218 lines
4.1 KiB
INI
218 lines
4.1 KiB
INI
# This file contains common pin mappings for the Fysetc S6 v2 board.
|
|
# To use this config, the firmware should be compiled for the STM32F446.
|
|
# When calling "menuconfig", enable "extra low-level configuration setup"
|
|
# and select the "12MHz crystal" as clock reference
|
|
# For flashing, write the compiled klipper.bin to memory location 0x08000000
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PE11
|
|
dir_pin: PE10
|
|
enable_pin: !PE9
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: PB14 # PA1 for X-max
|
|
position_endstop: 0
|
|
position_max: 200
|
|
|
|
[stepper_y]
|
|
step_pin: PD8
|
|
dir_pin: PB12
|
|
enable_pin: !PD9
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: PB13 # PA2 for Y-max
|
|
position_endstop: 0
|
|
position_max: 200
|
|
|
|
[stepper_z]
|
|
step_pin: PD14
|
|
dir_pin: PD13
|
|
enable_pin: !PD15
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: PA0 # PA3 for Z-max
|
|
position_endstop: 0
|
|
position_max: 400
|
|
|
|
[extruder]
|
|
step_pin: PD5
|
|
dir_pin: !PD6
|
|
enable_pin: !PD4
|
|
microsteps: 16
|
|
rotation_distance: 33.500
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PB3
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC0
|
|
control: pid
|
|
pid_Kp: 22
|
|
pid_Ki: 1.08
|
|
pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 260
|
|
|
|
#[extruder1]
|
|
#step_pin: PE6
|
|
#dir_pin: !PC13
|
|
#enable_pin: !PE5
|
|
#heater_pin: PB4
|
|
#sensor_pin: PC1
|
|
|
|
#[extruder2]
|
|
#step_pin: PE2
|
|
#dir_pin: !PE4
|
|
#enable_pin: !PE3
|
|
#heater_pin: PB15
|
|
#sensor_pin: PC2
|
|
|
|
[heater_bed]
|
|
heater_pin: PC8
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC3
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
#fan for printed model FAN0
|
|
[fan]
|
|
pin: PB0
|
|
|
|
#fan for hotend FAN1
|
|
#[heater_fan my_nozzle_fan]
|
|
#pin: PB1
|
|
#shutdown_speed: 1
|
|
|
|
#fan for control board FAN2
|
|
#[heater_fan my_control_fan]
|
|
#pin: PB2
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
|
|
########################################
|
|
# TMC UART configuration
|
|
########################################
|
|
|
|
#[tmc2208 stepper_x]
|
|
#uart_pin: PE8
|
|
#run_current: 0.8
|
|
#hold_current: 0.5
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2208 stepper_y]
|
|
#uart_pin: PC4
|
|
#run_current: 0.8
|
|
#hold_current: 0.5
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2208 stepper_z]
|
|
#uart_pin: PD12
|
|
#run_current: 0.8
|
|
#hold_current: 0.5
|
|
#stealthchop_threshold: 100
|
|
|
|
#[tmc2208 extruder]
|
|
#uart_pin: PA15
|
|
#run_current: 0.8
|
|
#hold_current: 0.5
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2208 extruder1]
|
|
#uart_pin: PC5
|
|
#run_current: 0.8
|
|
#hold_current: 0.5
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2208 extruder2]
|
|
#uart_pin: PE0
|
|
#run_current: 0.8
|
|
#hold_current: 0.5
|
|
#stealthchop_threshold: 250
|
|
|
|
|
|
########################################
|
|
# TMC SPI configuration
|
|
########################################
|
|
|
|
#[tmc2130 stepper_x]
|
|
#spi_bus: spi4
|
|
#cs_pin: PE7
|
|
#diag1_pin: PB14
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2130 stepper_y]
|
|
#spi_bus: spi4
|
|
#cs_pin: PE15
|
|
#diag1_pin: PB13
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2130 stepper_z]
|
|
#spi_bus: spi4
|
|
#cs_pin: PD10
|
|
#diag1_pin: PA0
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2130 extruder]
|
|
#spi_bus: spi4
|
|
#cs_pin: PD7
|
|
#diag1_pin: PA3
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2130 extruder1]
|
|
#spi_bus: spi4
|
|
#cs_pin: PC14
|
|
#diag1_pin: PA2
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2130 extruder2]
|
|
#spi_bus: spi4
|
|
#cs_pin: PC15
|
|
#diag1_pin: PA1
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 250
|
|
|
|
|
|
########################################
|
|
# EXP1 / EXP2 (display) pins
|
|
########################################
|
|
|
|
[board_pins]
|
|
aliases:
|
|
# EXP1 header
|
|
EXP1_1=PC9, EXP1_2=PA8,
|
|
EXP1_3=PC11, EXP1_4=PD2,
|
|
EXP1_5=PC10, EXP1_6=PC12, # Slot in the socket on this side
|
|
EXP1_7=PD0, EXP1_8=PD1,
|
|
EXP1_9=<GND>, EXP1_10=<5V>,
|
|
|
|
# EXP2 header
|
|
EXP2_1=PA6, EXP2_2=PA5,
|
|
EXP2_3=PC6, EXP2_4=PA4,
|
|
EXP2_5=PC7, EXP2_6=PA7, # Slot in the socket on this side
|
|
EXP2_7=PB10, EXP2_8=<RST>,
|
|
EXP2_9=<GND>, EXP2_10=<5V>
|
|
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|