596 lines
23 KiB
Python
596 lines
23 KiB
Python
# Support for i2c based temperature sensors
|
|
#
|
|
# Copyright (C) 2020 Eric Callahan <arksine.code@gmail.com>
|
|
#
|
|
# This file may be distributed under the terms of the GNU GPLv3 license.
|
|
import logging
|
|
from . import bus
|
|
|
|
REPORT_TIME = .8
|
|
BME280_CHIP_ADDR = 0x76
|
|
|
|
BME280_REGS = {
|
|
'RESET': 0xE0, 'CTRL_HUM': 0xF2,
|
|
'STATUS': 0xF3, 'CTRL_MEAS': 0xF4, 'CONFIG': 0xF5,
|
|
'PRESSURE_MSB': 0xF7, 'PRESSURE_LSB': 0xF8, 'PRESSURE_XLSB': 0xF9,
|
|
'TEMP_MSB': 0xFA, 'TEMP_LSB': 0xFB, 'TEMP_XLSB': 0xFC,
|
|
'HUM_MSB': 0xFD, 'HUM_LSB': 0xFE, 'CAL_1': 0x88, 'CAL_2': 0xE1
|
|
}
|
|
|
|
BME680_REGS = {
|
|
'RESET': 0xE0, 'CTRL_HUM': 0x72, 'CTRL_GAS_1': 0x71, 'CTRL_GAS_0': 0x70,
|
|
'GAS_WAIT_0': 0x64, 'RES_HEAT_0': 0x5A, 'IDAC_HEAT_0': 0x50,
|
|
'STATUS': 0x73, 'EAS_STATUS_0': 0x1D, 'CTRL_MEAS': 0x74, 'CONFIG': 0x75,
|
|
'GAS_R_LSB': 0x2B, 'GAS_R_MSB': 0x2A,
|
|
'PRESSURE_MSB': 0x1F, 'PRESSURE_LSB': 0x20, 'PRESSURE_XLSB': 0x21,
|
|
'TEMP_MSB': 0x22, 'TEMP_LSB': 0x23, 'TEMP_XLSB': 0x24,
|
|
'HUM_MSB': 0x25, 'HUM_LSB': 0x26, 'CAL_1': 0x88, 'CAL_2': 0xE1,
|
|
'RES_HEAT_VAL': 0x00, 'RES_HEAT_RANGE': 0x02, 'RANGE_SWITCHING_ERROR': 0x04
|
|
}
|
|
|
|
BME680_GAS_CONSTANTS = {
|
|
0: (1., 8000000.),
|
|
1: (1., 4000000.),
|
|
2: (1., 2000000.),
|
|
3: (1., 1000000.),
|
|
4: (1., 499500.4995),
|
|
5: (0.99, 248262.1648),
|
|
6: (1., 125000.),
|
|
7: (0.992, 63004.03226),
|
|
8: (1., 31281.28128),
|
|
9: (1., 15625.),
|
|
10: (0.998, 7812.5),
|
|
11: (0.995, 3906.25),
|
|
12: (1., 1953.125),
|
|
13: (0.99, 976.5625),
|
|
14: (1., 488.28125),
|
|
15: (1., 244.140625)
|
|
}
|
|
|
|
BMP180_REGS = {
|
|
'RESET': 0xE0,
|
|
'CAL_1': 0xAA,
|
|
'CTRL_MEAS': 0xF4,
|
|
'REG_MSB': 0xF6,
|
|
'REG_LSB': 0xF7,
|
|
'CRV_TEMP': 0x2E,
|
|
'CRV_PRES': 0x34
|
|
}
|
|
|
|
STATUS_MEASURING = 1 << 3
|
|
STATUS_IM_UPDATE = 1
|
|
MODE = 1
|
|
RUN_GAS = 1 << 4
|
|
NB_CONV_0 = 0
|
|
EAS_NEW_DATA = 1 << 7
|
|
GAS_DONE = 1 << 6
|
|
MEASURE_DONE = 1 << 5
|
|
RESET_CHIP_VALUE = 0xB6
|
|
|
|
BME_CHIPS = {
|
|
0x58: 'BMP280', 0x60: 'BME280', 0x61: 'BME680', 0x55: 'BMP180'
|
|
}
|
|
BME_CHIP_ID_REG = 0xD0
|
|
|
|
|
|
def get_twos_complement(val, bit_size):
|
|
if val & (1 << (bit_size - 1)):
|
|
val -= (1 << bit_size)
|
|
return val
|
|
|
|
|
|
def get_unsigned_short(bits):
|
|
return bits[1] << 8 | bits[0]
|
|
|
|
|
|
def get_signed_short(bits):
|
|
val = get_unsigned_short(bits)
|
|
return get_twos_complement(val, 16)
|
|
|
|
|
|
def get_signed_byte(bits):
|
|
return get_twos_complement(bits, 8)
|
|
|
|
|
|
def get_unsigned_short_msb(bits):
|
|
return bits[0] << 8 | bits[1]
|
|
|
|
|
|
def get_signed_short_msb(bits):
|
|
val = get_unsigned_short_msb(bits)
|
|
return get_twos_complement(val, 16)
|
|
|
|
class BME280:
|
|
def __init__(self, config):
|
|
self.printer = config.get_printer()
|
|
self.name = config.get_name().split()[-1]
|
|
self.reactor = self.printer.get_reactor()
|
|
self.i2c = bus.MCU_I2C_from_config(
|
|
config, default_addr=BME280_CHIP_ADDR, default_speed=100000)
|
|
self.mcu = self.i2c.get_mcu()
|
|
self.iir_filter = config.getint('bme280_iir_filter', 1)
|
|
self.os_temp = config.getint('bme280_oversample_temp', 2)
|
|
self.os_hum = config.getint('bme280_oversample_hum', 2)
|
|
self.os_pres = config.getint('bme280_oversample_pressure', 2)
|
|
self.gas_heat_temp = config.getint('bme280_gas_target_temp', 320)
|
|
self.gas_heat_duration = config.getint('bme280_gas_heat_duration', 150)
|
|
logging.info("BMxx80: Oversampling: Temp %dx Humid %dx Pressure %dx" % (
|
|
pow(2, self.os_temp - 1), pow(2, self.os_hum - 1),
|
|
pow(2, self.os_pres - 1)))
|
|
logging.info("BMxx80: IIR: %dx" % (pow(2, self.iir_filter) - 1))
|
|
|
|
self.temp = self.pressure = self.humidity = self.gas = self.t_fine = 0.
|
|
self.min_temp = self.max_temp = self.range_switching_error = 0.
|
|
self.max_sample_time = None
|
|
self.dig = self.sample_timer = None
|
|
self.chip_type = 'BMP280'
|
|
self.chip_registers = BME280_REGS
|
|
self.printer.add_object("bme280 " + self.name, self)
|
|
if self.printer.get_start_args().get('debugoutput') is not None:
|
|
return
|
|
self.printer.register_event_handler("klippy:connect",
|
|
self.handle_connect)
|
|
|
|
def handle_connect(self):
|
|
self._init_bmxx80()
|
|
self.reactor.update_timer(self.sample_timer, self.reactor.NOW)
|
|
|
|
def setup_minmax(self, min_temp, max_temp):
|
|
self.min_temp = min_temp
|
|
self.max_temp = max_temp
|
|
|
|
def setup_callback(self, cb):
|
|
self._callback = cb
|
|
|
|
def get_report_time_delta(self):
|
|
return REPORT_TIME
|
|
|
|
def _init_bmxx80(self):
|
|
def read_calibration_data_bmp280(calib_data_1):
|
|
dig = {}
|
|
dig['T1'] = get_unsigned_short(calib_data_1[0:2])
|
|
dig['T2'] = get_signed_short(calib_data_1[2:4])
|
|
dig['T3'] = get_signed_short(calib_data_1[4:6])
|
|
|
|
dig['P1'] = get_unsigned_short(calib_data_1[6:8])
|
|
dig['P2'] = get_signed_short(calib_data_1[8:10])
|
|
dig['P3'] = get_signed_short(calib_data_1[10:12])
|
|
dig['P4'] = get_signed_short(calib_data_1[12:14])
|
|
dig['P5'] = get_signed_short(calib_data_1[14:16])
|
|
dig['P6'] = get_signed_short(calib_data_1[16:18])
|
|
dig['P7'] = get_signed_short(calib_data_1[18:20])
|
|
dig['P8'] = get_signed_short(calib_data_1[20:22])
|
|
dig['P9'] = get_signed_short(calib_data_1[22:24])
|
|
return dig
|
|
|
|
def read_calibration_data_bme280(calib_data_1, calib_data_2):
|
|
dig = read_calibration_data_bmp280(calib_data_1)
|
|
dig['H1'] = calib_data_1[25] & 0xFF
|
|
dig['H2'] = get_signed_short(calib_data_2[0:2])
|
|
dig['H3'] = calib_data_2[2] & 0xFF
|
|
dig['H4'] = get_twos_complement(
|
|
(calib_data_2[3] << 4) | (calib_data_2[4] & 0x0F), 12)
|
|
dig['H5'] = get_twos_complement(
|
|
(calib_data_2[5] << 4) | ((calib_data_2[4] & 0xF0) >> 4), 12)
|
|
dig['H6'] = get_twos_complement(calib_data_2[6], 8)
|
|
return dig
|
|
|
|
def read_calibration_data_bme680(calib_data_1, calib_data_2):
|
|
dig = {}
|
|
dig['T1'] = get_unsigned_short(calib_data_2[8:10])
|
|
dig['T2'] = get_signed_short(calib_data_1[2:4])
|
|
dig['T3'] = get_signed_byte(calib_data_1[4])
|
|
|
|
dig['P1'] = get_unsigned_short(calib_data_1[6:8])
|
|
dig['P2'] = get_signed_short(calib_data_1[8:10])
|
|
dig['P3'] = calib_data_1[10]
|
|
dig['P4'] = get_signed_short(calib_data_1[12:14])
|
|
dig['P5'] = get_signed_short(calib_data_1[14:16])
|
|
dig['P6'] = get_signed_byte(calib_data_1[17])
|
|
dig['P7'] = get_signed_byte(calib_data_1[16])
|
|
dig['P8'] = get_signed_short(calib_data_1[20:22])
|
|
dig['P9'] = get_signed_short(calib_data_1[22:24])
|
|
dig['P10'] = calib_data_1[24]
|
|
|
|
dig['H1'] = get_twos_complement(
|
|
(calib_data_2[2] << 4) | (calib_data_2[1] & 0x0F), 12)
|
|
dig['H2'] = get_twos_complement(
|
|
(calib_data_2[0] << 4) | ((calib_data_2[1] & 0xF0) >> 4), 12)
|
|
dig['H3'] = get_signed_byte(calib_data_2[3])
|
|
dig['H4'] = get_signed_byte(calib_data_2[4])
|
|
dig['H5'] = get_signed_byte(calib_data_2[5])
|
|
dig['H6'] = calib_data_2[6]
|
|
dig['H7'] = get_signed_byte(calib_data_2[7])
|
|
|
|
dig['G1'] = get_signed_byte(calib_data_2[12])
|
|
dig['G2'] = get_signed_short(calib_data_2[10:12])
|
|
dig['G3'] = get_signed_byte(calib_data_2[13])
|
|
return dig
|
|
|
|
def read_calibration_data_bmp180(calib_data_1):
|
|
dig = {}
|
|
dig['AC1'] = get_signed_short_msb(calib_data_1[0:2])
|
|
dig['AC2'] = get_signed_short_msb(calib_data_1[2:4])
|
|
dig['AC3'] = get_signed_short_msb(calib_data_1[4:6])
|
|
dig['AC4'] = get_unsigned_short_msb(calib_data_1[6:8])
|
|
dig['AC5'] = get_unsigned_short_msb(calib_data_1[8:10])
|
|
dig['AC6'] = get_unsigned_short_msb(calib_data_1[10:12])
|
|
|
|
dig['B1'] = get_signed_short_msb(calib_data_1[12:14])
|
|
dig['B2'] = get_signed_short_msb(calib_data_1[14:16])
|
|
|
|
dig['MB'] = get_signed_short_msb(calib_data_1[16:18])
|
|
dig['MC'] = get_signed_short_msb(calib_data_1[18:20])
|
|
dig['MD'] = get_signed_short_msb(calib_data_1[20:22])
|
|
return dig
|
|
|
|
chip_id = self.read_id()
|
|
if chip_id not in BME_CHIPS.keys():
|
|
logging.info("bme280: Unknown Chip ID received %#x" % chip_id)
|
|
else:
|
|
self.chip_type = BME_CHIPS[chip_id]
|
|
logging.info("bme280: Found Chip %s at %#x" % (
|
|
self.chip_type, self.i2c.i2c_address))
|
|
|
|
# Reset chip
|
|
self.write_register('RESET', [RESET_CHIP_VALUE])
|
|
self.reactor.pause(self.reactor.monotonic() + .5)
|
|
|
|
# Make sure non-volatile memory has been copied to registers
|
|
if self.chip_type != 'BMP180':
|
|
# BMP180 has no status register available
|
|
status = self.read_register('STATUS', 1)[0]
|
|
while status & STATUS_IM_UPDATE:
|
|
self.reactor.pause(self.reactor.monotonic() + .01)
|
|
status = self.read_register('STATUS', 1)[0]
|
|
|
|
if self.chip_type == 'BME680':
|
|
self.max_sample_time = 0.5
|
|
self.sample_timer = self.reactor.register_timer(self._sample_bme680)
|
|
self.chip_registers = BME680_REGS
|
|
elif self.chip_type == 'BMP180':
|
|
self.max_sample_time = (1.25 + ((2.3 * self.os_pres) + .575)) / 1000
|
|
self.sample_timer = self.reactor.register_timer(self._sample_bmp180)
|
|
self.chip_registers = BMP180_REGS
|
|
else:
|
|
self.max_sample_time = \
|
|
(1.25 + (2.3 * self.os_temp) + ((2.3 * self.os_pres) + .575)
|
|
+ ((2.3 * self.os_hum) + .575)) / 1000
|
|
self.sample_timer = self.reactor.register_timer(self._sample_bme280)
|
|
self.chip_registers = BME280_REGS
|
|
|
|
if self.chip_type in ('BME680', 'BME280'):
|
|
self.write_register('CONFIG', (self.iir_filter & 0x07) << 2)
|
|
|
|
# Read out and calculate the trimming parameters
|
|
if self.chip_type == 'BMP180':
|
|
cal_1 = self.read_register('CAL_1', 22)
|
|
else:
|
|
cal_1 = self.read_register('CAL_1', 26)
|
|
cal_2 = self.read_register('CAL_2', 16)
|
|
if self.chip_type == 'BME280':
|
|
self.dig = read_calibration_data_bme280(cal_1, cal_2)
|
|
elif self.chip_type == 'BMP280':
|
|
self.dig = read_calibration_data_bmp280(cal_1)
|
|
elif self.chip_type == 'BME680':
|
|
self.dig = read_calibration_data_bme680(cal_1, cal_2)
|
|
elif self.chip_type == 'BMP180':
|
|
self.dig = read_calibration_data_bmp180(cal_1)
|
|
|
|
def _sample_bme280(self, eventtime):
|
|
# Enter forced mode
|
|
if self.chip_type == 'BME280':
|
|
self.write_register('CTRL_HUM', self.os_hum)
|
|
meas = self.os_temp << 5 | self.os_pres << 2 | MODE
|
|
self.write_register('CTRL_MEAS', meas)
|
|
|
|
try:
|
|
# wait until results are ready
|
|
status = self.read_register('STATUS', 1)[0]
|
|
while status & STATUS_MEASURING:
|
|
self.reactor.pause(
|
|
self.reactor.monotonic() + self.max_sample_time)
|
|
status = self.read_register('STATUS', 1)[0]
|
|
|
|
if self.chip_type == 'BME280':
|
|
data = self.read_register('PRESSURE_MSB', 8)
|
|
elif self.chip_type == 'BMP280':
|
|
data = self.read_register('PRESSURE_MSB', 6)
|
|
else:
|
|
return self.reactor.NEVER
|
|
except Exception:
|
|
logging.exception("BME280: Error reading data")
|
|
self.temp = self.pressure = self.humidity = .0
|
|
return self.reactor.NEVER
|
|
|
|
temp_raw = (data[3] << 12) | (data[4] << 4) | (data[5] >> 4)
|
|
self.temp = self._compensate_temp(temp_raw)
|
|
pressure_raw = (data[0] << 12) | (data[1] << 4) | (data[2] >> 4)
|
|
self.pressure = self._compensate_pressure_bme280(pressure_raw) / 100.
|
|
if self.chip_type == 'BME280':
|
|
humid_raw = (data[6] << 8) | data[7]
|
|
self.humidity = self._compensate_humidity_bme280(humid_raw)
|
|
if self.temp < self.min_temp or self.temp > self.max_temp:
|
|
self.printer.invoke_shutdown(
|
|
"BME280 temperature %0.1f outside range of %0.1f:%.01f"
|
|
% (self.temp, self.min_temp, self.max_temp))
|
|
measured_time = self.reactor.monotonic()
|
|
self._callback(self.mcu.estimated_print_time(measured_time), self.temp)
|
|
return measured_time + REPORT_TIME
|
|
|
|
def _sample_bme680(self, eventtime):
|
|
self.write_register('CTRL_HUM', self.os_hum & 0x07)
|
|
meas = self.os_temp << 5 | self.os_pres << 2
|
|
self.write_register('CTRL_MEAS', [meas])
|
|
|
|
gas_wait_0 = self._calculate_gas_heater_duration(self.gas_heat_duration)
|
|
self.write_register('GAS_WAIT_0', [gas_wait_0])
|
|
res_heat_0 = self._calculate_gas_heater_resistance(self.gas_heat_temp)
|
|
self.write_register('RES_HEAT_0', [res_heat_0])
|
|
gas_config = RUN_GAS | NB_CONV_0
|
|
self.write_register('CTRL_GAS_1', [gas_config])
|
|
|
|
def data_ready(stat):
|
|
new_data = (stat & EAS_NEW_DATA)
|
|
gas_done = not (stat & GAS_DONE)
|
|
meas_done = not (stat & MEASURE_DONE)
|
|
return new_data and gas_done and meas_done
|
|
|
|
# Enter forced mode
|
|
meas = meas | MODE
|
|
self.write_register('CTRL_MEAS', meas)
|
|
try:
|
|
# wait until results are ready
|
|
status = self.read_register('EAS_STATUS_0', 1)[0]
|
|
while not data_ready(status):
|
|
self.reactor.pause(
|
|
self.reactor.monotonic() + self.max_sample_time)
|
|
status = self.read_register('EAS_STATUS_0', 1)[0]
|
|
|
|
data = self.read_register('PRESSURE_MSB', 8)
|
|
gas_data = self.read_register('GAS_R_MSB', 2)
|
|
except Exception:
|
|
logging.exception("BME680: Error reading data")
|
|
self.temp = self.pressure = self.humidity = self.gas = .0
|
|
return self.reactor.NEVER
|
|
|
|
temp_raw = (data[3] << 12) | (data[4] << 4) | (data[5] >> 4)
|
|
if temp_raw != 0x80000:
|
|
self.temp = self._compensate_temp(temp_raw)
|
|
pressure_raw = (data[0] << 12) | (data[1] << 4) | (data[2] >> 4)
|
|
if pressure_raw != 0x80000:
|
|
self.pressure = self._compensate_pressure_bme680(
|
|
pressure_raw) / 100.
|
|
humid_raw = (data[6] << 8) | data[7]
|
|
self.humidity = self._compensate_humidity_bme680(humid_raw)
|
|
|
|
gas_valid = ((gas_data[1] & 0x20) == 0x20)
|
|
if gas_valid:
|
|
gas_heater_stable = ((gas_data[1] & 0x10) == 0x10)
|
|
if not gas_heater_stable:
|
|
logging.warning("BME680: Gas heater didn't reach target")
|
|
gas_raw = (gas_data[0] << 2) | ((gas_data[1] & 0xC0) >> 6)
|
|
gas_range = (gas_data[1] & 0x0F)
|
|
self.gas = self._compensate_gas(gas_raw, gas_range)
|
|
|
|
if self.temp < self.min_temp or self.temp > self.max_temp:
|
|
self.printer.invoke_shutdown(
|
|
"BME680 temperature %0.1f outside range of %0.1f:%.01f"
|
|
% (self.temp, self.min_temp, self.max_temp))
|
|
measured_time = self.reactor.monotonic()
|
|
self._callback(self.mcu.estimated_print_time(measured_time), self.temp)
|
|
return measured_time + REPORT_TIME
|
|
|
|
def _sample_bmp180(self, eventtime):
|
|
meas = self.chip_registers['CRV_TEMP']
|
|
self.write_register('CTRL_MEAS', meas)
|
|
|
|
try:
|
|
self.reactor.pause(self.reactor.monotonic() + .01)
|
|
data = self.read_register('REG_MSB', 2)
|
|
temp_raw = (data[0] << 8) | data[1]
|
|
except Exception:
|
|
logging.exception("BMP180: Error reading temperature")
|
|
self.temp = self.pressure = .0
|
|
return self.reactor.NEVER
|
|
|
|
meas = self.chip_registers['CRV_PRES'] | (self.os_pres << 6)
|
|
self.write_register('CTRL_MEAS', meas)
|
|
|
|
try:
|
|
self.reactor.pause(self.reactor.monotonic() + .01)
|
|
data = self.read_register('REG_MSB', 3)
|
|
pressure_raw = \
|
|
((data[0] << 16)|(data[1] << 8)|data[2]) >> (8 - self.os_pres)
|
|
except Exception:
|
|
logging.exception("BMP180: Error reading pressure")
|
|
self.temp = self.pressure = .0
|
|
return self.reactor.NEVER
|
|
|
|
self.temp = self._compensate_temp_bmp180(temp_raw)
|
|
self.pressure = self._compensate_pressure_bmp180(pressure_raw) / 100.
|
|
if self.temp < self.min_temp or self.temp > self.max_temp:
|
|
self.printer.invoke_shutdown(
|
|
"BMP180 temperature %0.1f outside range of %0.1f:%.01f"
|
|
% (self.temp, self.min_temp, self.max_temp))
|
|
measured_time = self.reactor.monotonic()
|
|
self._callback(self.mcu.estimated_print_time(measured_time), self.temp)
|
|
return measured_time + REPORT_TIME
|
|
|
|
|
|
def _compensate_temp(self, raw_temp):
|
|
dig = self.dig
|
|
var1 = ((raw_temp / 16384. - (dig['T1'] / 1024.)) * dig['T2'])
|
|
var2 = (
|
|
((raw_temp / 131072.) - (dig['T1'] / 8192.)) *
|
|
((raw_temp / 131072.) - (dig['T1'] / 8192.)) * dig['T3'])
|
|
self.t_fine = var1 + var2
|
|
return self.t_fine / 5120.0
|
|
|
|
def _compensate_pressure_bme280(self, raw_pressure):
|
|
dig = self.dig
|
|
t_fine = self.t_fine
|
|
var1 = t_fine / 2. - 64000.
|
|
var2 = var1 * var1 * dig['P6'] / 32768.
|
|
var2 = var2 + var1 * dig['P5'] * 2.
|
|
var2 = var2 / 4. + (dig['P4'] * 65536.)
|
|
var1 = (dig['P3'] * var1 * var1 / 524288. + dig['P2'] * var1) / 524288.
|
|
var1 = (1. + var1 / 32768.) * dig['P1']
|
|
if var1 == 0:
|
|
return 0.
|
|
else:
|
|
pressure = 1048576.0 - raw_pressure
|
|
pressure = ((pressure - var2 / 4096.) * 6250.) / var1
|
|
var1 = dig['P9'] * pressure * pressure / 2147483648.
|
|
var2 = pressure * dig['P8'] / 32768.
|
|
return pressure + (var1 + var2 + dig['P7']) / 16.
|
|
|
|
def _compensate_pressure_bme680(self, raw_pressure):
|
|
dig = self.dig
|
|
t_fine = self.t_fine
|
|
var1 = t_fine / 2. - 64000.
|
|
var2 = var1 * var1 * dig['P6'] / 131072.
|
|
var2 = var2 + var1 * dig['P5'] * 2.
|
|
var2 = var2 / 4. + (dig['P4'] * 65536.)
|
|
var1 = (dig['P3'] * var1 * var1 / 16384. + dig['P2'] * var1) / 524288.
|
|
var1 = (1. + var1 / 32768.) * dig['P1']
|
|
if var1 == 0:
|
|
return 0.
|
|
else:
|
|
pressure = 1048576.0 - raw_pressure
|
|
pressure = ((pressure - var2 / 4096.) * 6250.) / var1
|
|
var1 = dig['P9'] * pressure * pressure / 2147483648.
|
|
var2 = pressure * dig['P8'] / 32768.
|
|
var3 = (pressure / 256.) * (pressure / 256.) * (pressure / 256.) * (
|
|
dig['P10'] / 131072.)
|
|
return pressure + (var1 + var2 + var3 + (dig['P7'] * 128.)) / 16.
|
|
|
|
def _compensate_humidity_bme280(self, raw_humidity):
|
|
dig = self.dig
|
|
t_fine = self.t_fine
|
|
humidity = t_fine - 76800.
|
|
h1 = (
|
|
raw_humidity - (
|
|
dig['H4'] * 64. + dig['H5'] / 16384. * humidity))
|
|
h2 = (dig['H2'] / 65536. * (1. + dig['H6'] / 67108864. * humidity *
|
|
(1. + dig['H3'] / 67108864. * humidity)))
|
|
humidity = h1 * h2
|
|
humidity = humidity * (1. - dig['H1'] * humidity / 524288.)
|
|
return min(100., max(0., humidity))
|
|
|
|
def _compensate_humidity_bme680(self, raw_humidity):
|
|
dig = self.dig
|
|
temp_comp = self.temp
|
|
|
|
var1 = raw_humidity - (
|
|
(dig['H1'] * 16.) + ((dig['H3'] / 2.) * temp_comp))
|
|
var2 = var1 * ((dig['H2'] / 262144.) *
|
|
(1. + ((dig['H4'] / 16384.) * temp_comp) +
|
|
((dig['H5'] / 1048576.) * temp_comp * temp_comp)))
|
|
var3 = dig['H6'] / 16384.
|
|
var4 = dig['H7'] / 2097152.
|
|
humidity = var2 + ((var3 + (var4 * temp_comp)) * var2 * var2)
|
|
return min(100., max(0., humidity))
|
|
|
|
def _compensate_gas(self, gas_raw, gas_range):
|
|
gas_switching_error = self.read_register('RANGE_SWITCHING_ERROR', 1)[0]
|
|
var1 = (1340. + 5. * gas_switching_error) * \
|
|
BME680_GAS_CONSTANTS[gas_range][0]
|
|
gas = var1 * BME680_GAS_CONSTANTS[gas_range][1] / (
|
|
gas_raw - 512. + var1)
|
|
return gas
|
|
|
|
def _calculate_gas_heater_resistance(self, target_temp):
|
|
amb_temp = self.temp
|
|
heater_data = self.read_register('RES_HEAT_VAL', 3)
|
|
res_heat_val = get_signed_byte(heater_data[0])
|
|
res_heat_range = (heater_data[2] & 0x30) >> 4
|
|
dig = self.dig
|
|
var1 = (dig['G1'] / 16.) + 49.
|
|
var2 = ((dig['G2'] / 32768.) * 0.0005) + 0.00235
|
|
var3 = dig['G3'] / 1024.
|
|
var4 = var1 * (1. + (var2 * target_temp))
|
|
var5 = var4 + (var3 * amb_temp)
|
|
res_heat = (3.4 * ((var5 * (4. / (4. + res_heat_range))
|
|
* (1. / (1. + (res_heat_val * 0.002)))) - 25))
|
|
return int(res_heat)
|
|
|
|
def _calculate_gas_heater_duration(self, duration_ms):
|
|
if duration_ms >= 4032:
|
|
duration_reg = 0xff
|
|
else:
|
|
factor = 0
|
|
while duration_ms > 0x3F:
|
|
duration_ms //= 4
|
|
factor += 1
|
|
duration_reg = duration_ms + (factor * 64)
|
|
|
|
return duration_reg
|
|
|
|
def _compensate_temp_bmp180(self, raw_temp):
|
|
dig = self.dig
|
|
x1 = (raw_temp - dig['AC6']) * dig['AC5'] / 32768.
|
|
x2 = dig['MC'] * 2048 / (x1 + dig['MD'])
|
|
b5 = x1 + x2
|
|
self.t_fine = b5
|
|
return (b5 + 8)/16./10.
|
|
|
|
def _compensate_pressure_bmp180(self, raw_pressure):
|
|
dig = self.dig
|
|
b5 = self.t_fine
|
|
b6 = b5 - 4000
|
|
x1 = (dig['B2'] * (b6 * b6 / 4096)) / 2048
|
|
x2 = dig['AC2'] * b6 / 2048
|
|
x3 = x1 + x2
|
|
b3 = ((int(dig['AC1'] * 4 + x3) << self.os_pres) + 2) / 4
|
|
x1 = dig['AC3'] * b6 / 8192
|
|
x2 = (dig['B1'] * (b6 * b6 / 4096)) / 65536
|
|
x3 = ((x1 + x2) + 2) / 4
|
|
b4 = dig['AC4'] * (x3 + 32768) / 32768
|
|
b7 = (raw_pressure - b3) * (50000 >> self.os_pres)
|
|
if (b7 < 0x80000000):
|
|
p = (b7 * 2) / b4
|
|
else:
|
|
p = (b7 / b4) * 2
|
|
x1 = (p / 256) * (p / 256)
|
|
x1 = (x1 * 3038) / 65536
|
|
x2 = (-7357 * p) / 65536
|
|
p = p + (x1 + x2 + 3791) / 16.
|
|
return p
|
|
|
|
def read_id(self):
|
|
# read chip id register
|
|
regs = [BME_CHIP_ID_REG]
|
|
params = self.i2c.i2c_read(regs, 1)
|
|
return bytearray(params['response'])[0]
|
|
|
|
def read_register(self, reg_name, read_len):
|
|
# read a single register
|
|
regs = [self.chip_registers[reg_name]]
|
|
params = self.i2c.i2c_read(regs, read_len)
|
|
return bytearray(params['response'])
|
|
|
|
def write_register(self, reg_name, data):
|
|
if type(data) is not list:
|
|
data = [data]
|
|
reg = self.chip_registers[reg_name]
|
|
data.insert(0, reg)
|
|
self.i2c.i2c_write(data)
|
|
|
|
def get_status(self, eventtime):
|
|
data = {
|
|
'temperature': round(self.temp, 2),
|
|
'pressure': self.pressure
|
|
}
|
|
if self.chip_type in ('BME280', 'BME680'):
|
|
data['humidity'] = self.humidity
|
|
if self.chip_type == 'BME680':
|
|
data['gas'] = self.gas
|
|
return data
|
|
|
|
|
|
def load_config(config):
|
|
# Register sensor
|
|
pheaters = config.get_printer().load_object(config, "heaters")
|
|
pheaters.add_sensor_factory("BME280", BME280)
|