..
avr
command: Add command_find_and_dispatch() helper
2018-05-28 10:43:39 -04:00
generic
serialqueue: Limit message transmission to available receive buffer size
2018-05-28 11:12:30 -04:00
linux
command: Add command_find_and_dispatch() helper
2018-05-28 10:43:39 -04:00
lpc176x
lpc176x: Add a dummy "make flash" command to advise users on how to flash
2018-05-25 11:58:23 -04:00
pru
command: Wait to send ack until after processing commands
2018-05-28 10:43:40 -04:00
sam3x8e
stepper: Introduce and use gpio_out_toggle_noirq()
2018-05-15 17:09:11 -04:00
simulator
stepper: Introduce and use gpio_out_toggle_noirq()
2018-05-15 17:09:11 -04:00
stm32f1
stepper: Introduce and use gpio_out_toggle_noirq()
2018-05-15 17:09:11 -04:00
Kconfig
lpc176x: Add initial support for LPC176x processors
2018-05-25 11:52:13 -04:00
Makefile
lcd_hd44780: Add micro-controller code for the HD44780 LCD chip
2018-03-06 11:30:34 -05:00
adccmds.c
adccmds: Continue to query analog inputs after a shutdown
2017-10-12 11:59:27 -04:00
basecmd.c
basecmd: Rename get_status to get_clock
2018-05-29 10:57:29 -04:00
basecmd.h
pru: Support config_reset command to manually reset mcu
2017-09-03 23:16:38 -04:00
byteorder.h
byteorder: Add a header file defining common byteswap functions
2018-05-21 09:44:40 -04:00
command.c
command: Wait to send ack until after processing commands
2018-05-28 10:43:40 -04:00
command.h
command: Wait to send ack until after processing commands
2018-05-28 10:43:40 -04:00
compiler.h
compiler.h: Check if __aligned and __section macros are already defined
2016-06-13 23:18:59 -04:00
ctr.h
build: Avoid linker magic in compile_time_request.c unique id generation
2017-05-26 12:32:02 -04:00
debugcmds.c
debugcmds: Move debugging commands from basecmd.c to new file
2017-05-15 14:02:59 -04:00
endstop.c
endstop: Eliminate end_stop_set_oversample command
2017-10-12 11:59:27 -04:00
gpiocmds.c
stepper: Introduce and use gpio_out_toggle_noirq()
2018-05-15 17:09:11 -04:00
lcd_hd44780.c
lcd_hd44780: Add micro-controller code for the HD44780 LCD chip
2018-03-06 11:30:34 -05:00
lcd_st7920.c
lcd_st7920: Add micro-controller code for the ST7920 LCD chip
2018-03-06 11:30:30 -05:00
pwmcmds.c
gpiocmds: Allow the start value for a pin to differ from the default_value
2017-10-12 11:59:27 -04:00
sched.c
sched: Interrupts must be disabled during setjmp() call
2017-12-21 12:54:33 -05:00
sched.h
pru: Support config_reset command to manually reset mcu
2017-09-03 23:16:38 -04:00
spicmds.c
spicmds: Rework SPI message transmission
2018-05-07 09:10:34 -04:00
stepper.c
stepper: Introduce and use gpio_out_toggle_noirq()
2018-05-15 17:09:11 -04:00
stepper.h
stepper: Introduce stepper_get_position command and remove from endstop.c
2017-03-09 14:54:52 -05:00