133 lines
2.2 KiB
INI
133 lines
2.2 KiB
INI
# This file contains common pin mappings for a Fysetc F6 board with
|
|
# TMC2208 stepper motor drivers. To use this config, the firmware
|
|
# should be compiled for the AVR atmega2560.
|
|
|
|
# See the example.cfg file for a description of available parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PF0
|
|
dir_pin: PF1
|
|
enable_pin: !PD7
|
|
step_distance: .0125
|
|
endstop_pin: ^PK1
|
|
position_endstop: 0
|
|
position_max: 235
|
|
homing_speed: 50
|
|
|
|
[tmc2208 stepper_x]
|
|
uart_pin: PG3
|
|
tx_pin: PJ2
|
|
microsteps: 16
|
|
run_current: 0.7
|
|
hold_current: 0.7
|
|
stealthchop_threshold: 250
|
|
|
|
[stepper_y]
|
|
step_pin: PF6
|
|
dir_pin: PF7
|
|
enable_pin: !PF2
|
|
step_distance: .0125
|
|
endstop_pin: ^PJ1
|
|
position_endstop: 0
|
|
position_max: 238
|
|
homing_speed: 50
|
|
|
|
[tmc2208 stepper_y]
|
|
uart_pin: PJ3
|
|
tx_pin: PJ4
|
|
microsteps: 16
|
|
run_current: 0.7
|
|
hold_current: 0.7
|
|
stealthchop_threshold: 250
|
|
|
|
[stepper_z]
|
|
step_pin: PL6
|
|
dir_pin: !PL1
|
|
enable_pin: !PF4
|
|
step_distance: .0025
|
|
endstop_pin: ^PB6
|
|
position_endstop: 0
|
|
position_max: 250
|
|
position_min: -1
|
|
|
|
[tmc2208 stepper_z]
|
|
uart_pin: PE2
|
|
tx_pin: PE6
|
|
microsteps: 16
|
|
run_current: 0.7
|
|
hold_current: 0.7
|
|
stealthchop_threshold: 100
|
|
|
|
[extruder]
|
|
step_pin: PA4
|
|
dir_pin: !PA6
|
|
enable_pin: !PA2
|
|
step_distance: .0025
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PE3
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PK4
|
|
control: pid
|
|
pid_Kp: 29.662
|
|
pid_Ki: 2.326
|
|
pid_Kd: 94.549
|
|
min_temp: 0
|
|
max_temp: 320
|
|
|
|
[tmc2208 extruder]
|
|
uart_pin: PJ5
|
|
tx_pin: PJ6
|
|
microsteps: 16
|
|
run_current: 0.9
|
|
hold_current: 0.9
|
|
stealthchop_threshold: 250
|
|
|
|
[heater_bed]
|
|
heater_pin: PH5
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PK7
|
|
control: pid
|
|
pid_kp: 74.536
|
|
pid_ki: 1.206
|
|
pid_kd: 1151.587
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
#fan for printed model FAN0
|
|
[fan]
|
|
pin: PL5
|
|
|
|
#fan for hotend FAN1
|
|
[heater_fan my_nozzle_fan]
|
|
pin: PL4
|
|
shutdown_speed: 0
|
|
fan_speed: 0.9
|
|
|
|
#fan for control board FAN2
|
|
[heater_fan my_control_fan]
|
|
pin: PL3
|
|
shutdown_speed: 0
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
# "RepRapDiscount 128x64 Full Graphic Smart Controller" type displays
|
|
#[display]
|
|
#lcd_type: st7920
|
|
#cs_pin: PH1
|
|
#sclk_pin: PA1
|
|
#sid_pin: PH0
|
|
#encoder_pins: ^PC6, ^PC4
|
|
#click_pin: ^!PC2
|
|
#
|
|
#[static_digital_output beeper]
|
|
#pins: !PC0
|