| .. |
|
Kconfig
|
stm32: F429 shall use 168Mhz to allow easy USB clock configuration
|
2021-02-19 12:14:19 -05:00 |
|
Makefile
|
canbus: Move high-level CAN code to new src/generic/canbus.c
|
2021-02-02 15:24:11 -05:00 |
|
adc.c
|
stm32: Support for STM32F401 (#3853)
|
2021-01-31 19:41:53 -05:00 |
|
can.c
|
stm32: Add STM32F429 variant (#3926)
|
2021-02-18 20:12:32 -05:00 |
|
chipid.c
|
stm32: Enable chipid as usb serial number
|
2019-11-25 19:30:31 -05:00 |
|
gpio.c
|
stm32: Define PGx pins on stm32f103
|
2019-11-02 11:35:27 -04:00 |
|
gpio.h
|
stm32: Add support for SPI1 and SPI3 busses
|
2019-08-31 19:55:30 -04:00 |
|
i2c.c
|
stm32: add support for i2c read
|
2020-05-05 11:44:19 -04:00 |
|
internal.h
|
stm32: Initial support for stm32f2 (#3001)
|
2020-06-23 10:52:15 -04:00 |
|
serial.c
|
stm32: Fix typo that broke selection of alternate serial port pin
|
2020-02-09 12:01:43 -05:00 |
|
spi.c
|
stm32: Add support for spi bus on stm32f407 pins PI2,PI3,PI1
|
2021-02-12 17:32:54 -05:00 |
|
stm32f0.c
|
stm32: Adding support for STM32F031x6 (#3871)
|
2021-02-03 12:23:17 -05:00 |
|
stm32f0_adc.c
|
stm32: Support reading chip based temperature sensor on stm32f0
|
2020-10-29 11:55:06 -04:00 |
|
stm32f0_i2c.c
|
stm32f0: Initial support for i2c on stm32f0
|
2019-11-14 15:54:28 -05:00 |
|
stm32f0_serial.c
|
stm32: Adding support for STM32F031x6 (#3871)
|
2021-02-03 12:23:17 -05:00 |
|
stm32f0_timer.c
|
stm32: Initial support for stm32f070
|
2019-10-23 21:19:03 -04:00 |
|
stm32f1.c
|
stm32f1: Fix for using 16MHz external crystal (#3814)
|
2021-01-24 10:24:11 -05:00 |
|
stm32f4.c
|
stm32: Optimize stm32f401 peripheral clock
|
2021-02-19 12:19:32 -05:00 |
|
usbfs.c
|
stm32: Initial support for stm32f070
|
2019-10-23 21:19:03 -04:00 |
|
usbotg.c
|
stm32: Wait for setup complete to enable ep0 rx in usbotg.c
|
2020-05-03 12:00:47 -04:00 |
|
watchdog.c
|
…
|
|
267a2f3a38