| .. |
|
atsam
|
atsam: Support reading chip based temperature sensor on sam4e
|
2020-10-29 11:55:06 -04:00 |
|
atsamd
|
atsamd: Fix bug in sercom_pads mapping on samd21 in sercom.c
|
2021-02-01 10:55:38 -05:00 |
|
avr
|
Kconfig: Add a new CONFIG_HAVE_STRICT_TIMING build definition
|
2020-05-31 14:57:06 -04:00 |
|
generic
|
canbus: Call can_notify_rx() at startup so low-level code does not need to
|
2021-02-09 18:51:03 -05:00 |
|
linux
|
ds18b20: new module for 1-wire temperature sensor (#3462)
|
2021-02-02 14:34:56 -05:00 |
|
lpc176x
|
lpc176x: Fix spi mode bits
|
2020-07-10 16:08:18 -04:00 |
|
pru
|
pru: Request the host not send more than 496 bytes to the pru
|
2021-02-12 11:23:29 -05:00 |
|
simulator
|
command: Fix handling of buffer passing in args[] on 64bit mcu
|
2020-10-30 14:04:12 -04:00 |
|
stm32
|
stm32: Optimize stm32f401 peripheral clock
|
2021-02-19 12:19:32 -05:00 |
|
Kconfig
|
Kconfig: Only show the "usb ids" menu if low-level options are enabled
|
2020-05-31 21:05:04 -04:00 |
|
Makefile
|
adxl345: Add support for adxl345 accelerometer
|
2020-09-05 09:11:04 -04:00 |
|
adccmds.c
|
adccmds: Run gpio_adc_setup() before oid_alloc()
|
2019-01-13 11:03:30 -05:00 |
|
basecmd.c
|
stepper: Use a reusable interface to the "move queue"
|
2020-12-04 16:10:13 -05:00 |
|
basecmd.h
|
stepper: Use a reusable interface to the "move queue"
|
2020-12-04 16:10:13 -05:00 |
|
buttons.c
|
buttons: initialize mcu buttons based on inverted state
|
2019-07-05 20:01:07 -04:00 |
|
byteorder.h
|
byteorder: Add a header file defining common byteswap functions
|
2018-05-21 09:44:40 -04:00 |
|
command.c
|
command: Fix handling of buffer passing in args[] on 64bit mcu
|
2020-10-30 14:04:12 -04:00 |
|
command.h
|
command: Add command_decode_ptr() helper
|
2020-10-30 14:04:08 -04:00 |
|
compiler.h
|
…
|
|
|
ctr.h
|
ctr: Encode negative integers in normal hex notation
|
2019-08-22 13:06:44 -04:00 |
|
debugcmds.c
|
command: Add command_decode_ptr() helper
|
2020-10-30 14:04:08 -04:00 |
|
endstop.c
|
endstop: Rename mcu end_stop commands to endstop
|
2019-07-12 08:10:53 -04:00 |
|
gpiocmds.c
|
gpiocmds: Merge digital output and soft pwm code
|
2020-12-10 12:06:26 -05:00 |
|
i2ccmds.c
|
command: Add command_decode_ptr() helper
|
2020-10-30 14:04:08 -04:00 |
|
initial_pins.c
|
initial_pins: Add ability to configure output pins at mcu startup
|
2019-03-17 20:56:25 -04:00 |
|
initial_pins.h
|
initial_pins: Add ability to configure output pins at mcu startup
|
2019-03-17 20:56:25 -04:00 |
|
lcd_hd44780.c
|
command: Add command_decode_ptr() helper
|
2020-10-30 14:04:08 -04:00 |
|
lcd_st7920.c
|
command: Add command_decode_ptr() helper
|
2020-10-30 14:04:08 -04:00 |
|
neopixel.c
|
neopixel: Fix neopixel_result message so that it contains an oid
|
2020-11-05 11:40:34 -05:00 |
|
pwmcmds.c
|
pwmcmds: Use move queue for hard PWM
|
2020-12-04 16:10:13 -05:00 |
|
sched.c
|
sched: Force sched_try_shutdown to be inlined
|
2018-10-13 11:47:00 -04:00 |
|
sched.h
|
pru: Support config_reset command to manually reset mcu
|
2017-09-03 23:16:38 -04:00 |
|
sensor_adxl345.c
|
sensor_adxl345: Remove unused stop_time parameter
|
2020-09-05 09:18:59 -04:00 |
|
spi_software.c
|
spi_software: Remove unused include file
|
2019-08-17 13:49:03 -04:00 |
|
spi_software.h
|
spi_software: Implementation of software spi
|
2019-02-13 11:52:20 -05:00 |
|
spicmds.c
|
command: Add command_decode_ptr() helper
|
2020-10-30 14:04:08 -04:00 |
|
spicmds.h
|
spicmds: Rework spi config commands
|
2019-08-06 18:56:53 -04:00 |
|
stepper.c
|
stepper: Use a reusable interface to the "move queue"
|
2020-12-04 16:10:13 -05:00 |
|
stepper.h
|
…
|
|
|
thermocouple.c
|
thermocouple: Define thermocouple types using enumerations
|
2019-03-17 19:38:18 -04:00 |
|
tmcuart.c
|
command: Add command_decode_ptr() helper
|
2020-10-30 14:04:08 -04:00 |
267a2f3a38