116 lines
2.1 KiB
INI
116 lines
2.1 KiB
INI
# This file contains common pin mappings for Longer LK4 Pro.
|
|
# To use this config, the firmware should be compiled for the AVR
|
|
# atmega2560 (though other AVR chips are also possible).
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: ar54
|
|
dir_pin: !ar55
|
|
enable_pin: !ar38
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^!ar3
|
|
position_endstop: 0
|
|
position_max: 235
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: ar60
|
|
dir_pin: ar61
|
|
enable_pin: !ar56
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^!ar14
|
|
position_endstop: 0
|
|
position_max: 235
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: ar46
|
|
dir_pin: !ar48
|
|
enable_pin: !ar62
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: ^!ar35
|
|
# Uncomment for BLTouch
|
|
# endstop_pin: probe:z_virtual_endstop
|
|
position_endstop: 0.5
|
|
position_max: 250
|
|
|
|
# Uncomment this section for BLTouch
|
|
|
|
# [homing_override]
|
|
# axes: z
|
|
# set_position_z: 0.0
|
|
# gcode:
|
|
# G90
|
|
# G0 Z5 F600
|
|
# G28 X0 Y0
|
|
# G0 X143 Y137 F3600
|
|
# G28 Z0
|
|
# G0 Z5 F600
|
|
|
|
# [bltouch]
|
|
# According this follow mapping :
|
|
# https://arduiblog.com/2020/06/22/installation-dun-bltouch-sur-lalfawise-u30-pro/
|
|
# & see "Branchement" paragraph & picture
|
|
# sensor_pin: ^ar35
|
|
# control_pin: ar7
|
|
# If you use this fang : https://www.thingiverse.com/thing:3603067
|
|
# you can use this follow values for x & y offset
|
|
# x_offset: -28
|
|
# y_offset: -26
|
|
# and test this z_offset
|
|
# z_offset: 1.56
|
|
|
|
# [bed_mesh]
|
|
# mesh_min: 16,16
|
|
# mesh_max: 201,200
|
|
# probe_count: 4,3
|
|
|
|
[extruder]
|
|
step_pin: ar26
|
|
dir_pin: !ar28
|
|
enable_pin: !ar24
|
|
microsteps: 16
|
|
rotation_distance: 34.5576
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: ar10
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: analog13
|
|
control: pid
|
|
pid_Kp: 22.2
|
|
pid_Ki: 1.08
|
|
pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
[filament_switch_sensor filament_sensor]
|
|
switch_pin: ^!ar2
|
|
|
|
[heater_bed]
|
|
heater_pin: ar8
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: analog14
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[fan]
|
|
pin: ar9
|
|
|
|
[mcu]
|
|
serial: /dev/ttyUSB0
|
|
pin_map: arduino
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
# Klipper doesn't able to working display at this time
|