93 lines
1.6 KiB
INI
93 lines
1.6 KiB
INI
# This file contains common pin mappings for Anet A8 Plus printer from 2019.
|
|
# To use this config, the firmware should be compiled for
|
|
# the AVR atmega1284p.
|
|
|
|
# Note that the "make flash" command does not work with Anet boards -
|
|
# the boards are typically flashed with this command:
|
|
# avrdude -p atmega1284p -c arduino -b 57600 -P /dev/ttyUSB0 -U out/klipper.elf.hex
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PD7
|
|
dir_pin: !PC5
|
|
enable_pin: !PD6
|
|
microsteps: 16
|
|
rotation_distance: 32
|
|
endstop_pin: ^!PC2
|
|
position_endstop: -30
|
|
position_max: 300
|
|
position_min: -30
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: PC6
|
|
dir_pin: !PC7
|
|
enable_pin: !PD6
|
|
microsteps: 16
|
|
rotation_distance: 32
|
|
endstop_pin: ^!PC3
|
|
position_endstop: -8
|
|
position_max: 300
|
|
position_min: -8
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: PB3
|
|
dir_pin: !PB2
|
|
enable_pin: !PA5
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: ^!PC4
|
|
position_endstop: 0.5
|
|
position_max: 350
|
|
position_min: 0.5
|
|
homing_speed: 20
|
|
|
|
[extruder]
|
|
step_pin: PB1
|
|
dir_pin: PB0
|
|
enable_pin: !PD6
|
|
microsteps: 16
|
|
rotation_distance: 33.600
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PD5
|
|
sensor_type: Generic 3950
|
|
sensor_pin: PA7
|
|
control: pid
|
|
pid_Kp: 2.151492
|
|
pid_Ki: 0.633897
|
|
pid_Kd: 230.042965
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
[heater_bed]
|
|
heater_pin: PD4
|
|
sensor_type: Generic 3950
|
|
sensor_pin: PA6
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 100
|
|
|
|
[fan]
|
|
pin: PB4
|
|
|
|
[mcu]
|
|
serial: /dev/ttyUSB0
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 1000
|
|
max_z_velocity: 20
|
|
max_z_accel: 100
|
|
|
|
[display]
|
|
lcd_type: st7920
|
|
cs_pin: PA4
|
|
sclk_pin: PA1
|
|
sid_pin: PA3
|
|
encoder_pins: ^PD2, ^PD3
|
|
click_pin: ^!PC0
|