105 lines
1.9 KiB
INI
105 lines
1.9 KiB
INI
# This file contains pin mappings for the SUNLU S8 v1.01 (circa 2020), which
|
|
# is a modified RAMPS v1.3 board. To use this config, the firmware should be
|
|
# compiled for the AVR atmega2560. The following pins are available for
|
|
# expansion (e.g. ABL): ^PD2 (Z+ endstop), PG5, PE3, PH3, PB5
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PF0
|
|
dir_pin: !PF1
|
|
enable_pin: !PD7
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^!PE5
|
|
position_endstop: 0
|
|
position_max: 310
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: PF6
|
|
dir_pin: !PF7
|
|
enable_pin: !PF2
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^!PJ1
|
|
position_endstop: 0
|
|
position_max: 310
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: PL3
|
|
dir_pin: PL1
|
|
enable_pin: !PK0
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: ^!PD3
|
|
position_endstop: 0.5
|
|
position_max: 400
|
|
|
|
[extruder]
|
|
step_pin: PA4
|
|
dir_pin: !PA6
|
|
enable_pin: !PA2
|
|
microsteps: 16
|
|
rotation_distance: 33.280
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PB4
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PK5
|
|
control: pid
|
|
pid_kp: 25.588
|
|
pid_ki: 1.496
|
|
pid_kd: 109.388
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
[filament_switch_sensor runout]
|
|
pause_on_runout: True
|
|
switch_pin: ^PE4
|
|
|
|
[heater_bed]
|
|
heater_pin: PH5
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PK6
|
|
control: pid
|
|
pid_kp: 74.786
|
|
pid_ki: 0.766
|
|
pid_kd: 1825.718
|
|
min_temp: 0
|
|
max_temp: 110
|
|
|
|
[verify_heater heater_bed]
|
|
# The stock printer heats slowly due to a large bed and no external MOSFET.
|
|
# This should be reduced if an external MOSFET is added to increase max_temp
|
|
# and heating rate.
|
|
check_gain_time: 240
|
|
|
|
[fan]
|
|
pin: PH6
|
|
|
|
[heater_fan fan1]
|
|
pin: PH4
|
|
|
|
[mcu]
|
|
serial: /dev/ttyUSB0
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 10
|
|
max_z_accel: 100
|
|
|
|
[display]
|
|
lcd_type: st7920
|
|
cs_pin: PH1
|
|
sclk_pin: PA1
|
|
sid_pin: PH0
|
|
encoder_pins: ^PC4, ^PC6
|
|
click_pin: ^!PC2
|
|
|
|
[output_pin beeper]
|
|
pin: PC0
|