| .. |
|
display
|
menu: Correction for the resume option appears when the toolhead is not printing (#1077)
|
2019-01-05 19:11:03 -05:00 |
|
__init__.py
|
…
|
|
|
ad5206.py
|
ad5206: Use bus.py helper code for spi
|
2018-11-21 12:12:31 -05:00 |
|
adc_temperature.py
|
…
|
|
|
bed_mesh.py
|
bed_mesh: Introduce fade_target option
|
2018-11-30 11:37:21 -05:00 |
|
bed_tilt.py
|
bed_tilt: Do not automatically run G28 on BED_TILT_CALIBRATE
|
2018-10-22 11:26:01 -04:00 |
|
bltouch.py
|
bltouch: Issue both a "reset" and a "pin_up" after a successful probe
|
2018-12-16 11:06:46 -05:00 |
|
bus.py
|
bus: Set all SPI CS pins high before first config_spi message
|
2019-01-04 22:26:34 -05:00 |
|
buttons.py
|
…
|
|
|
delta_calibrate.py
|
delta_calibrate: Do not automatically run G28 on DELTA_CALIBRATE
|
2018-10-22 11:26:01 -04:00 |
|
endstop_phase.py
|
tmc2660: Add endstop phase detection functionality to TMC2660 extra (#816)
|
2018-10-24 16:01:12 -04:00 |
|
fan.py
|
…
|
|
|
force_move.py
|
…
|
|
|
gcode_macro.py
|
…
|
|
|
heater_bed.py
|
heater: take a gcode_id when setting up a heater (#1028)
|
2019-01-02 17:44:02 -05:00 |
|
heater_fan.py
|
…
|
|
|
homing_override.py
|
…
|
|
|
idle_timeout.py
|
idle_timeout: Add printing/ready/idle tracking
|
2018-10-28 18:39:45 -04:00 |
|
mcp4451.py
|
mcp4451: Minor update - remove unnecessary mcu import
|
2018-11-24 00:36:49 -05:00 |
|
mcp4728.py
|
mcp4728: Add initial support for the mcp4728 i2c dac chip
|
2019-01-02 18:17:56 -05:00 |
|
multi_pin.py
|
…
|
|
|
output_pin.py
|
…
|
|
|
pid_calibrate.py
|
pid_calibrate: Add some comments on the calibration methodology
|
2018-10-19 22:40:11 -04:00 |
|
probe.py
|
bltouch: Add initial support for a bltouch "extras" module
|
2018-11-30 11:34:20 -05:00 |
|
quad_gantry_level.py
|
…
|
|
|
query_endstops.py
|
…
|
|
|
replicape.py
|
replicape: Use bus.py helper code for spi
|
2018-11-21 12:12:31 -05:00 |
|
respond.py
|
respond: An extra for sending messages to the printer host. (#1053)
|
2019-01-02 17:45:35 -05:00 |
|
servo.py
|
servo: This patch create ability to enable/disable attached servo. (#880)
|
2018-11-14 09:38:09 -05:00 |
|
spi_temperature.py
|
spi_temperature: Use bus.py helper code for spi
|
2018-11-21 12:12:31 -05:00 |
|
static_digital_output.py
|
…
|
|
|
statistics.py
|
…
|
|
|
sx1509.py
|
sx1509: Relax restrictions on SX1509 pins (#836)
|
2018-10-30 18:08:12 -04:00 |
|
temperature_fan.py
|
…
|
|
|
thermistor.py
|
thermistor: Avoid divide by zero error if min_temp=-273.15
|
2019-01-04 12:47:37 -05:00 |
|
tmc2130.py
|
tmc2130: Use bus.py helper code for spi
|
2018-11-21 12:12:31 -05:00 |
|
tmc2208.py
|
tmc2208: error raise fixed for rx/tx mcu check
|
2018-12-27 11:44:41 -05:00 |
|
tmc2660.py
|
tmc2660: error and whitespace fixes
|
2018-12-27 11:44:41 -05:00 |
|
verify_heater.py
|
…
|
|
|
virtual_sdcard.py
|
gcode: process_batch() should execute commands atomically
|
2018-10-28 18:39:45 -04:00 |
|
z_tilt.py
|
…
|
|
ffbb4198c1