3diy
/
klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
klipper/src
History
Kevin O'Connor b77375e955 lpc176x: Reset LPC_UART0->FDR when using serial 
The popular "LPC17xx-DFU-Bootloader" alters the LPC_UART0->FDR
register, so be sure to reset it back to its default when using serial
in Klipper.

Reported by @b-vs.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 		2019-07-10 20:00:58 -04:00
..
atsam atsam: Add support for "timer" controlled hardware pwm pins 2019-06-02 10:59:33 -04:00
atsamd atsamd: Add build support for SAMD21E15 chip 2019-06-01 13:43:37 -04:00
avr avr: Simplify spi mode setting 2019-05-07 23:02:20 -04:00
generic armcm_timer: Unify udelay() implementation 2019-06-09 20:27:57 -04:00
linux linux: add support for Linux hardware PWM 2019-04-05 19:06:15 -04:00
lpc176x lpc176x: Reset LPC_UART0->FDR when using serial 2019-07-10 20:00:58 -04:00
pru pru: The TMR_CNT is cleared by writing all ones 2019-03-31 13:48:50 -04:00
simulator simulator: Wrap code to 80 columns 2019-02-27 14:20:15 -05:00
stm32f0 armcm_timer: Unify udelay() implementation 2019-06-09 20:27:57 -04:00
stm32f1 armcm_timer: Unify udelay() implementation 2019-06-09 20:27:57 -04:00
Kconfig stm32f0: New target STM32F0 added. 2019-03-24 12:10:11 -04:00
Makefile initial_pins: Add ability to configure output pins at mcu startup 2019-03-17 20:56:25 -04:00
adccmds.c adccmds: Run gpio_adc_setup() before oid_alloc() 2019-01-13 11:03:30 -05:00
basecmd.c command: Always pass a string to the DECL_CONSTANT() macro 2019-03-17 19:38:18 -04:00
basecmd.h pru: Support config_reset command to manually reset mcu 2017-09-03 23:16:38 -04:00
buttons.c buttons: initialize mcu buttons based on inverted state 2019-07-05 20:01:07 -04:00
byteorder.h byteorder: Add a header file defining common byteswap functions 2018-05-21 09:44:40 -04:00
command.c command: Wait to send ack until after processing commands 2018-05-28 10:43:40 -04:00
command.h msgproto: Convert static strings to a more generic enumeration system 2019-03-17 19:38:18 -04:00
compiler.h
…
ctr.h command: Support evaluating C expressions in DECL_CONSTANT() 2019-03-17 19:38:18 -04:00
debugcmds.c debugcmds: Add support for reading/writing 32bit values 2019-02-07 11:50:14 -05:00
endstop.c endstop: Use "pin_value" instead of "pin" when querying endstop state 2019-03-19 10:48:33 -04:00
gpiocmds.c gpiocmds: Specify soft pwm duration in clock ticks 2019-05-26 11:09:32 -04:00
i2ccmds.c bus: Change bus parameter in config_spi/config_i2c 2019-04-04 18:29:31 -04:00
initial_pins.c initial_pins: Add ability to configure output pins at mcu startup 2019-03-17 20:56:25 -04:00
initial_pins.h initial_pins: Add ability to configure output pins at mcu startup 2019-03-17 20:56:25 -04:00
lcd_hd44780.c lcd_hd44780: Add micro-controller code for the HD44780 LCD chip 2018-03-06 11:30:34 -05:00
lcd_st7920.c lcd_st7920: Use a longer delay at the start of each command/data 2018-06-22 23:47:09 -04:00
pwmcmds.c pwmcmds: allow 16-bit resolution 2019-04-05 19:02:48 -04:00
sched.c sched: Force sched_try_shutdown to be inlined 2018-10-13 11:47:00 -04:00
sched.h pru: Support config_reset command to manually reset mcu 2017-09-03 23:16:38 -04:00
spi_software.c spi_software: Minor simplification to spi_software_prepare() 2019-05-22 11:40:30 -04:00
spi_software.h spi_software: Implementation of software spi 2019-02-13 11:52:20 -05:00
spicmds.c bus: Change bus parameter in config_spi/config_i2c 2019-04-04 18:29:31 -04:00
spicmds.h thermocouple: Add initial support for common SPI temperature sensing chips 2018-07-24 11:16:05 -04:00
stepper.c stepper: Fix reset_step_clock corruption due to bitset typo 2019-03-19 20:57:17 -04:00
stepper.h stepper: Introduce stepper_get_position command and remove from endstop.c 2017-03-09 14:54:52 -05:00
thermocouple.c thermocouple: Define thermocouple types using enumerations 2019-03-17 19:38:18 -04:00
tmcuart.c pins: Add support for pull down resistors 2019-02-27 11:13:21 -05:00