Kevin O'Connor fb7fe282c8 klippy: Convert printer_state("shutdown") to an event handler ... Convert all users of the printer_state("shutdown") handler to register a "klippy:shutdown" event handler instead. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>		2019-01-08 10:59:43 -05:00
..
display	menu: allow empty command gcode if action is present	2019-01-07 21:39:50 -05:00
__init__.py	…
ad5206.py	ad5206: Use bus.py helper code for spi	2018-11-21 12:12:31 -05:00
adc_temperature.py	…
bed_mesh.py	bed_mesh: Introduce fade_target option	2018-11-30 11:37:21 -05:00
bed_tilt.py	…
bltouch.py	bltouch: Issue both a "reset" and a "pin_up" after a successful probe	2018-12-16 11:06:46 -05:00
bus.py	i2ccmds: Pass the i2c address as a 7-bit number (0-127)	2019-01-07 20:00:44 -05:00
buttons.py	…
delta_calibrate.py	…
endstop_phase.py	…
fan.py	…
force_move.py	…
gcode_macro.py	…
heater_bed.py	heater: take a gcode_id when setting up a heater (#1028)	2019-01-02 17:44:02 -05:00
heater_fan.py	…
homing_override.py	…
idle_timeout.py	…
mcp4451.py	i2ccmds: Pass the i2c address as a 7-bit number (0-127)	2019-01-07 20:00:44 -05:00
mcp4728.py	mcp4728: Add initial support for the mcp4728 i2c dac chip	2019-01-02 18:17:56 -05:00
multi_pin.py	…
output_pin.py	…
pid_calibrate.py	…
probe.py	bltouch: Add initial support for a bltouch "extras" module	2018-11-30 11:34:20 -05:00
quad_gantry_level.py	…
query_endstops.py	…
replicape.py	…
respond.py	respond: An extra for sending messages to the printer host. (#1053)	2019-01-02 17:45:35 -05:00
servo.py	…
spi_temperature.py	…
static_digital_output.py	…
statistics.py	…
sx1509.py	i2ccmds: Pass the i2c address as a 7-bit number (0-127)	2019-01-07 20:00:44 -05:00
temperature_fan.py	…
thermistor.py	thermistor: Avoid divide by zero error if min_temp=-273.15	2019-01-04 12:47:37 -05:00
tmc2130.py	tmc2130: Use bus.py helper code for spi	2018-11-21 12:12:31 -05:00
tmc2208.py	tmc2208: error raise fixed for rx/tx mcu check	2018-12-27 11:44:41 -05:00
tmc2660.py	tmc2660: error and whitespace fixes	2018-12-27 11:44:41 -05:00
verify_heater.py	klippy: Convert printer_state("shutdown") to an event handler	2019-01-08 10:59:43 -05:00
virtual_sdcard.py	klippy: Convert printer_state("shutdown") to an event handler	2019-01-08 10:59:43 -05:00
z_tilt.py	z_tilt: unresolved reference fixed	2019-01-08 08:44:25 -05:00