115 lines
2.6 KiB
INI
115 lines
2.6 KiB
INI
# This file contains common pin mappings for the Two Trees Sapphire
|
|
# Plus V1.1 (SP-5) printer (Robin Nano 1.2, all 2225 drivers at 32 microsteps).
|
|
|
|
# INSTRUCTIONS FOR COMPILING
|
|
# To use this config, the firmware should be compiled for the STM32F103.
|
|
# When running "make menuconfig", enable "extra low-level configuration setup",
|
|
# select the 28KiB bootloader, serial (on USART3 PB11/PB10) to use USB communication
|
|
# or serial (on USART1 PA10/PA9) to use direct UART connection with Raspberry trough wifi pins.
|
|
# Set "GPIO pins to set at micro-controller startup" to "!PC6,!PD13" to turn off display at startup.
|
|
|
|
# INSTRUCTIONS FOR FLASHING, THE SCRIPT IS COMPULSORY OR IT WON'T WORK!!!
|
|
# Note that the "make flash" command does not work with the Robin Nano!
|
|
# After running "make", run the following command in one row FROM THE KLIPPER FOLDER:
|
|
# ./scripts/update_mks_robin.py out/klipper.bin out/Robin_nano35.bin
|
|
# Copy the file out/Robin_nano35.bin (if you can't find the file the script was not executed)
|
|
# to an SD card and then restart the printer with that SD card.
|
|
# If you removed the LCD screen rename the file to "Robin_nano43.bin" for correct flashing.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PE3
|
|
dir_pin: !PE2
|
|
enable_pin: !PE4
|
|
microsteps: 32
|
|
rotation_distance: 40
|
|
endstop_pin: !PA15
|
|
position_endstop: 0
|
|
position_max: 300
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: PE0
|
|
dir_pin: !PB9
|
|
enable_pin: !PE1
|
|
microsteps: 32
|
|
rotation_distance: 40
|
|
endstop_pin: !PA12
|
|
position_endstop: 300
|
|
position_max: 300
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: PB5
|
|
dir_pin: !PB4
|
|
enable_pin: !PB8
|
|
microsteps: 32
|
|
rotation_distance: 8
|
|
endstop_pin: !PA11
|
|
position_endstop: 0
|
|
position_max: 340
|
|
|
|
[stepper_z1]
|
|
step_pin: PA6
|
|
dir_pin: !PA1
|
|
enable_pin: !PA3
|
|
microsteps: 32
|
|
rotation_distance: 8
|
|
|
|
[extruder]
|
|
step_pin: PD6
|
|
dir_pin: !PD3
|
|
enable_pin: !PB3
|
|
microsteps: 32
|
|
gear_ratio: 50:17
|
|
rotation_distance: 23.52
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PC3
|
|
sensor_type: EPCOS 100K B57560G104F # Stock
|
|
sensor_pin: PC1
|
|
min_temp: 0
|
|
max_temp: 250
|
|
control: pid
|
|
pid_Kp: 17.48
|
|
pid_Ki: 1.32
|
|
pid_Kd: 57.81
|
|
|
|
[heater_bed]
|
|
heater_pin: PA0
|
|
sensor_type: EPCOS 100K B57560G104F # Stock
|
|
sensor_pin: PC0
|
|
min_temp: 0
|
|
max_temp: 130
|
|
control: pid
|
|
pid_Kp: 325.10
|
|
pid_Ki: 63.35
|
|
pid_Kd: 417.10
|
|
|
|
[heater_fan extruder]
|
|
pin: PB0
|
|
|
|
[fan]
|
|
pin: PB1
|
|
|
|
[mcu]
|
|
serial: /dev/ttyUSB0
|
|
restart_method: command
|
|
|
|
[printer]
|
|
kinematics: corexy
|
|
max_velocity: 250
|
|
max_accel: 4500
|
|
max_z_velocity: 15
|
|
max_z_accel: 100
|
|
|
|
[bed_screws]
|
|
screw1: 35,35
|
|
screw2: 275,35
|
|
screw3: 275,275
|
|
screw4: 35,275
|
|
|
|
[static_digital_output reset_display]
|
|
pins: !PC6, !PD13
|