3diy
/
klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
klipper/docs
History
Kevin O'Connor ca7dd8bfd4 docs: Update Pressure_Advance.md - don't set square_corner_velocity=0 
Setting the square corner velocity to zero would cause stuttering
during the test if a bed mesh is in effect.  It's possible to get the
desired effect by reducing the square corner velocity and setting the
pressure advance lookahead time instead.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 		2018-10-25 11:43:03 -04:00
..
img docs: Add Delta_Calibrate.md guide with "enhanced delta calibration" 2018-09-25 13:48:46 -04:00
prints delta_calibrate: Initial support for enhanced delta calibration 2018-09-25 13:48:46 -04:00
Bootloaders.md docs: Updates to stm32f103 benchmarks 2018-10-11 10:57:24 -04:00
CONTRIBUTING.md docs: Add a CONTRIBUTING document 2017-12-24 12:33:01 -05:00
Code_Overview.md docs: Add a section with micro-controller porting tips to Code_Overview.md 2018-07-11 14:40:39 -04:00
Config_checks.md docs: Add an Endstop_Phase.md document 2018-10-16 13:09:49 -04:00
Contact.md docs: Expand on why it is important to provide the log in Contact.md 2018-07-08 20:30:35 -04:00
Debugging.md docs: Fix SAM4E8E benchmark test revision 2018-10-22 11:21:43 -04:00
Delta_Calibrate.md delta_calibrate: Do not automatically run G28 on DELTA_CALIBRATE 2018-10-22 11:26:01 -04:00
Endstop_Phase.md tmc2660: Add endstop phase detection functionality to TMC2660 extra (#816) 2018-10-24 16:01:12 -04:00
FAQ.md docs: Add a "Lost communication with MCU" section to the FAQ 2018-10-09 11:22:28 -04:00
Features.md docs: Update SAM4E8E benchmarks 2018-10-22 11:18:55 -04:00
G-Codes.md bed_mesh: Do not automatically run G28 on BED_MESH_CALIBRATE / BED_MESH_MAP 2018-10-22 11:26:01 -04:00
Installation.md gcode: Send proactive state messages 2018-09-12 21:31:27 -04:00
Kinematics.md docs: Minor change to wording of junction speeds 2018-08-03 15:48:07 -04:00
MCU_Commands.md basecmd: Rename get_status to get_clock 2018-05-29 10:57:29 -04:00
Overview.md docs: Add an Endstop_Phase.md document 2018-10-16 13:09:49 -04:00
Pressure_Advance.md docs: Update Pressure_Advance.md - don't set square_corner_velocity=0 2018-10-25 11:43:03 -04:00
Protocol.md docs: Replace get_status example with get_clock in Protocol.md 2018-10-20 11:53:32 -04:00
README.md docs: Improve documentation for those starting in docs/ 2017-04-27 16:05:26 -04:00
Releases.md docs: Update release notes for v0.6.0 release 2018-03-31 14:04:39 -04:00
beaglebone.md pru: Disable ADC reading directly from the PRU 2018-06-27 12:10:25 -04:00
developer-certificate-of-origin docs: Add a CONTRIBUTING document 2017-12-24 12:33:01 -05:00
issue_template.md docs: Add github issue template 2018-01-31 14:30:05 -05:00
stm32f1.md docs: Update stm32f1.md - usb is now supported. 2018-10-22 13:22:58 -04:00

README.md

Welcome to the Klipper documentation. The overview document is a good starting point.