5.8 KiB
This document covers recent software changes to the config file that are not backwards compatible. It is a good idea to review this document when upgrading the Klipper software.
All dates in this document are approximate.
Changes
20191210: The builtin T0, T1, T2, ... commands have been removed. The extruder activate_gcode and deactivate_gcode config options have been removed. If these commands (and scripts) are needed then define individual [gcode_macro T0] style macros that call the ACTIVATE_EXTRUDER command.
20191210: Support for the M206 command has been removed. Replace with calls to SET_GCODE_OFFSET. If support for M206 is needed, add a [gcode_macro M206] config section that calls SET_GCODE_OFFSET. (For example "SET_GCODE_OFFSET Z=-{params.Z}".)
20191202: Support for the undocumented "S" parameter of the "G4" command has been removed. Replace any occurrences of S with the standard "P" parameter (the delay specified in milliseconds).
20191126: The USB names have changed on micro-controllers with native USB support. They now use a unique chip id by default (where available). If an "mcu" config section uses a "serial" setting that starts with "/dev/serial/by-id/" then it may be necessary to update the config. Run "ls /dev/serial/by-id/*" in an ssh terminal to determine the new id.
20191121: The pressure_advance_lookahead_time parameter has been removed. See example.cfg for alternate configuration settings.
20191112: The tmc stepper driver virtual enable capability is now automatically enabled if the stepper does not have a dedicated stepper enable pin. Remove references to tmcXXXX:virtual_enable from the config. The ability to control multiple pins in the stepper enable_pin config has been removed. If multiple pins are needed then use a multi_pin config section.
20191107: The primary extruder config section must be specified as "extruder" and may no longer be specified as "extruder0". Gcode command templates that query the extruder status are now accessed via "{printer.extruder}".
20191021: Klipper v0.8.0 released
20191003: The move_to_previous option in [safe_z_homing] now defaults to False. (It was effectively False prior to 20190918.)
20190918: The zhop option in [safe_z_homing] is always re-applied after Z axis homing completed. This might need users to update custom scripts based on this module.
20190806: The SET_NEOPIXEL command has been renamed to SET_LED.
20190726: The mcp4728 digital-to-analog code has changed. The default i2c_address is now 0x60 and the voltage reference is now relative to the mcp4728's internal 2.048 volt reference.
20190710: The z_hop option was removed from the [firmware_retract] config section. The z_hop support was incomplete and could cause incorrect behavior with several common slicers.
20190710: The optional parameters of the PROBE_ACCURACY command have changed. It may be necessary to update any macros or scripts that use that command.
20190628: All configuration options have been removed from the [skew_correction] section. Configuration for skew_correction is now done via the SET_SKEW gcode. See skew_correction.md for recommended usage.
20190607: The "variable_X" parameters of gcode_macro (along with the VALUE parameter of SET_GCODE_VARIABLE) are now parsed as Python literals. If a value needs to be assigned a string then wrap the value in quotes so that it is evaluated as a string.
20190606: The "samples", "samples_result", and "sample_retract_dist" config options have been moved to the "probe" config section. These options are no longer supported in the "delta_calibrate", "bed_tilt", "bed_mesh", "screws_tilt_adjust", "z_tilt", or "quad_gantry_level" config sections.
20190528: The magic "status" variable in gcode_macro template evaluation has been renamed to "printer".
20190520: The SET_GCODE_OFFSET command has changed; update any g-code macros accordingly. The command will no longer apply the requested offset to the next G1 command. The old behavior may be approximated by using the new "MOVE=1" parameter.
20190404: The Python host software packages were updated. Users will need to rerun the ~/klipper/scripts/install-octopi.sh script (or otherwise upgrade the python dependencies if not using a standard OctoPi installation).
20190404: The i2c_bus and spi_bus parameters (in various config sections) now take a bus name instead of a number.
20190404: The sx1509 config parameters have changed. The 'address' parameter is now 'i2c_address' and it must be specified as a decimal number. Where 0x3E was previously used, specify 62.
20190328: The min_speed value in [temperature_fan] config will now be respected and the fan will always run at this speed or higher in PID mode.
20190322: The default value for "driver_HEND" in [tmc2660] config sections was changed from 6 to 3. The "driver_VSENSE" field was removed (it is now automatically calculated from run_current).
20190310: The [controller_fan] config section now always takes a name (such as [controller_fan my_controller_fan]).
20190308: The "driver_BLANK_TIME_SELECT" field in [tmc2130] and [tmc2208] config sections has been renamed to "driver_TBL".
20190308: The [tmc2660] config section has changed. A new sense_resistor config parameter must now be provided. The meaning of several of the driver_XXX parameters has changed.
20190228: Users of SPI or I2C on SAMD21 boards must now specify the bus pins via a [samd_sercom] config section.
20190224: The bed_shape option has been removed from bed_mesh. The radius option has been renamed to bed_radius. Users with round beds should supply the bed_radius and round_probe_count options.
20190107: The i2c_address parameter in the mcp4451 config section changed. This is a common setting on Smoothieboards. The new value is half the old value (88 should be changed to 44, and 90 should be changed to 45).
20181220: Klipper v0.7.0 released