3diy
/
klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
klipper/src
History
Kevin O'Connor 5f2cb5436c linux: Disable hardware pwm when it is set to zero 
Only write "1" to the "enable" file when a non-zero pwm width is
requested.  Write "0" to the "enable" file when a zero pwm width is
requested.

This fixes a problem on the replicape servo lines that prevented them
from being fully disabled.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 		2020-07-20 22:18:28 -04:00
..
atsam Kconfig: Add a new CONFIG_HAVE_STRICT_TIMING build definition 2020-05-31 14:57:06 -04:00
atsamd Kconfig: Add a new CONFIG_HAVE_STRICT_TIMING build definition 2020-05-31 14:57:06 -04:00
avr Kconfig: Add a new CONFIG_HAVE_STRICT_TIMING build definition 2020-05-31 14:57:06 -04:00
generic generic: Minor header cleanup to generic/irq.h 2020-06-07 21:18:04 -04:00
linux linux: Disable hardware pwm when it is set to zero 2020-07-20 22:18:28 -04:00
lpc176x lpc176x: Fix spi mode bits 2020-07-10 16:08:18 -04:00
pru Kconfig: Add a new CONFIG_HAVE_STRICT_TIMING build definition 2020-05-31 14:57:06 -04:00
simulator simulator: Wrap code to 80 columns 2019-02-27 14:20:15 -05:00
stm32 stm32: Improved CAN support for STM32 (#2976) 2020-06-24 18:59:38 -04:00
Kconfig Kconfig: Only show the "usb ids" menu if low-level options are enabled 2020-05-31 21:05:04 -04:00
Makefile initial_pins: Only build when CONFIG_HAVE_GPIO is enabled 2019-07-24 01:09:45 -04:00
adccmds.c adccmds: Run gpio_adc_setup() before oid_alloc() 2019-01-13 11:03:30 -05:00
basecmd.c basecmd: No need for finalize_config command to send "config" response 2020-02-20 12:01:21 -05:00
basecmd.h spicmds: Rework spi config commands 2019-08-06 18:56:53 -04:00
buttons.c buttons: initialize mcu buttons based on inverted state 2019-07-05 20:01:07 -04:00
byteorder.h
…
command.c
…
command.h buildcommands: Match DECL_X names to the actual C macro names 2019-08-22 13:26:30 -04:00
compiler.h
…
ctr.h ctr: Encode negative integers in normal hex notation 2019-08-22 13:06:44 -04:00
debugcmds.c debugcmds: Add support for reading/writing 32bit values 2019-02-07 11:50:14 -05:00
endstop.c endstop: Rename mcu end_stop commands to endstop 2019-07-12 08:10:53 -04:00
gpiocmds.c gpiocmds: Specify soft pwm duration in clock ticks 2019-05-26 11:09:32 -04:00
i2ccmds.c avr: implement i2c_read 2020-01-13 22:29:50 -05:00
initial_pins.c initial_pins: Add ability to configure output pins at mcu startup 2019-03-17 20:56:25 -04:00
initial_pins.h initial_pins: Add ability to configure output pins at mcu startup 2019-03-17 20:56:25 -04:00
lcd_hd44780.c lcd_hd44780: Only calibrate cmd_wait_ticks on mcus with strict timing 2020-05-31 14:57:06 -04:00
lcd_st7920.c lcd_st7920: Only calibrate wait ticks on mcus with strict timing 2020-05-31 14:57:06 -04:00
neopixel.c neopixel: Make sure there is a minimum low duration after a long pulse 2020-04-21 13:12:56 -04:00
pwmcmds.c pwmcmds: allow 16-bit resolution 2019-04-05 19:02:48 -04:00
sched.c
…
sched.h
…
spi_software.c spi_software: Remove unused include file 2019-08-17 13:49:03 -04:00
spi_software.h spi_software: Implementation of software spi 2019-02-13 11:52:20 -05:00
spicmds.c spicmds: Rework spi config commands 2019-08-06 18:56:53 -04:00
spicmds.h spicmds: Rework spi config commands 2019-08-06 18:56:53 -04:00
stepper.c stepper: Make toggling the step gpio after timer read conditional 2020-05-31 14:57:06 -04:00
stepper.h
…
thermocouple.c thermocouple: Define thermocouple types using enumerations 2019-03-17 19:38:18 -04:00
tmcuart.c tmcuart: Fix typo in function name 2019-09-01 14:56:09 -04:00