3diy
/
klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
klipper/src
History
clearchris 009d14fc3e stm32: adc for new stm32f0 common code (#2120) 
Derived from stm32/adc.c and stm32f0/adc.c with additional changes.

Tested on Monoprice Mini Delta (malyan) stm32f070xb board.

Signed-off-by: Chris Lombardi <clearchris@hotmail.com>
 		2019-11-05 10:08:32 -05:00
..
atsam flash_usb: Pass -t $CONFIG_MCU to flash_usb on all targets 2019-10-26 18:48:00 -04:00
atsamd flash_usb: Pass -t $CONFIG_MCU to flash_usb on all targets 2019-10-26 18:48:00 -04:00
avr avr: List 20Mhz option below 16Mhz option in Kconfig 2019-09-30 10:05:02 -04:00
generic armcm_boot: Use armcm_main() instead of main() to start board code 2019-10-24 11:16:10 -04:00
linux spicmds: Rework spi config commands 2019-08-06 18:56:53 -04:00
lpc176x flash_usb: Pass -t $CONFIG_MCU to flash_usb on all targets 2019-10-26 18:48:00 -04:00
pru pru: The TMR_CNT is cleared by writing all ones 2019-03-31 13:48:50 -04:00
simulator simulator: Wrap code to 80 columns 2019-02-27 14:20:15 -05:00
stm32 stm32: adc for new stm32f0 common code (#2120) 2019-11-05 10:08:32 -05:00
stm32f0 stm32f0: Rename internal build symbol from MACH_STM32F0 to MACH_STM32F0_HAL 2019-10-23 21:16:35 -04:00
Kconfig stm32: Support stm32f042 build from stm32/ directory 2019-10-23 21:34:48 -04:00
Makefile initial_pins: Only build when CONFIG_HAVE_GPIO is enabled 2019-07-24 01:09:45 -04:00
adccmds.c adccmds: Run gpio_adc_setup() before oid_alloc() 2019-01-13 11:03:30 -05:00
basecmd.c spicmds: Rework spi config commands 2019-08-06 18:56:53 -04:00
basecmd.h spicmds: Rework spi config commands 2019-08-06 18:56:53 -04:00
buttons.c buttons: initialize mcu buttons based on inverted state 2019-07-05 20:01:07 -04:00
byteorder.h byteorder: Add a header file defining common byteswap functions 2018-05-21 09:44:40 -04:00
command.c command: Wait to send ack until after processing commands 2018-05-28 10:43:40 -04:00
command.h buildcommands: Match DECL_X names to the actual C macro names 2019-08-22 13:26:30 -04:00
compiler.h compiler.h: Check if __aligned and __section macros are already defined 2016-06-13 23:18:59 -04:00
ctr.h ctr: Encode negative integers in normal hex notation 2019-08-22 13:06:44 -04:00
debugcmds.c debugcmds: Add support for reading/writing 32bit values 2019-02-07 11:50:14 -05:00
endstop.c endstop: Rename mcu end_stop commands to endstop 2019-07-12 08:10:53 -04:00
gpiocmds.c gpiocmds: Specify soft pwm duration in clock ticks 2019-05-26 11:09:32 -04:00
i2ccmds.c bus: Change bus parameter in config_spi/config_i2c 2019-04-04 18:29:31 -04:00
initial_pins.c initial_pins: Add ability to configure output pins at mcu startup 2019-03-17 20:56:25 -04:00
initial_pins.h initial_pins: Add ability to configure output pins at mcu startup 2019-03-17 20:56:25 -04:00
lcd_hd44780.c lcd_hd44780: Add micro-controller code for the HD44780 LCD chip 2018-03-06 11:30:34 -05:00
lcd_st7920.c lcd_st7920: Add brief delay around gpio toggle calls on fast MCUs 2019-08-10 11:45:15 -04:00
neopixel.c neopixel: Rework timing so that it works on AVR micro-controllers 2019-08-07 15:37:05 -04:00
pwmcmds.c pwmcmds: allow 16-bit resolution 2019-04-05 19:02:48 -04:00
sched.c sched: Force sched_try_shutdown to be inlined 2018-10-13 11:47:00 -04:00
sched.h pru: Support config_reset command to manually reset mcu 2017-09-03 23:16:38 -04:00
spi_software.c spi_software: Remove unused include file 2019-08-17 13:49:03 -04:00
spi_software.h spi_software: Implementation of software spi 2019-02-13 11:52:20 -05:00
spicmds.c spicmds: Rework spi config commands 2019-08-06 18:56:53 -04:00
spicmds.h spicmds: Rework spi config commands 2019-08-06 18:56:53 -04:00
stepper.c stepper: Don't update SF_LAST_DIR if SF_NEED_RESET 2019-07-12 07:54:24 -04:00
stepper.h stepper: Introduce stepper_get_position command and remove from endstop.c 2017-03-09 14:54:52 -05:00
thermocouple.c thermocouple: Define thermocouple types using enumerations 2019-03-17 19:38:18 -04:00
tmcuart.c tmcuart: Fix typo in function name 2019-09-01 14:56:09 -04:00