264 lines
4.8 KiB
INI
264 lines
4.8 KiB
INI
# This file contains common pin mappings for the 9 stepper motor
|
|
# "flymaker flyboard FLYF407ZG" board from creative3dprinter.com. To
|
|
# use this config, the firmware should be compiled for the STM32F407
|
|
# with a "32KiB bootloader".
|
|
|
|
# The "make flash" command does not work on the FLYBOARD. Instead,
|
|
# after running "make", copy the generated "out/klipper.bin" file to a
|
|
# file named "firmware.bin" on an SD card and then restart the FLYBOARD
|
|
# with that SD card.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PB9
|
|
dir_pin: PE0
|
|
enable_pin: !PE1
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: PC3
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: PB8
|
|
dir_pin: PG11
|
|
enable_pin: !PG12
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: PF2
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: PA8
|
|
dir_pin: PD6
|
|
enable_pin: !PD7
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: PF0
|
|
position_endstop: 0.5
|
|
position_max: 200
|
|
|
|
[extruder]
|
|
step_pin: PC7
|
|
dir_pin: PD3
|
|
enable_pin: !PD4
|
|
microsteps: 16
|
|
rotation_distance: 33.500
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PF7 # Heat0
|
|
sensor_pin: PA0 # T1 Header
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
control: pid
|
|
pid_Kp: 22.2
|
|
pid_Ki: 1.08
|
|
pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 350
|
|
|
|
#[extruder1]
|
|
#step_pin: PC6
|
|
#dir_pin: PA15
|
|
#enable_pin: !PD0
|
|
#heater_pin: PF6 # Heat1
|
|
#sensor_pin: PC1 # T2
|
|
#...
|
|
|
|
#[extruder2]
|
|
#step_pin: PD15
|
|
#dir_pin: PG7
|
|
#enable_pin: !PG8
|
|
#heater_pin: PE6 # Heat2
|
|
#sensor_pin: PC0 # T3
|
|
#...
|
|
|
|
#[extruder3]
|
|
#step_pin: PD14
|
|
#dir_pin: PG4
|
|
#enable_pin: !PG5
|
|
#heater_pin: PE5 # Heat3
|
|
#sensor_pin: PF10 # T4
|
|
#...
|
|
|
|
#[extruder4]
|
|
#step_pin: PD13
|
|
#dir_pin: PD11
|
|
#enable_pin: !PG2
|
|
#heater_pin: PE4 # Heat4
|
|
#sensor_pin: PF5 # T5
|
|
#...
|
|
|
|
#[extruder4]
|
|
#step_pin: PD12
|
|
#dir_pin: PD8
|
|
#enable_pin: !PD9
|
|
#heater_pin: PE3 # Heat5
|
|
#sensor_pin: PF4 # T6
|
|
#...
|
|
|
|
[heater_bed]
|
|
heater_pin: PE2
|
|
sensor_pin: PF3 # T0
|
|
sensor_type: ATC Semitec 104GT-2
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 200
|
|
|
|
[fan]
|
|
pin: PF8
|
|
|
|
[heater_fan fan1]
|
|
pin: PF9
|
|
|
|
#[heater_fan fan2]
|
|
#pin: PA2
|
|
|
|
#[heater_fan fan3]
|
|
#pin: PA1
|
|
|
|
#[heater_fan fan4]
|
|
#pin: PE13
|
|
|
|
#[heater_fan fan5]
|
|
#pin: PB11
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
|
|
|
[printer]
|
|
kinematics: corexy
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
|
|
########################################
|
|
# TMC2208 configuration
|
|
########################################
|
|
|
|
#[tmc2208 stepper_x]
|
|
#uart_pin: PG13
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2208 stepper_y]
|
|
#uart_pin: PG10
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2208 stepper_z]
|
|
#uart_pin: PD5
|
|
#run_current: 0.650
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2208 extruder]
|
|
#uart_pin: PD1
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2208 extruder1]
|
|
#uart_pin: PA14
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2208 extruder2]
|
|
#uart_pin: PG6
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2208 extruder3]
|
|
#uart_pin: PG3
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2208 extruder4]
|
|
#uart_pin: PD10
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2208 extruder5]
|
|
#uart_pin: PB12
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
|
|
|
|
########################################
|
|
# TMC2130 configuration
|
|
########################################
|
|
|
|
#[tmc2130 stepper_x]
|
|
#cs_pin: PG13
|
|
##diag1_pin: PC3
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2130 stepper_y]
|
|
#cs_pin: PG10
|
|
##diag1_pin: PF2
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2130 stepper_z]
|
|
#cs_pin: PBD5
|
|
##diag1_pin: PF0
|
|
#run_current: 0.650
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2130 extruder]
|
|
#cs_pin: PD1
|
|
##diag1_pin: PE15
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2130 extruder1]
|
|
#cs_pin: PA14
|
|
##diag1_pin: PE10
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2130 extruder2]
|
|
#cs_pin: PG6
|
|
##diag1_pin: PC15
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2130 extruder3]
|
|
#cs_pin: PG3
|
|
##diag1_pin: PC15
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2130 extruder4]
|
|
#cs_pin: PD10
|
|
##diag1_pin: PC15
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2130 extruder5]
|
|
#cs_pin: PB12
|
|
##diag1_pin: PC15
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
|
|
|
|
########################################
|
|
# EXP1 / EXP2 (display) pins
|
|
########################################
|
|
|
|
[board_pins]
|
|
aliases:
|
|
# EXP1 header
|
|
EXP1_1=PB10, EXP1_3=PE14, EXP1_5=PE10, EXP1_7=PE8, EXP1_9=<GND>,
|
|
EXP1_2=PE15, EXP1_4=PE12, EXP1_6=PE9, EXP1_8=PE7, EXP1_10=<5V>,
|
|
# EXP2 header
|
|
EXP2_1=PB14, EXP2_3=PC5, EXP2_5=PC4, EXP2_7=PB2, EXP2_9=<GND>,
|
|
EXP2_2=PB13, EXP2_4=PF11, EXP2_6=PB15, EXP2_8=<RST>, EXP2_10=<GND>
|
|
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi2"
|
|
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|