hdac->MspDeInitCallback = HAL_DAC_MspDeInit;
|
|
}
|
|
/* DeInit the low level hardware */
|
|
hdac->MspDeInitCallback(hdac);
|
|
#else
|
|
/* DeInit the low level hardware */
|
|
HAL_DAC_MspDeInit(hdac);
|
|
#endif /* USE_HAL_DAC_REGISTER_CALLBACKS */
|
|
|
|
/* Set DAC error code to none */
|
|
hdac->ErrorCode = HAL_DAC_ERROR_NONE;
|
|
|
|
/* Change DAC state */
|
|
hdac->State = HAL_DAC_STATE_RESET;
|
|
|
|
/* Release Lock */
|
|
__HAL_UNLOCK(hdac);
|
|
|
|
/* Return function status */
|
|
return HAL_OK;
|
|
}
|
|
|
|
/**
|
|
* @brief Initialize the DAC MSP.
|
|
* @param hdac pointer to a DAC_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DAC.
|
|
* @retval None
|
|
*/
|
|
__weak void HAL_DAC_MspInit(DAC_HandleTypeDef *hdac)
|
|
{
|
|
/* Prevent unused argument(s) compilation warning */
|
|
UNUSED(hdac);
|
|
|
|
/* NOTE : This function should not be modified, when the callback is needed,
|
|
the HAL_DAC_MspInit could be implemented in the user file
|
|
*/
|
|
}
|
|
|
|
/**
|
|
* @brief DeInitialize the DAC MSP.
|
|
* @param hdac pointer to a DAC_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DAC.
|
|
* @retval None
|
|
*/
|
|
__weak void HAL_DAC_MspDeInit(DAC_HandleTypeDef *hdac)
|
|
{
|
|
/* Prevent unused argument(s) compilation warning */
|
|
UNUSED(hdac);
|
|
|
|
/* NOTE : This function should not be modified, when the callback is needed,
|
|
the HAL_DAC_MspDeInit could be implemented in the user file
|
|
*/
|
|
}
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup DAC_Exported_Functions_Group2 IO operation functions
|
|
* @brief IO operation functions
|
|
*
|
|
@verbatim
|
|
==============================================================================
|
|
##### IO operation functions #####
|
|
==============================================================================
|
|
[..] This section provides functions allowing to:
|
|
(+) Start conversion.
|
|
(+) Stop conversion.
|
|
(+) Start conversion and enable DMA transfer.
|
|
(+) Stop conversion and disable DMA transfer.
|
|
(+) Get result of conversion.
|
|
|
|
@endverbatim
|
|
* @{
|
|
*/
|
|
|
|
/**
|
|
* @brief Enables DAC and starts conversion of channel.
|
|
* @param hdac pointer to a DAC_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DAC.
|
|
* @param Channel The selected DAC channel.
|
|
* This parameter can be one of the following values:
|
|
* @arg DAC_CHANNEL_1: DAC Channel1 selected
|
|
* @arg DAC_CHANNEL_2: DAC Channel2 selected
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_DAC_Start(DAC_HandleTypeDef *hdac, uint32_t Channel)
|
|
{
|
|
/* Check the parameters */
|
|
assert_param(IS_DAC_CHANNEL(Channel));
|
|
|
|
/* Process locked */
|
|
__HAL_LOCK(hdac);
|
|
|
|
/* Change DAC state */
|
|
hdac->State = HAL_DAC_STATE_BUSY;
|
|
|
|
/* Enable the Peripheral */
|
|
__HAL_DAC_ENABLE(hdac, Channel);
|
|
|
|
if (Channel == DAC_CHANNEL_1)
|
|
{
|
|
/* Check if software trigger enabled */
|
|
if ((hdac->Instance->CR & (DAC_CR_TEN1 | DAC_CR_TSEL1)) == DAC_TRIGGER_SOFTWARE)
|
|
{
|
|
/* Enable the selected DAC software conversion */
|
|
SET_BIT(hdac->Instance->SWTRIGR, DAC_SWTRIGR_SWTRIG1);
|
|
}
|
|
}
|
|
else
|
|
{
|
|
/* Check if software trigger enabled */
|
|
if ((hdac->Instance->CR & (DAC_CR_TEN2 | DAC_CR_TSEL2)) == (DAC_TRIGGER_SOFTWARE << (Channel & 0x10UL)))
|
|
{
|
|
/* Enable the selected DAC software conversion*/
|
|
SET_BIT(hdac->Instance->SWTRIGR, DAC_SWTRIGR_SWTRIG2);
|
|
}
|
|
}
|
|
|
|
/* Change DAC state */
|
|
hdac->State = HAL_DAC_STATE_READY;
|
|
|
|
/* Process unlocked */
|
|
__HAL_UNLOCK(hdac);
|
|
|
|
/* Return function status */
|
|
return HAL_OK;
|
|
}
|
|
|
|
/**
|
|
* @brief Disables DAC and stop conversion of channel.
|
|
* @param hdac pointer to a DAC_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DAC.
|
|
* @param Channel The selected DAC channel.
|
|
* This parameter can be one of the following values:
|
|
* @arg DAC_CHANNEL_1: DAC Channel1 selected
|
|
* @arg DAC_CHANNEL_2: DAC Channel2 selected
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_DAC_Stop(DAC_HandleTypeDef *hdac, uint32_t Channel)
|
|
{
|
|
/* Check the parameters */
|
|
assert_param(IS_DAC_CHANNEL(Channel));
|
|
|
|
/* Disable the Peripheral */
|
|
__HAL_DAC_DISABLE(hdac, Channel);
|
|
|
|
/* Change DAC state */
|
|
hdac->State = HAL_DAC_STATE_READY;
|
|
|
|
/* Return function status */
|
|
return HAL_OK;
|
|
}
|
|
|
|
/**
|
|
* @brief Enables DAC and starts conversion of channel.
|
|
* @param hdac pointer to a DAC_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DAC.
|
|
* @param Channel The selected DAC channel.
|
|
* This parameter can be one of the following values:
|
|
* @arg DAC_CHANNEL_1: DAC Channel1 selected
|
|
* @arg DAC_CHANNEL_2: DAC Channel2 selected
|
|
* @param pData The destination peripheral Buffer address.
|
|
* @param Length The length of data to be transferred from memory to DAC peripheral
|
|
* @param Alignment Specifies the data alignment for DAC channel.
|
|
* This parameter can be one of the following values:
|
|
* @arg DAC_ALIGN_8B_R: 8bit right data alignment selected
|
|
* @arg DAC_ALIGN_12B_L: 12bit left data alignment selected
|
|
* @arg DAC_ALIGN_12B_R: 12bit right data alignment selected
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_DAC_Start_DMA(DAC_HandleTypeDef *hdac, uint32_t Channel, uint32_t *pData, uint32_t Length,
|
|
uint32_t Alignment)
|
|
{
|
|
HAL_StatusTypeDef status;
|
|
uint32_t tmpreg = 0U;
|
|
|
|
/* Check the parameters */
|
|
assert_param(IS_DAC_CHANNEL(Channel));
|
|
assert_param(IS_DAC_ALIGN(Alignment));
|
|
|
|
/* Process locked */
|
|
__HAL_LOCK(hdac);
|
|
|
|
/* Change DAC state */
|
|
hdac->State = HAL_DAC_STATE_BUSY;
|
|
|
|
if (Channel == DAC_CHANNEL_1)
|
|
{
|
|
/* Set the DMA transfer complete callback for channel1 */
|
|
hdac->DMA_Handle1->XferCpltCallback = DAC_DMAConvCpltCh1;
|
|
|
|
/* Set the DMA half transfer complete callback for channel1 */
|
|
hdac->DMA_Handle1->XferHalfCpltCallback = DAC_DMAHalfConvCpltCh1;
|
|
|
|
/* Set the DMA error callback for channel1 */
|
|
hdac->DMA_Handle1->XferErrorCallback = DAC_DMAErrorCh1;
|
|
|
|
/* Enable the selected DAC channel1 DMA request */
|
|
SET_BIT(hdac->Instance->CR, DAC_CR_DMAEN1);
|
|
|
|
/* Case of use of channel 1 */
|
|
switch (Alignment)
|
|
{
|
|
case DAC_ALIGN_12B_R:
|
|
/* Get DHR12R1 address */
|
|
tmpreg = (uint32_t)&hdac->Instance->DHR12R1;
|
|
break;
|
|
case DAC_ALIGN_12B_L:
|
|
/* Get DHR12L1 address */
|
|
tmpreg = (uint32_t)&hdac->Instance->DHR12L1;
|
|
break;
|
|
case DAC_ALIGN_8B_R:
|
|
/* Get DHR8R1 address */
|
|
tmpreg = (uint32_t)&hdac->Instance->DHR8R1;
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
else
|
|
{
|
|
/* Set the DMA transfer complete callback for channel2 */
|
|
hdac->DMA_Handle2->XferCpltCallback = DAC_DMAConvCpltCh2;
|
|
|
|
/* Set the DMA half transfer complete callback for channel2 */
|
|
hdac->DMA_Handle2->XferHalfCpltCallback = DAC_DMAHalfConvCpltCh2;
|
|
|
|
/* Set the DMA error callback for channel2 */
|
|
hdac->DMA_Handle2->XferErrorCallback = DAC_DMAErrorCh2;
|
|
|
|
/* Enable the selected DAC channel2 DMA request */
|
|
SET_BIT(hdac->Instance->CR, DAC_CR_DMAEN2);
|
|
|
|
/* Case of use of channel 2 */
|
|
switch (Alignment)
|
|
{
|
|
case DAC_ALIGN_12B_R:
|
|
/* Get DHR12R2 address */
|
|
tmpreg = (uint32_t)&hdac->Instance->DHR12R2;
|
|
break;
|
|
case DAC_ALIGN_12B_L:
|
|
/* Get DHR12L2 address */
|
|
tmpreg = (uint32_t)&hdac->Instance->DHR12L2;
|
|
break;
|
|
case DAC_ALIGN_8B_R:
|
|
/* Get DHR8R2 address */
|
|
tmpreg = (uint32_t)&hdac->Instance->DHR8R2;
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
|
|
/* Enable the DMA Stream */
|
|
if (Channel == DAC_CHANNEL_1)
|
|
{
|
|
#if defined(DAC_CR_DMAUDRIE1)
|
|
/* Enable the DAC DMA underrun interrupt */
|
|
__HAL_DAC_ENABLE_IT(hdac, DAC_IT_DMAUDR1);
|
|
#endif /* DAC_CR_DMAUDRIE1 */
|
|
/* Enable the DMA Stream */
|
|
status = HAL_DMA_Start_IT(hdac->DMA_Handle1, (uint32_t)pData, tmpreg, Length);
|
|
}
|
|
else
|
|
{
|
|
#if defined(DAC_CR_DMAUDRIE2)
|
|
/* Enable the DAC DMA underrun interrupt */
|
|
__HAL_DAC_ENABLE_IT(hdac, DAC_IT_DMAUDR2);
|
|
#endif /* DAC_CR_DMAUDRIE2 */
|
|
/* Enable the DMA Stream */
|
|
status = HAL_DMA_Start_IT(hdac->DMA_Handle2, (uint32_t)pData, tmpreg, Length);
|
|
}
|
|
|
|
/* Process Unlocked */
|
|
__HAL_UNLOCK(hdac);
|
|
|
|
if (status == HAL_OK)
|
|
{
|
|
/* Enable the Peripheral */
|
|
__HAL_DAC_ENABLE(hdac, Channel);
|
|
}
|
|
else
|
|
{
|
|
hdac->ErrorCode |= HAL_DAC_ERROR_DMA;
|
|
}
|
|
|
|
/* Return function status */
|
|
return status;
|
|
}
|
|
|
|
/**
|
|
* @brief Disables DAC and stop conversion of channel.
|
|
* @param hdac pointer to a DAC_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DAC.
|
|
* @param Channel The selected DAC channel.
|
|
* This parameter can be one of the following values:
|
|
* @arg DAC_CHANNEL_1: DAC Channel1 selected
|
|
* @arg DAC_CHANNEL_2: DAC Channel2 selected
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_DAC_Stop_DMA(DAC_HandleTypeDef *hdac, uint32_t Channel)
|
|
{
|
|
HAL_StatusTypeDef status;
|
|
|
|
/* Check the parameters */
|
|
assert_param(IS_DAC_CHANNEL(Channel));
|
|
|
|
/* Disable the selected DAC channel DMA request */
|
|
hdac->Instance->CR &= ~(DAC_CR_DMAEN1 << (Channel & 0x10UL));
|
|
|
|
/* Disable the Peripheral */
|
|
__HAL_DAC_DISABLE(hdac, Channel);
|
|
|
|
/* Disable the DMA Stream */
|
|
|
|
/* Channel1 is used */
|
|
if (Channel == DAC_CHANNEL_1)
|
|
{
|
|
/* Disable the DMA Stream */
|
|
status = HAL_DMA_Abort(hdac->DMA_Handle1);
|
|
#if defined(DAC_CR_DMAUDRIE1)
|
|
/* Disable the DAC DMA underrun interrupt */
|
|
__HAL_DAC_DISABLE_IT(hdac, DAC_IT_DMAUDR1);
|
|
#endif /* DAC_CR_DMAUDRIE1 */
|
|
}
|
|
else /* Channel2 is used for */
|
|
{
|
|
/* Disable the DMA Stream */
|
|
status = HAL_DMA_Abort(hdac->DMA_Handle2);
|
|
#if defined(DAC_CR_DMAUDRIE2)
|
|
/* Disable the DAC DMA underrun interrupt */
|
|
__HAL_DAC_DISABLE_IT(hdac, DAC_IT_DMAUDR2);
|
|
#endif /* DAC_CR_DMAUDRIE2 */
|
|
}
|
|
|
|
/* Check if DMA Stream effectively disabled */
|
|
if (status != HAL_OK)
|
|
{
|
|
/* Update DAC state machine to error */
|
|
hdac->State = HAL_DAC_STATE_ERROR;
|
|
}
|
|
else
|
|
{
|
|
/* Change DAC state */
|
|
hdac->State = HAL_DAC_STATE_READY;
|
|
}
|
|
|
|
/* Return function status */
|
|
return status;
|
|
}
|
|
|
|
/**
|
|
* @brief Handles DAC interrupt request
|
|
* This function uses the interruption of DMA
|
|
* underrun.
|
|
* @param hdac pointer to a DAC_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DAC.
|
|
* @retval None
|
|
*/
|
|
void HAL_DAC_IRQHandler(DAC_HandleTypeDef *hdac)
|
|
{
|
|
#if defined(DAC_SR_DMAUDR1)
|
|
if (__HAL_DAC_GET_IT_SOURCE(hdac, DAC_IT_DMAUDR1))
|
|
{
|
|
/* Check underrun flag of DAC channel 1 */
|
|
if (__HAL_DAC_GET_FLAG(hdac, DAC_FLAG_DMAUDR1))
|
|
{
|
|
/* Change DAC state to error state */
|
|
hdac->State = HAL_DAC_STATE_ERROR;
|
|
|
|
/* Set DAC error code to chanel1 DMA underrun error */
|
|
SET_BIT(hdac->ErrorCode, HAL_DAC_ERROR_DMAUNDERRUNCH1);
|
|
|
|
/* Clear the underrun flag */
|
|
__HAL_DAC_CLEAR_FLAG(hdac, DAC_FLAG_DMAUDR1);
|
|
|
|
/* Disable the selected DAC channel1 DMA request */
|
|
CLEAR_BIT(hdac->Instance->CR, DAC_CR_DMAEN1);
|
|
|
|
/* Error callback */
|
|
#if (USE_HAL_DAC_REGISTER_CALLBACKS == 1)
|
|
hdac->DMAUnderrunCallbackCh1(hdac);
|
|
#else
|
|
HAL_DAC_DMAUnderrunCallbackCh1(hdac);
|
|
#endif /* USE_HAL_DAC_REGISTER_CALLBACKS */
|
|
}
|
|
}
|
|
#endif /* DAC_SR_DMAUDR1 */
|
|
|
|
#if defined(DAC_SR_DMAUDR2)
|
|
if (__HAL_DAC_GET_IT_SOURCE(hdac, DAC_IT_DMAUDR2))
|
|
{
|
|
/* Check underrun flag of DAC channel 2 */
|
|
if (__HAL_DAC_GET_FLAG(hdac, DAC_FLAG_DMAUDR2))
|
|
{
|
|
/* Change DAC state to error state */
|
|
hdac->State = HAL_DAC_STATE_ERROR;
|
|
|
|
/* Set DAC error code to channel2 DMA underrun error */
|
|
SET_BIT(hdac->ErrorCode, HAL_DAC_ERROR_DMAUNDERRUNCH2);
|
|
|
|
/* Clear the underrun flag */
|
|
__HAL_DAC_CLEAR_FLAG(hdac, DAC_FLAG_DMAUDR2);
|
|
|
|
/* Disable the selected DAC channel2 DMA request */
|
|
CLEAR_BIT(hdac->Instance->CR, DAC_CR_DMAEN2);
|
|
|
|
/* Error callback */
|
|
#if (USE_HAL_DAC_REGISTER_CALLBACKS == 1)
|
|
hdac->DMAUnderrunCallbackCh2(hdac);
|
|
#else
|
|
HAL_DACEx_DMAUnderrunCallbackCh2(hdac);
|
|
#endif /* USE_HAL_DAC_REGISTER_CALLBACKS */
|
|
}
|
|
}
|
|
#endif /* DAC_SR_DMAUDR2 */
|
|
}
|
|
|
|
/**
|
|
* @brief Set the specified data holding register value for DAC channel.
|
|
* @param hdac pointer to a DAC_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DAC.
|
|
* @param Channel The selected DAC channel.
|
|
* This parameter can be one of the following values:
|
|
* @arg DAC_CHANNEL_1: DAC Channel1 selected
|
|
* @arg DAC_CHANNEL_2: DAC Channel2 selected
|
|
* @param Alignment Specifies the data alignment.
|
|
* This parameter can be one of the following values:
|
|
* @arg DAC_ALIGN_8B_R: 8bit right data alignment selected
|
|
* @arg DAC_ALIGN_12B_L: 12bit left data alignment selected
|
|
* @arg DAC_ALIGN_12B_R: 12bit right data alignment selected
|
|
* @param Data Data to be loaded in the selected data holding register.
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_DAC_SetValue(DAC_HandleTypeDef *hdac, uint32_t Channel, uint32_t Alignment, uint32_t Data)
|
|
{
|
|
__IO uint32_t tmp = 0;
|
|
|
|
/* Check the parameters */
|
|
assert_param(IS_DAC_CHANNEL(Channel));
|
|
assert_param(IS_DAC_ALIGN(Alignment));
|
|
assert_param(IS_DAC_DATA(Data));
|
|
|
|
tmp = (uint32_t)hdac->Instance;
|
|
if (Channel == DAC_CHANNEL_1)
|
|
{
|
|
tmp += DAC_DHR12R1_ALIGNMENT(Alignment);
|
|
}
|
|
else
|
|
{
|
|
tmp += DAC_DHR12R2_ALIGNMENT(Alignment);
|
|
}
|
|
|
|
/* Set the DAC channel selected data holding register */
|
|
*(__IO uint32_t *) tmp = Data;
|
|
|
|
/* Return function status */
|
|
return HAL_OK;
|
|
}
|
|
|
|
/**
|
|
* @brief Conversion complete callback in non-blocking mode for Channel1
|
|
* @param hdac pointer to a DAC_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DAC.
|
|
* @retval None
|
|
*/
|
|
__weak void HAL_DAC_ConvCpltCallbackCh1(DAC_HandleTypeDef *hdac)
|
|
{
|
|
/* Prevent unused argument(s) compilation warning */
|
|
UNUSED(hdac);
|
|
|
|
/* NOTE : This function should not be modified, when the callback is needed,
|
|
the HAL_DAC_ConvCpltCallbackCh1 could be implemented in the user file
|
|
*/
|
|
}
|
|
|
|
/**
|
|
* @brief Conversion half DMA transfer callback in non-blocking mode for Channel1
|
|
* @param hdac pointer to a DAC_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DAC.
|
|
* @retval None
|
|
*/
|
|
__weak void HAL_DAC_ConvHalfCpltCallbackCh1(DAC_HandleTypeDef *hdac)
|
|
{
|
|
/* Prevent unused argument(s) compilation warning */
|
|
UNUSED(hdac);
|
|
|
|
/* NOTE : This function should not be modified, when the callback is needed,
|
|
the HAL_DAC_ConvHalfCpltCallbackCh1 could be implemented in the user file
|
|
*/
|
|
}
|
|
|
|
/**
|
|
* @brief Error DAC callback for Channel1.
|
|
* @param hdac pointer to a DAC_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DAC.
|
|
* @retval None
|
|
*/
|
|
__weak void HAL_DAC_ErrorCallbackCh1(DAC_HandleTypeDef *hdac)
|
|
{
|
|
/* Prevent unused argument(s) compilation warning */
|
|
UNUSED(hdac);
|
|
|
|
/* NOTE : This function should not be modified, when the callback is needed,
|
|
the HAL_DAC_ErrorCallbackCh1 could be implemented in the user file
|
|
*/
|
|
}
|
|
|
|
/**
|
|
* @brief DMA underrun DAC callback for channel1.
|
|
* @param hdac pointer to a DAC_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DAC.
|
|
* @retval None
|
|
*/
|
|
__weak void HAL_DAC_DMAUnderrunCallbackCh1(DAC_HandleTypeDef *hdac)
|
|
{
|
|
/* Prevent unused argument(s) compilation warning */
|
|
UNUSED(hdac);
|
|
|
|
/* NOTE : This function should not be modified, when the callback is needed,
|
|
the HAL_DAC_DMAUnderrunCallbackCh1 could be implemented in the user file
|
|
*/
|
|
}
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup DAC_Exported_Functions_Group3 Peripheral Control functions
|
|
* @brief Peripheral Control functions
|
|
*
|
|
@verbatim
|
|
==============================================================================
|
|
##### Peripheral Control functions #####
|
|
==============================================================================
|
|
[..] This section provides functions allowing to:
|
|
(+) Configure channels.
|
|
(+) Set the specified data holding register value for DAC channel.
|
|
|
|
@endverbatim
|
|
* @{
|
|
*/
|
|
|
|
/**
|
|
* @brief Returns the last data output value of the selected DAC channel.
|
|
* @param hdac pointer to a DAC_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DAC.
|
|
* @param Channel The selected DAC channel.
|
|
* This parameter can be one of the following values:
|
|
* @arg DAC_CHANNEL_1: DAC Channel1 selected
|
|
* @arg DAC_CHANNEL_2: DAC Channel2 selected
|
|
* @retval The selected DAC channel data output value.
|
|
*/
|
|
uint32_t HAL_DAC_GetValue(DAC_HandleTypeDef *hdac, uint32_t Channel)
|
|
{
|
|
/* Check the parameters */
|
|
assert_param(IS_DAC_CHANNEL(Channel));
|
|
|
|
/* Returns the DAC channel data output register value */
|
|
if (Channel == DAC_CHANNEL_1)
|
|
{
|
|
return hdac->Instance->DOR1;
|
|
}
|
|
else
|
|
{
|
|
return hdac->Instance->DOR2;
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief Configures the selected DAC channel.
|
|
* @param hdac pointer to a DAC_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DAC.
|
|
* @param sConfig DAC configuration structure.
|
|
* @param Channel The selected DAC channel.
|
|
* This parameter can be one of the following values:
|
|
* @arg DAC_CHANNEL_1: DAC Channel1 selected
|
|
* @arg DAC_CHANNEL_2: DAC Channel2 selected
|
|
* @retval HAL status
|
|
*/
|
|
HAL_StatusTypeDef HAL_DAC_ConfigChannel(DAC_HandleTypeDef *hdac, DAC_ChannelConfTypeDef *sConfig, uint32_t Channel)
|
|
{
|
|
uint32_t tmpreg1;
|
|
uint32_t tmpreg2;
|
|
|
|
/* Check the DAC parameters */
|
|
assert_param(IS_DAC_TRIGGER(sConfig->DAC_Trigger));
|
|
assert_param(IS_DAC_OUTPUT_BUFFER_STATE(sConfig->DAC_OutputBuffer));
|
|
assert_param(IS_DAC_CHANNEL(Channel));
|
|
|
|
/* Process locked */
|
|
__HAL_LOCK(hdac);
|
|
|
|
/* Change DAC state */
|
|
hdac->State = HAL_DAC_STATE_BUSY;
|
|
|
|
/* Get the DAC CR value */
|
|
tmpreg1 = hdac->Instance->CR;
|
|
/* Clear BOFFx, TENx, TSELx, WAVEx and MAMPx bits */
|
|
tmpreg1 &= ~(((uint32_t)(DAC_CR_MAMP1 | DAC_CR_WAVE1 | DAC_CR_TSEL1 | DAC_CR_TEN1 | DAC_CR_BOFF1)) << (Channel & 0x10UL));
|
|
/* Configure for the selected DAC channel: buffer output, trigger */
|
|
/* Set TSELx and TENx bits according to DAC_Trigger value */
|
|
/* Set BOFFx bit according to DAC_OutputBuffer value */
|
|
tmpreg2 = (sConfig->DAC_Trigger | sConfig->DAC_OutputBuffer);
|
|
/* Calculate CR register value depending on DAC_Channel */
|
|
tmpreg1 |= tmpreg2 << (Channel & 0x10UL);
|
|
/* Write to DAC CR */
|
|
hdac->Instance->CR = tmpreg1;
|
|
/* Disable wave generation */
|
|
CLEAR_BIT(hdac->Instance->CR, (DAC_CR_WAVE1 << (Channel & 0x10UL)));
|
|
/* Disable wave generation */
|
|
hdac->Instance->CR &= ~(DAC_CR_WAVE1 << (Channel & 0x10UL));
|
|
|
|
/* Change DAC state */
|
|
hdac->State = HAL_DAC_STATE_READY;
|
|
|
|
/* Process unlocked */
|
|
__HAL_UNLOCK(hdac);
|
|
|
|
/* Return function status */
|
|
return HAL_OK;
|
|
}
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup DAC_Exported_Functions_Group4 Peripheral State and Errors functions
|
|
* @brief Peripheral State and Errors functions
|
|
*
|
|
@verbatim
|
|
==============================================================================
|
|
##### Peripheral State and Errors functions #####
|
|
==============================================================================
|
|
[..]
|
|
This subsection provides functions allowing to
|
|
(+) Check the DAC state.
|
|
(+) Check the DAC Errors.
|
|
|
|
@endverbatim
|
|
* @{
|
|
*/
|
|
|
|
/**
|
|
* @brief return the DAC handle state
|
|
* @param hdac pointer to a DAC_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DAC.
|
|
* @retval HAL state
|
|
*/
|
|
HAL_DAC_StateTypeDef HAL_DAC_GetState(DAC_HandleTypeDef *hdac)
|
|
{
|
|
/* Return DAC handle state */
|
|
return hdac->State;
|
|
}
|
|
|
|
|
|
/**
|
|
* @brief Return the DAC error code
|
|
* @param hdac pointer to a DAC_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DAC.
|
|
* @retval DAC Error Code
|
|
*/
|
|
uint32_t HAL_DAC_GetError(DAC_HandleTypeDef *hdac)
|
|
{
|
|
return hdac->ErrorCode;
|
|
}
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @addtogroup DAC_Exported_Functions
|
|
* @{
|
|
*/
|
|
|
|
/** @addtogroup DAC_Exported_Functions_Group1
|
|
* @{
|
|
*/
|
|
#if (USE_HAL_DAC_REGISTER_CALLBACKS == 1)
|
|
/**
|
|
* @brief Register a User DAC Callback
|
|
* To be used instead of the weak (surcharged) predefined callback
|
|
* @param hdac DAC handle
|
|
* @param CallbackID ID of the callback to be registered
|
|
* This parameter can be one of the following values:
|
|
* @arg @ref HAL_DAC_ERROR_INVALID_CALLBACK DAC Error Callback ID
|
|
* @arg @ref HAL_DAC_CH1_COMPLETE_CB_ID DAC CH1 Complete Callback ID
|
|
* @arg @ref HAL_DAC_CH1_HALF_COMPLETE_CB_ID DAC CH1 Half Complete Callback ID
|
|
* @arg @ref HAL_DAC_CH1_ERROR_ID DAC CH1 Error Callback ID
|
|
* @arg @ref HAL_DAC_CH1_UNDERRUN_CB_ID DAC CH1 UnderRun Callback ID
|
|
* @arg @ref HAL_DAC_CH2_COMPLETE_CB_ID DAC CH2 Complete Callback ID
|
|
* @arg @ref HAL_DAC_CH2_HALF_COMPLETE_CB_ID DAC CH2 Half Complete Callback ID
|
|
* @arg @ref HAL_DAC_CH2_ERROR_ID DAC CH2 Error Callback ID
|
|
* @arg @ref HAL_DAC_CH2_UNDERRUN_CB_ID DAC CH2 UnderRun Callback ID
|
|
* @arg @ref HAL_DAC_MSPINIT_CB_ID DAC MSP Init Callback ID
|
|
* @arg @ref HAL_DAC_MSPDEINIT_CB_ID DAC MSP DeInit Callback ID
|
|
*
|
|
* @param pCallback pointer to the Callback function
|
|
* @retval status
|
|
*/
|
|
HAL_StatusTypeDef HAL_DAC_RegisterCallback(DAC_HandleTypeDef *hdac, HAL_DAC_CallbackIDTypeDef CallbackID,
|
|
pDAC_CallbackTypeDef pCallback)
|
|
{
|
|
HAL_StatusTypeDef status = HAL_OK;
|
|
|
|
if (pCallback == NULL)
|
|
{
|
|
/* Update the error code */
|
|
hdac->ErrorCode |= HAL_DAC_ERROR_INVALID_CALLBACK;
|
|
return HAL_ERROR;
|
|
}
|
|
|
|
/* Process locked */
|
|
__HAL_LOCK(hdac);
|
|
|
|
if (hdac->State == HAL_DAC_STATE_READY)
|
|
{
|
|
switch (CallbackID)
|
|
{
|
|
case HAL_DAC_CH1_COMPLETE_CB_ID :
|
|
hdac->ConvCpltCallbackCh1 = pCallback;
|
|
break;
|
|
case HAL_DAC_CH1_HALF_COMPLETE_CB_ID :
|
|
hdac->ConvHalfCpltCallbackCh1 = pCallback;
|
|
break;
|
|
case HAL_DAC_CH1_ERROR_ID :
|
|
hdac->ErrorCallbackCh1 = pCallback;
|
|
break;
|
|
case HAL_DAC_CH1_UNDERRUN_CB_ID :
|
|
hdac->DMAUnderrunCallbackCh1 = pCallback;
|
|
break;
|
|
case HAL_DAC_CH2_COMPLETE_CB_ID :
|
|
hdac->ConvCpltCallbackCh2 = pCallback;
|
|
break;
|
|
case HAL_DAC_CH2_HALF_COMPLETE_CB_ID :
|
|
hdac->ConvHalfCpltCallbackCh2 = pCallback;
|
|
break;
|
|
case HAL_DAC_CH2_ERROR_ID :
|
|
hdac->ErrorCallbackCh2 = pCallback;
|
|
break;
|
|
case HAL_DAC_CH2_UNDERRUN_CB_ID :
|
|
hdac->DMAUnderrunCallbackCh2 = pCallback;
|
|
break;
|
|
case HAL_DAC_MSPINIT_CB_ID :
|
|
hdac->MspInitCallback = pCallback;
|
|
break;
|
|
case HAL_DAC_MSPDEINIT_CB_ID :
|
|
hdac->MspDeInitCallback = pCallback;
|
|
break;
|
|
default :
|
|
/* Update the error code */
|
|
hdac->ErrorCode |= HAL_DAC_ERROR_INVALID_CALLBACK;
|
|
/* update return status */
|
|
status = HAL_ERROR;
|
|
break;
|
|
}
|
|
}
|
|
else if (hdac->State == HAL_DAC_STATE_RESET)
|
|
{
|
|
switch (CallbackID)
|
|
{
|
|
case HAL_DAC_MSPINIT_CB_ID :
|
|
hdac->MspInitCallback = pCallback;
|
|
break;
|
|
case HAL_DAC_MSPDEINIT_CB_ID :
|
|
hdac->MspDeInitCallback = pCallback;
|
|
break;
|
|
default :
|
|
/* Update the error code */
|
|
hdac->ErrorCode |= HAL_DAC_ERROR_INVALID_CALLBACK;
|
|
/* update return status */
|
|
status = HAL_ERROR;
|
|
break;
|
|
}
|
|
}
|
|
else
|
|
{
|
|
/* Update the error code */
|
|
hdac->ErrorCode |= HAL_DAC_ERROR_INVALID_CALLBACK;
|
|
/* update return status */
|
|
status = HAL_ERROR;
|
|
}
|
|
|
|
/* Release Lock */
|
|
__HAL_UNLOCK(hdac);
|
|
return status;
|
|
}
|
|
|
|
/**
|
|
* @brief Unregister a User DAC Callback
|
|
* DAC Callback is redirected to the weak (surcharged) predefined callback
|
|
* @param hdac DAC handle
|
|
* @param CallbackID ID of the callback to be unregistered
|
|
* This parameter can be one of the following values:
|
|
* @arg @ref HAL_DAC_CH1_COMPLETE_CB_ID DAC CH1 tranfer Complete Callback ID
|
|
* @arg @ref HAL_DAC_CH1_HALF_COMPLETE_CB_ID DAC CH1 Half Complete Callback ID
|
|
* @arg @ref HAL_DAC_CH1_ERROR_ID DAC CH1 Error Callback ID
|
|
* @arg @ref HAL_DAC_CH1_UNDERRUN_CB_ID DAC CH1 UnderRun Callback ID
|
|
* @arg @ref HAL_DAC_CH2_COMPLETE_CB_ID DAC CH2 Complete Callback ID
|
|
* @arg @ref HAL_DAC_CH2_HALF_COMPLETE_CB_ID DAC CH2 Half Complete Callback ID
|
|
* @arg @ref HAL_DAC_CH2_ERROR_ID DAC CH2 Error Callback ID
|
|
* @arg @ref HAL_DAC_CH2_UNDERRUN_CB_ID DAC CH2 UnderRun Callback ID
|
|
* @arg @ref HAL_DAC_MSPINIT_CB_ID DAC MSP Init Callback ID
|
|
* @arg @ref HAL_DAC_MSPDEINIT_CB_ID DAC MSP DeInit Callback ID
|
|
* @arg @ref HAL_DAC_ALL_CB_ID DAC All callbacks
|
|
* @retval status
|
|
*/
|
|
HAL_StatusTypeDef HAL_DAC_UnRegisterCallback(DAC_HandleTypeDef *hdac, HAL_DAC_CallbackIDTypeDef CallbackID)
|
|
{
|
|
HAL_StatusTypeDef status = HAL_OK;
|
|
|
|
/* Process locked */
|
|
__HAL_LOCK(hdac);
|
|
|
|
if (hdac->State == HAL_DAC_STATE_READY)
|
|
{
|
|
switch (CallbackID)
|
|
{
|
|
case HAL_DAC_CH1_COMPLETE_CB_ID :
|
|
hdac->ConvCpltCallbackCh1 = HAL_DAC_ConvCpltCallbackCh1;
|
|
break;
|
|
case HAL_DAC_CH1_HALF_COMPLETE_CB_ID :
|
|
hdac->ConvHalfCpltCallbackCh1 = HAL_DAC_ConvHalfCpltCallbackCh1;
|
|
break;
|
|
case HAL_DAC_CH1_ERROR_ID :
|
|
hdac->ErrorCallbackCh1 = HAL_DAC_ErrorCallbackCh1;
|
|
break;
|
|
case HAL_DAC_CH1_UNDERRUN_CB_ID :
|
|
hdac->DMAUnderrunCallbackCh1 = HAL_DAC_DMAUnderrunCallbackCh1;
|
|
break;
|
|
case HAL_DAC_CH2_COMPLETE_CB_ID :
|
|
hdac->ConvCpltCallbackCh2 = HAL_DACEx_ConvCpltCallbackCh2;
|
|
break;
|
|
case HAL_DAC_CH2_HALF_COMPLETE_CB_ID :
|
|
hdac->ConvHalfCpltCallbackCh2 = HAL_DACEx_ConvHalfCpltCallbackCh2;
|
|
break;
|
|
case HAL_DAC_CH2_ERROR_ID :
|
|
hdac->ErrorCallbackCh2 = HAL_DACEx_ErrorCallbackCh2;
|
|
break;
|
|
case HAL_DAC_CH2_UNDERRUN_CB_ID :
|
|
hdac->DMAUnderrunCallbackCh2 = HAL_DACEx_DMAUnderrunCallbackCh2;
|
|
break;
|
|
case HAL_DAC_MSPINIT_CB_ID :
|
|
hdac->MspInitCallback = HAL_DAC_MspInit;
|
|
break;
|
|
case HAL_DAC_MSPDEINIT_CB_ID :
|
|
hdac->MspDeInitCallback = HAL_DAC_MspDeInit;
|
|
break;
|
|
case HAL_DAC_ALL_CB_ID :
|
|
hdac->ConvCpltCallbackCh1 = HAL_DAC_ConvCpltCallbackCh1;
|
|
hdac->ConvHalfCpltCallbackCh1 = HAL_DAC_ConvHalfCpltCallbackCh1;
|
|
hdac->ErrorCallbackCh1 = HAL_DAC_ErrorCallbackCh1;
|
|
hdac->DMAUnderrunCallbackCh1 = HAL_DAC_DMAUnderrunCallbackCh1;
|
|
hdac->ConvCpltCallbackCh2 = HAL_DACEx_ConvCpltCallbackCh2;
|
|
hdac->ConvHalfCpltCallbackCh2 = HAL_DACEx_ConvHalfCpltCallbackCh2;
|
|
hdac->ErrorCallbackCh2 = HAL_DACEx_ErrorCallbackCh2;
|
|
hdac->DMAUnderrunCallbackCh2 = HAL_DACEx_DMAUnderrunCallbackCh2;
|
|
hdac->MspInitCallback = HAL_DAC_MspInit;
|
|
hdac->MspDeInitCallback = HAL_DAC_MspDeInit;
|
|
break;
|
|
default :
|
|
/* Update the error code */
|
|
hdac->ErrorCode |= HAL_DAC_ERROR_INVALID_CALLBACK;
|
|
/* update return status */
|
|
status = HAL_ERROR;
|
|
break;
|
|
}
|
|
}
|
|
else if (hdac->State == HAL_DAC_STATE_RESET)
|
|
{
|
|
switch (CallbackID)
|
|
{
|
|
case HAL_DAC_MSPINIT_CB_ID :
|
|
hdac->MspInitCallback = HAL_DAC_MspInit;
|
|
break;
|
|
case HAL_DAC_MSPDEINIT_CB_ID :
|
|
hdac->MspDeInitCallback = HAL_DAC_MspDeInit;
|
|
break;
|
|
default :
|
|
/* Update the error code */
|
|
hdac->ErrorCode |= HAL_DAC_ERROR_INVALID_CALLBACK;
|
|
/* update return status */
|
|
status = HAL_ERROR;
|
|
break;
|
|
}
|
|
}
|
|
else
|
|
{
|
|
/* Update the error code */
|
|
hdac->ErrorCode |= HAL_DAC_ERROR_INVALID_CALLBACK;
|
|
/* update return status */
|
|
status = HAL_ERROR;
|
|
}
|
|
|
|
/* Release Lock */
|
|
__HAL_UNLOCK(hdac);
|
|
return status;
|
|
}
|
|
#endif /* USE_HAL_DAC_REGISTER_CALLBACKS */
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @addtogroup DAC_Private_Functions
|
|
* @{
|
|
*/
|
|
|
|
/**
|
|
* @brief DMA conversion complete callback.
|
|
* @param hdma pointer to a DMA_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DMA module.
|
|
* @retval None
|
|
*/
|
|
void DAC_DMAConvCpltCh1(DMA_HandleTypeDef *hdma)
|
|
{
|
|
DAC_HandleTypeDef *hdac = (DAC_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent;
|
|
|
|
#if (USE_HAL_DAC_REGISTER_CALLBACKS == 1)
|
|
hdac->ConvCpltCallbackCh1(hdac);
|
|
#else
|
|
HAL_DAC_ConvCpltCallbackCh1(hdac);
|
|
#endif /* USE_HAL_DAC_REGISTER_CALLBACKS */
|
|
|
|
hdac->State = HAL_DAC_STATE_READY;
|
|
}
|
|
|
|
/**
|
|
* @brief DMA half transfer complete callback.
|
|
* @param hdma pointer to a DMA_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DMA module.
|
|
* @retval None
|
|
*/
|
|
void DAC_DMAHalfConvCpltCh1(DMA_HandleTypeDef *hdma)
|
|
{
|
|
DAC_HandleTypeDef *hdac = (DAC_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent;
|
|
/* Conversion complete callback */
|
|
#if (USE_HAL_DAC_REGISTER_CALLBACKS == 1)
|
|
hdac->ConvHalfCpltCallbackCh1(hdac);
|
|
#else
|
|
HAL_DAC_ConvHalfCpltCallbackCh1(hdac);
|
|
#endif /* USE_HAL_DAC_REGISTER_CALLBACKS */
|
|
}
|
|
|
|
/**
|
|
* @brief DMA error callback
|
|
* @param hdma pointer to a DMA_HandleTypeDef structure that contains
|
|
* the configuration information for the specified DMA module.
|
|
* @retval None
|
|
*/
|
|
void DAC_DMAErrorCh1(DMA_HandleTypeDef *hdma)
|
|
{
|
|
DAC_HandleTypeDef *hdac = (DAC_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent;
|
|
|
|
/* Set DAC error code to DMA error */
|
|
hdac->ErrorCode |= HAL_DAC_ERROR_DMA;
|
|
|
|
#if (USE_HAL_DAC_REGISTER_CALLBACKS == 1)
|
|
hdac->ErrorCallbackCh1(hdac);
|
|
#else
|
|
HAL_DAC_ErrorCallbackCh1(hdac);
|
|
#endif /* USE_HAL_DAC_REGISTER_CALLBACKS */
|
|
|
|
hdac->State = HAL_DAC_STATE_READY;
|
|
}
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
#endif /* DAC */
|
|
|
|
#endif /* HAL_DAC_MODULE_ENABLED */
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|