160 lines
3.8 KiB
INI
160 lines
3.8 KiB
INI
# This file contains common configurations and pin mappings for the Prusa Buddy
|
|
# board. The LCD is not currently supported by Klipper, so the touchscreen will
|
|
# permanently display the bootloader screen after the Klipper firmware is flashed;
|
|
# use Fluidd, Mainsail, or OctoPrint etc. to control the printer.
|
|
|
|
# To use this config, the firmware should be compiled for the STM32F407. When
|
|
# running "make menuconfig", enable "extra low-level configuration setup",
|
|
# select the "128KiB + 512 byte offset" bootloader, and USB communication.
|
|
# Connect the printer to your Raspberry Pi using the printer's micro-USB port.
|
|
# If you prefer to remove Prusa's stock bootloader entirely, select the
|
|
# "No bootloader" option.
|
|
|
|
# When flashing for the first time, you will need to break the "appendix"
|
|
# on the Buddy board, then put the device into DFU mode by moving the jumper
|
|
# on the 3-pin header (older boards) or shorting the 2-pin header (newer boards)
|
|
# and resetting, and finally use "make flash" to install Klipper. Once Klipper is
|
|
# installed, you no longer need the jumper - just use "make flash" which will
|
|
# automatically put the device into DFU mode.
|
|
|
|
# Note that if you were previously running Prusa firmware, you must fully
|
|
# power cycle the board after flashing. Otherwise, Klipper will be unable to
|
|
# communicate with the TMC2209s due to the abrupt change in the baud rate,
|
|
# and will show this error: "Unable to read tmc uart register IFCNT".
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PD1
|
|
dir_pin: PD0
|
|
enable_pin: !PD3
|
|
microsteps: 16
|
|
rotation_distance: 32
|
|
endstop_pin: tmc2209_stepper_x:virtual_endstop
|
|
position_endstop: 200
|
|
position_min: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
homing_retract_dist: 0
|
|
|
|
[stepper_y]
|
|
step_pin: PD13
|
|
dir_pin: PD12
|
|
enable_pin: !PD14
|
|
microsteps: 16
|
|
rotation_distance: 32
|
|
endstop_pin: tmc2209_stepper_y:virtual_endstop
|
|
position_endstop: 0
|
|
position_min: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
homing_retract_dist: 0
|
|
|
|
[stepper_z]
|
|
step_pin: PD4
|
|
dir_pin: !PD15
|
|
enable_pin: !PD2
|
|
microsteps: 16
|
|
rotation_distance: 4
|
|
endstop_pin: probe:z_virtual_endstop
|
|
position_min: 0
|
|
position_max: 200
|
|
|
|
[extruder]
|
|
step_pin: PD9
|
|
dir_pin: !PD8
|
|
enable_pin: !PD10
|
|
microsteps: 16
|
|
rotation_distance: 33.500
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PB1
|
|
sensor_type: ATC Semitec 104GT-2
|
|
sensor_pin: PC0
|
|
control: pid
|
|
pid_Kp: 7
|
|
pid_Ki: 0.5
|
|
pid_Kd: 45
|
|
min_temp: 10
|
|
max_temp: 305
|
|
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PD5
|
|
uart_address: 1
|
|
diag_pin: ^PE2
|
|
driver_SGTHRS: 130
|
|
run_current: 0.35
|
|
sense_resistor: 0.22
|
|
stealthchop_threshold: 999999
|
|
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PD5
|
|
uart_address: 3
|
|
diag_pin: ^PE1
|
|
driver_SGTHRS: 130
|
|
run_current: 0.35
|
|
sense_resistor: 0.22
|
|
stealthchop_threshold: 999999
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PD5
|
|
uart_address: 0
|
|
diag_pin: ^PE3
|
|
driver_SGTHRS: 100
|
|
run_current: 0.35
|
|
sense_resistor: 0.22
|
|
stealthchop_threshold: 999999
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: PD5
|
|
uart_address: 2
|
|
diag_pin: ^PA15
|
|
driver_SGTHRS: 100
|
|
run_current: 0.4
|
|
sense_resistor: 0.22
|
|
|
|
[heater_bed]
|
|
heater_pin: PB0
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PA4
|
|
control: pid
|
|
pid_Kp: 120
|
|
pid_Ki: 1.5
|
|
pid_Kd: 600
|
|
min_temp: 10
|
|
max_temp: 110
|
|
|
|
# Hotend fan.
|
|
[heater_fan hotend_fan]
|
|
pin: PE9
|
|
tachometer_pin: PE14
|
|
|
|
# Part cooling fan.
|
|
[fan]
|
|
pin: PE11
|
|
tachometer_pin: PE10
|
|
|
|
# The SuperPINDA has built-in temperature compensation and no thermistor output,
|
|
# so no compensation table is needed. The PINDA thermistor is otherwise on pin PA6.
|
|
[probe]
|
|
pin: PA8
|
|
x_offset: -29
|
|
y_offset: -3
|
|
z_offset: 0
|
|
speed: 6.0
|
|
|
|
[filament_switch_sensor filament_sensor]
|
|
switch_pin: ^PB4
|
|
pause_on_runout: True
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-Klipper_stm32f407xx_3100380013504E4E53353420-if00
|
|
restart_method: command
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 180
|
|
max_accel: 1250
|
|
max_z_velocity: 12
|
|
max_z_accel: 400
|