klipper/lib/hal-stm32f1/include
Grigori Goronzy 75d5737211 Add STM32F103 port
Add a fully functional STM32F1 port, currently mostly targeting STM32F103
microcontrollers. This requires an 8 MHz XTAL. The maximum possible step rate
is around 282K steps per second.

This uses stm32flash to burn the firmware. The bootloader needs to be started
by setting BOOT0 to 1 and resetting the MCU. There is no automatic bootloader,
unlike on Arduino.

Signed-off-by: Grigori Goronzy <greg@kinoho.net>
2018-04-09 18:08:29 -04:00
..
stm32f1xx_hal.h
stm32f1xx_hal_adc.h
stm32f1xx_hal_adc_ex.h
stm32f1xx_hal_can.h
stm32f1xx_hal_can_ex.h
stm32f1xx_hal_cec.h
stm32f1xx_hal_conf.h
stm32f1xx_hal_cortex.h
stm32f1xx_hal_crc.h
stm32f1xx_hal_dac.h
stm32f1xx_hal_dac_ex.h
stm32f1xx_hal_def.h
stm32f1xx_hal_dma.h
stm32f1xx_hal_dma_ex.h
stm32f1xx_hal_eth.h
stm32f1xx_hal_flash.h
stm32f1xx_hal_flash_ex.h
stm32f1xx_hal_gpio.h
stm32f1xx_hal_gpio_ex.h
stm32f1xx_hal_hcd.h
stm32f1xx_hal_i2c.h
stm32f1xx_hal_i2s.h
stm32f1xx_hal_irda.h
stm32f1xx_hal_iwdg.h
stm32f1xx_hal_mmc.h
stm32f1xx_hal_nand.h
stm32f1xx_hal_nor.h
stm32f1xx_hal_pccard.h
stm32f1xx_hal_pcd.h
stm32f1xx_hal_pcd_ex.h
stm32f1xx_hal_pwr.h
stm32f1xx_hal_rcc.h
stm32f1xx_hal_rcc_ex.h
stm32f1xx_hal_rtc.h
stm32f1xx_hal_rtc_ex.h
stm32f1xx_hal_sd.h
stm32f1xx_hal_smartcard.h
stm32f1xx_hal_spi.h
stm32f1xx_hal_sram.h
stm32f1xx_hal_tim.h
stm32f1xx_hal_tim_ex.h
stm32f1xx_hal_uart.h
stm32f1xx_hal_usart.h
stm32f1xx_hal_wwdg.h
stm32f1xx_ll_adc.h
stm32f1xx_ll_bus.h
stm32f1xx_ll_cortex.h
stm32f1xx_ll_crc.h
stm32f1xx_ll_dac.h
stm32f1xx_ll_dma.h
stm32f1xx_ll_exti.h
stm32f1xx_ll_fsmc.h
stm32f1xx_ll_gpio.h
stm32f1xx_ll_i2c.h
stm32f1xx_ll_iwdg.h
stm32f1xx_ll_pwr.h
stm32f1xx_ll_rcc.h
stm32f1xx_ll_rtc.h
stm32f1xx_ll_sdmmc.h
stm32f1xx_ll_spi.h
stm32f1xx_ll_system.h
stm32f1xx_ll_tim.h
stm32f1xx_ll_usart.h
stm32f1xx_ll_usb.h
stm32f1xx_ll_utils.h
stm32f1xx_ll_wwdg.h