..
atsam
atsam: Use "communication interface" menu option in Kconfig
2021-03-18 14:22:57 -04:00
atsamd
atsamd: Add support for 25Mhz crystals
2021-06-04 17:48:21 -04:00
avr
avr: Fix Kconfig USB/Serial selection
2021-03-18 14:45:12 -04:00
generic
usb_cdc: Add comments on debugging USB connections via UART
2021-07-04 10:11:02 -04:00
linux
Revert "linux: Raise an error if configuring a pullup when that is not supported"
2021-05-27 11:33:24 -04:00
lpc176x
lpc176x: Add support for serial on UART3 P4.29/P4.28
2021-05-25 12:58:26 -04:00
pru
Makefile: Include debug symbols in the .elf
2021-06-08 19:29:16 -04:00
rp2040
rp2040: implement SPI
2021-07-15 13:30:20 -04:00
simulator
command: Fix handling of buffer passing in args[] on 64bit mcu
2020-10-30 14:04:12 -04:00
stm32
stm32: Add 16KiB bootloader option for STM32F103 ( #4493 )
2021-07-15 14:09:56 -04:00
Kconfig
rp2040: Add initial support for the rp2040 mcu
2021-07-04 10:11:02 -04:00
Makefile
Makefile: Allow CONFIG_HAVE_GPIO_BITBANGING when not CONFIG_HAVE_GPIO_SPI
2021-07-04 10:11:02 -04:00
adccmds.c
…
basecmd.c
stepper: Use a reusable interface to the "move queue"
2020-12-04 16:10:13 -05:00
basecmd.h
stepper: Use a reusable interface to the "move queue"
2020-12-04 16:10:13 -05:00
buttons.c
buttons: initialize mcu buttons based on inverted state
2019-07-05 20:01:07 -04:00
byteorder.h
…
command.c
command: Fix handling of buffer passing in args[] on 64bit mcu
2020-10-30 14:04:12 -04:00
command.h
command: Add command_decode_ptr() helper
2020-10-30 14:04:08 -04:00
compiler.h
…
ctr.h
ctr: Encode negative integers in normal hex notation
2019-08-22 13:06:44 -04:00
debugcmds.c
debugcmds: Remove start/end_group commands
2021-05-07 13:53:47 -04:00
endstop.c
trsync: Introduce new "trigger synchronization" support
2021-06-09 18:58:35 -04:00
gpiocmds.c
gpiocmds: Merge digital output and soft pwm code
2020-12-10 12:06:26 -05:00
i2ccmds.c
command: Add command_decode_ptr() helper
2020-10-30 14:04:08 -04:00
initial_pins.c
initial_pins: Add ability to configure output pins at mcu startup
2019-03-17 20:56:25 -04:00
initial_pins.h
initial_pins: Add ability to configure output pins at mcu startup
2019-03-17 20:56:25 -04:00
lcd_hd44780.c
lcd_st7920: Check CONFIG_MACH_AVR for slow mcus
2021-07-04 10:11:02 -04:00
lcd_st7920.c
lcd_st7920: Check CONFIG_MACH_AVR for slow mcus
2021-07-04 10:11:02 -04:00
neopixel.c
neopixel: Fix neopixel_result message so that it contains an oid
2020-11-05 11:40:34 -05:00
pulse_counter.c
pulse_counter: Use "clock" suffix instead of "time" in commands
2021-04-30 11:40:37 -04:00
pwmcmds.c
pwmcmds: Use move queue for hard PWM
2020-12-04 16:10:13 -05:00
sched.c
sched: Call irq_poll() at start of run_tasks() loop
2021-04-21 19:38:31 -04:00
sched.h
…
sensor_adxl345.c
adxl345: Use "clock" suffix instead of "time" in commands
2021-04-30 11:40:37 -04:00
spi_software.c
spi_software: Remove unused include file
2019-08-17 13:49:03 -04:00
spi_software.h
…
spicmds.c
command: Add command_decode_ptr() helper
2020-10-30 14:04:08 -04:00
spicmds.h
spicmds: Rework spi config commands
2019-08-06 18:56:53 -04:00
stepper.c
trsync: Introduce new "trigger synchronization" support
2021-06-09 18:58:35 -04:00
stepper.h
trsync: Introduce new "trigger synchronization" support
2021-06-09 18:58:35 -04:00
thermocouple.c
…
tmcuart.c
command: Add command_decode_ptr() helper
2020-10-30 14:04:08 -04:00
trsync.c
trsync: Introduce new "trigger synchronization" support
2021-06-09 18:58:35 -04:00
trsync.h
trsync: Introduce new "trigger synchronization" support
2021-06-09 18:58:35 -04:00
698ca1d0ae