189 lines
4.6 KiB
INI
189 lines
4.6 KiB
INI
# Klipper firmware config file for Anycubic 4Max Pro 2.0. To use this config,
|
||
# the firmware should be compiled for the AVR atmega2560.
|
||
|
||
# You can build and flash firmware with commands in klipper directory:
|
||
# $ make clean
|
||
# $ make menuconfig
|
||
# $ make
|
||
# $ make flash FLASH_DEVICE={your serial port}
|
||
|
||
# For more precision, don't forget calibrate PIDs individually for your printer.
|
||
|
||
# For Anycubic 4Max Pro (not 2.0) owners:
|
||
# Be careful when using this config! This config tested only on Anycubic
|
||
# 4Max Pro 2.0! At first, you should
|
||
# set homing_speed on 5, and run homing and click on the endstops with
|
||
# your fingers. It is necessary to make sure that all the motors are
|
||
# spinning in the right direction, all the temperature sensors show the
|
||
# correct values, and all the endstops are triggered correctly.
|
||
|
||
# See docs/Config_Reference.md for a description of parameters.
|
||
|
||
[stepper_x]
|
||
step_pin: PF0
|
||
dir_pin: PF1
|
||
enable_pin: !PD7
|
||
rotation_distance: 32
|
||
microsteps: 16
|
||
endstop_pin: ^!PE5
|
||
position_min: -8
|
||
position_endstop: -8
|
||
position_max: 270
|
||
homing_speed: 50.0
|
||
homing_retract_dist: 5.0
|
||
second_homing_speed: 5.0
|
||
|
||
[stepper_y]
|
||
step_pin: PF6
|
||
dir_pin: !PF7
|
||
enable_pin: !PF2
|
||
rotation_distance: 40
|
||
microsteps: 16
|
||
endstop_pin: ^!PD2
|
||
position_max: 215
|
||
position_min: -1
|
||
position_endstop: -1
|
||
homing_speed: 50.0
|
||
homing_retract_dist: 5.0
|
||
second_homing_speed: 5.0
|
||
|
||
[stepper_z]
|
||
step_pin: PL3
|
||
dir_pin: PL1
|
||
enable_pin: !PK0
|
||
rotation_distance: 4
|
||
microsteps: 16
|
||
endstop_pin: ^!PD3
|
||
position_endstop: 0.0
|
||
position_max: 195
|
||
homing_speed: 5.0
|
||
homing_retract_dist: 3.0
|
||
second_homing_speed: 0.8
|
||
homing_speed: 6.0
|
||
|
||
[extruder]
|
||
step_pin: PA4
|
||
dir_pin: !PA6
|
||
enable_pin: !PA2
|
||
microsteps: 16
|
||
rotation_distance: 7.488
|
||
nozzle_diameter: 0.400
|
||
filament_diameter: 1.750
|
||
instantaneous_corner_velocity: 1.5
|
||
max_extrude_only_distance: 500
|
||
heater_pin: PB4
|
||
sensor_type: ATC Semitec 104GT-2
|
||
sensor_pin: PK5
|
||
smooth_time: 2
|
||
control: pid
|
||
pid_kp: 29.735 # calibrate these PID values for your printer individually!
|
||
pid_ki: 1.304 # calibrate these PID values for your printer individually!
|
||
pid_kd: 169.491 # calibrate these PID values for your printer individually!
|
||
min_temp: 0
|
||
max_temp: 280
|
||
|
||
[heater_bed]
|
||
heater_pin: PH5
|
||
sensor_type: EPCOS 100K B57560G104F
|
||
sensor_pin: PK6
|
||
control: pid
|
||
pid_kp: 71.423 # calibrate these PID values for your printer individually!
|
||
pid_ki: 0.679 # calibrate these PID values for your printer individually!
|
||
pid_kd: 1877.522 # calibrate these PID values for your printer individually!
|
||
min_temp: 0
|
||
max_temp: 125
|
||
|
||
[fan]
|
||
pin: PH6
|
||
kick_start_time: 1.0
|
||
|
||
[heater_fan heatbreak_fan]
|
||
pin: PL5
|
||
kick_start_time: 1.0
|
||
max_power: 1.0
|
||
heater_temp: 40.0
|
||
heater: extruder
|
||
|
||
[controller_fan system_fan]
|
||
pin: PH4
|
||
hardware_pwm: True
|
||
kick_start_time: 1.0
|
||
max_power: 1.0
|
||
idle_timeout: 300
|
||
idle_speed: 0.5
|
||
shutdown_speed: 1.0
|
||
heater: heater_bed,extruder
|
||
|
||
[output_pin light]
|
||
value: 1
|
||
pin: PL4
|
||
|
||
[mcu]
|
||
serial: /dev/serial/by-id/usb-Silicon_Labs_CP2102_USB_to_UART_Bridge_Controller_0001-if00-port0
|
||
restart_method: arduino
|
||
|
||
[printer]
|
||
kinematics: cartesian
|
||
max_velocity: 150
|
||
max_accel: 3000
|
||
max_accel_to_decel: 1500
|
||
max_z_velocity: 7
|
||
max_z_accel: 50
|
||
square_corner_velocity: 5
|
||
|
||
[bed_screws]
|
||
screw1: 5, 5
|
||
screw2: 265, 210
|
||
screw3: 5, 210
|
||
screw4: 265, 5
|
||
|
||
[filament_switch_sensor filament_sensor]
|
||
switch_pin: ^!PC4
|
||
|
||
[output_pin buzz]
|
||
pin: PC6
|
||
pwm: True
|
||
|
||
[output_pin AUTO_POWEROFF]
|
||
pin: PD0
|
||
pwm: True
|
||
cycle_time: 0.02
|
||
value: 1
|
||
|
||
|
||
# This macro (M300) uses internal integrated beeper
|
||
# Just use it in your G-code for making sounds. Example: M300 S1000 P500
|
||
[gcode_macro M300]
|
||
gcode:
|
||
{% set S = params.S|default(800)|float %}
|
||
{% set P = params.P|default(100)|int %}
|
||
SET_PIN PIN=buzz VALUE=0.5 CYCLE_TIME={ 1.0 / S | float }
|
||
G4 P{P}
|
||
SET_PIN PIN=buzz VALUE=0
|
||
|
||
# This macro (M81) uses internal integrated PSU control-relay.
|
||
# Just use M81 in your end_gcode if you want to poweroff your printer after print.
|
||
# Note: as in original Marlin firmware, before powerdown, printer will be cool hotend
|
||
# until temperature will be below 45°С / 113°F.
|
||
|
||
[gcode_macro M81]
|
||
gcode:
|
||
{% set required_extruder_temp = params.T|default(45)|int %}
|
||
{% if printer.extruder.temperature > required_extruder_temp|default(45)|int %}
|
||
M300
|
||
M300
|
||
M300
|
||
M117 COOLING DOWN BEFORE POWER OFF
|
||
M109 S{required_extruder_temp}
|
||
SET_PIN PIN=AUTO_POWEROFF VALUE=0.5
|
||
G4 P60
|
||
SET_PIN PIN=AUTO_POWEROFF VALUE=1
|
||
{% else %}
|
||
M300
|
||
M117 POWER OFF SOON
|
||
G4 P10000
|
||
SET_PIN PIN=AUTO_POWEROFF VALUE=0.5
|
||
G4 P60
|
||
SET_PIN PIN=AUTO_POWEROFF VALUE=1
|
||
{% endif %}
|