93 lines
1.5 KiB
INI
93 lines
1.5 KiB
INI
# Test config for bed screws tool with bltouch
|
|
[stepper_x]
|
|
step_pin: PF0
|
|
dir_pin: PF1
|
|
enable_pin: !PD7
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^PE5
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: PF6
|
|
dir_pin: !PF7
|
|
enable_pin: !PF2
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^PJ1
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: PL3
|
|
dir_pin: PL1
|
|
enable_pin: !PK0
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: probe:z_virtual_endstop
|
|
position_max: 200
|
|
|
|
[extruder]
|
|
step_pin: PA4
|
|
dir_pin: PA6
|
|
enable_pin: !PA2
|
|
microsteps: 16
|
|
rotation_distance: 33.5
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PB4
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PK5
|
|
control: pid
|
|
pid_Kp: 22.2
|
|
pid_Ki: 1.08
|
|
pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
[heater_bed]
|
|
heater_pin: PH5
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PK6
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[bltouch]
|
|
sensor_pin: PC7
|
|
control_pin: PC5
|
|
z_offset: 1.15
|
|
samples: 3
|
|
sample_retract_dist: 2.
|
|
samples_result: median
|
|
|
|
[bed_mesh]
|
|
mesh_min: 10,10
|
|
mesh_max: 180,180
|
|
|
|
[mcu]
|
|
serial: /dev/ttyACM0
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
[screws_tilt_adjust]
|
|
screw1: 10,30
|
|
screw1_name: front left screw
|
|
screw2: 155,30
|
|
screw2_name: front right screw
|
|
screw3: 155,190
|
|
screw3_name: rear right screw
|
|
screw4: 10,190
|
|
screw4_name: read left screw
|
|
horizontal_move_z: 10.
|
|
speed: 50.
|
|
screw_thread: CW-M3
|