3diy
/
klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
klipper/test/klippy
History
Kevin O'Connor 5d26c2a08e gcode_arcs: Add back in support for E moves in absolute extrude mode 
This reverts commit 43fa41c1af.

The above commit disabled absolute extrude moves because it was
unclear if the code would work properly when an M221 extrude factor or
G92 offset was in use.  However, since the calculation is done
relative to the raw E position and is sent as a raw E position to
gcode.cmd_G1() these modes should not matter.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 		2020-06-04 15:25:17 -04:00
..
bed_screws.cfg bed_screws: Add a helper tool for leveling bed screws 2019-02-24 00:49:47 -05:00
bed_screws.test test: Rename atmega2560-16mhz.config to atmega2560.config 2019-03-22 12:36:18 -04:00
bltouch.cfg test: update sample configs and test configs with new bed_mesh options 2020-01-09 14:14:13 -05:00
bltouch.test test: Rename atmega2560-16mhz.config to atmega2560.config 2019-03-22 12:36:18 -04:00
commands.test test: Fix commands.test so RESTART is run last 2020-04-28 22:53:12 -04:00
delta.test test: Rename atmega2560-16mhz.config to atmega2560.config 2019-03-22 12:36:18 -04:00
delta_calibrate.cfg test: Add new delta_calibrate test case 2019-12-05 14:48:52 -05:00
delta_calibrate.test test: Add new delta_calibrate test case 2019-12-05 14:48:52 -05:00
dual_carriage.cfg gcode: Remove builtin T0/T1/T2/... command support 2019-12-10 14:24:32 -05:00
dual_carriage.test test: Rename atmega2560-16mhz.config to atmega2560.config 2019-03-22 12:36:18 -04:00
extruders.cfg extruder_stepper: Initial support for synchronized extruder steppers 2020-01-06 11:03:05 -05:00
extruders.test stepper: No need to pass stepper_kinematics to set_step_dist() 2020-03-28 10:06:02 -04:00
gcode_arcs.cfg test: Add initial test case for gcode_arcs support 2019-09-13 12:05:15 -04:00
gcode_arcs.test gcode_arcs: Add back in support for E moves in absolute extrude mode 2020-06-04 15:25:17 -04:00
macros.cfg gcode_macro: Parse variable_X parameters using ast.literal_eval() 2019-06-07 19:33:31 -04:00
macros.test test: Add a macros.test test case for testing gcode_macro 2019-06-04 09:50:30 -04:00
manual_stepper.cfg manual_stepper: Add support for moves with acceleration 2019-03-03 13:38:10 -05:00
manual_stepper.test test: Rename atmega2560-16mhz.config to atmega2560.config 2019-03-22 12:36:18 -04:00
move.gcode winch: Add experimental support for cable winch kinematics 2018-12-24 11:38:59 -05:00
multi_z.cfg
…
multi_z.test test: Rename atmega2560-16mhz.config to atmega2560.config 2019-03-22 12:36:18 -04:00
out_of_bounds.test test: Rename atmega2560-16mhz.config to atmega2560.config 2019-03-22 12:36:18 -04:00
polar.test polar: Add initial support for multiple bed rotations 2019-06-28 10:00:40 -04:00
printers.test config: Add example config printer-makergear-m2-2016.cfg 2020-06-04 12:01:30 -04:00
quad_gantry_level.test test: Flush moves in quad_gantry_level and z_tilt_adjust tests 2019-06-12 15:36:32 -04:00
rotary_delta_calibrate.cfg rotary_delta: Initial support for rotary delta kinematics 2020-01-06 11:52:42 -05:00
rotary_delta_calibrate.test rotary_delta: Initial support for rotary delta kinematics 2020-01-06 11:52:42 -05:00
screws_tilt_adjust.cfg test: update sample configs and test configs with new bed_mesh options 2020-01-09 14:14:13 -05:00
screws_tilt_adjust.test test: Rename atmega2560-16mhz.config to atmega2560.config 2019-03-22 12:36:18 -04:00
temperature.cfg adc_temperature: Add builtin definition for PT1000 sensors 2020-03-05 11:46:01 -05:00
temperature.test test: Rename atmega2560-16mhz.config to atmega2560.config 2019-03-22 12:36:18 -04:00
tmc.cfg tmc2209: Add support for sensorless homing 2019-08-19 12:05:09 -04:00
tmc.test tmc: Configure "intpol" field from TMCMicrostepHelper 2019-06-28 16:59:26 -04:00
z_tilt.cfg test: Add quad_gantry_level and z_tilt_adjust test cases 2019-06-12 13:49:27 -04:00
z_tilt.test test: Flush moves in quad_gantry_level and z_tilt_adjust tests 2019-06-12 15:36:32 -04:00
z_virtual_endstop.cfg test: update sample configs and test configs with new bed_mesh options 2020-01-09 14:14:13 -05:00
z_virtual_endstop.test test: Rename atmega2560-16mhz.config to atmega2560.config 2019-03-22 12:36:18 -04:00