128 lines
2.6 KiB
INI
128 lines
2.6 KiB
INI
# Klipper firmware config file for Anycubic 4Max. To use this config,
|
|
# the firmware should be compiled for the AVR atmega2560.
|
|
|
|
# See the example.cfg file for a description of available parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: ar54
|
|
dir_pin: ar55
|
|
enable_pin: !ar38
|
|
step_distance: .0125
|
|
endstop_pin: ^!ar3
|
|
position_min: -2
|
|
position_endstop: -2
|
|
position_max: 205
|
|
homing_speed: 60.0
|
|
|
|
[stepper_y]
|
|
step_pin: ar60
|
|
dir_pin: ar61
|
|
enable_pin: !ar56
|
|
step_distance: .0125
|
|
endstop_pin: ^!ar14
|
|
position_endstop: 0
|
|
position_max: 215
|
|
homing_speed: 60.0
|
|
|
|
[stepper_z]
|
|
step_pin: ar46
|
|
dir_pin: ar48
|
|
enable_pin: !ar62
|
|
step_distance: .0025
|
|
endstop_pin: ^!ar18
|
|
position_endstop: 0.5
|
|
position_max: 305
|
|
homing_speed: 8.0
|
|
|
|
[extruder]
|
|
step_pin: ar26
|
|
dir_pin: ar28
|
|
enable_pin: !ar24
|
|
step_distance: 0.010354
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
max_extrude_only_distance: 2000
|
|
heater_pin: ar10
|
|
sensor_type: ATC Semitec 104GT-2
|
|
sensor_pin: analog13
|
|
control: pid
|
|
pid_kp: 27.725
|
|
pid_ki: 1.224
|
|
pid_kd: 156.991
|
|
min_temp: 0
|
|
max_temp: 300
|
|
|
|
[heater_bed]
|
|
heater_pin: ar8
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: analog14
|
|
control: pid
|
|
pid_kp: 73.735
|
|
pid_ki: 1.437
|
|
pid_kd: 945.653
|
|
min_temp: 0
|
|
max_temp: 110
|
|
|
|
[fan]
|
|
pin: ar9
|
|
kick_start_time: 1.0
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-Silicon_Labs_CP2102_USB_to_UART_Bridge_Controller_0001-if00-port0
|
|
pin_map: arduino
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 1200
|
|
max_accel: 1500
|
|
max_z_velocity: 40
|
|
max_z_accel: 60
|
|
|
|
[heater_fan extruder_fan]
|
|
pin: ar44
|
|
|
|
[heater_fan stepstick_fan]
|
|
pin: ar7
|
|
kick_start_time: 1.0
|
|
|
|
[display]
|
|
lcd_type: st7920
|
|
cs_pin: ar16
|
|
sclk_pin: ar23
|
|
sid_pin: ar17
|
|
encoder_pins: ^ar31, ^ar33
|
|
click_pin: ^!ar35
|
|
kill_pin: ^!ar41
|
|
|
|
[filament_switch_sensor e0_sensor]
|
|
switch_pin: ar19
|
|
|
|
[gcode_macro START_PRINT]
|
|
gcode:
|
|
M117 Starting...
|
|
G90 ; absolute positioning
|
|
M107 ; start with the fan off
|
|
G28 ; Home
|
|
G0 X5 Y5 F4500 ; Go to front
|
|
G0 Z0.3 ; Drop to bed
|
|
G92 E0 ; zero the extruded length
|
|
G1 Y40 E15 F500 ; Extrude 15mm of filament in a 4cm line
|
|
G92 E0 ; zero the extruded length
|
|
G1 Y80 F4000 ; Quickly wipe away from the filament line
|
|
G1 Z1 ; Raise and begin printing.
|
|
M117 Printing...
|
|
|
|
[gcode_macro END_PRINT]
|
|
gcode:
|
|
M117 End printing.
|
|
G91 ; relative positioning
|
|
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle to release some of the pressure
|
|
G1 Z+5 E-2 F1000 ;move Z up a bit and extract a bit more
|
|
G90 ; absolute positioning
|
|
G1 X0 F2000 ; move X to min endstops so the head is out of the way
|
|
G1 Y200 F2000 ; Move Y to the back
|
|
m104 S0 ; turn hotend heating off
|
|
M140 S0 ; turn bed heating off
|
|
M107 ; turn fan off
|
|
M84 ; steppers off
|