138 lines
3.5 KiB
INI
138 lines
3.5 KiB
INI
# This file contains an example configuration for the Replicape rev B3
|
|
# board. To use this config, one must compile and install the
|
|
# micro-controller code for the "Beaglebone PRU", and then compile and
|
|
# install the micro-controller code a second time for a "Linux
|
|
# process".
|
|
|
|
# NOTE: Klipper does not alter the input/output state of the
|
|
# Beaglebone pins and it does not control their pull-up resistors.
|
|
# Typically the correct settings are automatically applied when the
|
|
# Beaglebone detects the Replicape board, but if changes are needed
|
|
# they must be specified in a "device tree overlay" or via the
|
|
# config-pin program.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[mcu]
|
|
serial: /dev/rpmsg_pru30
|
|
|
|
[mcu host]
|
|
serial: /tmp/klipper_host_mcu
|
|
|
|
[replicape]
|
|
revision: B3
|
|
host_mcu: host
|
|
stepper_x_microstep_mode: spread16
|
|
stepper_x_current: 0.5
|
|
stepper_y_microstep_mode: spread16
|
|
stepper_y_current: 0.5
|
|
stepper_z_microstep_mode: spread16
|
|
stepper_z_current: 0.5
|
|
stepper_e_microstep_mode: 16
|
|
stepper_e_current: 0.5
|
|
|
|
[stepper_x]
|
|
step_pin: gpio0_27
|
|
dir_pin: gpio1_29
|
|
enable_pin: replicape:stepper_x_enable
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^gpio3_21
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: gpio1_12
|
|
dir_pin: gpio0_22
|
|
enable_pin: replicape:stepper_y_enable
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^gpio1_17
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: gpio0_23
|
|
dir_pin: gpio0_26
|
|
enable_pin: replicape:stepper_z_enable
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: ^gpio0_31
|
|
position_endstop: 0
|
|
position_max: 200
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 25
|
|
max_z_accel: 30
|
|
|
|
[extruder]
|
|
step_pin: gpio1_28
|
|
dir_pin: gpio1_15
|
|
enable_pin: replicape:stepper_e_enable
|
|
microsteps: 16
|
|
rotation_distance: 33.500
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: replicape:power_e
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: host:analog4
|
|
control: pid
|
|
pid_Kp: 22.2
|
|
pid_Ki: 1.08
|
|
pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
[heater_bed]
|
|
heater_pin: replicape:power_hotbed
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: host:analog6
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[fan]
|
|
pin: replicape:power_fan0
|
|
|
|
# The alternative servo pins channels on the endstops x2 and y2 can be used
|
|
# via the special relicape pins servo0 (gpio1_18) and servo1 (gpio1_19).
|
|
#[servo servo_x2]
|
|
#pin: replicape:servo0
|
|
# PWM output pin controlling the servo. This parameter must be
|
|
# provided.
|
|
#...
|
|
|
|
# Providing an example of a switch filament sensor using the Linux MCU for replicape, instead of the PRU which does not have enough memory:
|
|
#[filament_switch_sensor switch_sensor]
|
|
#switch_pin: HOST_X2_STOP
|
|
|
|
# providing board pin aliases for PRU firmware
|
|
[board_pins]
|
|
aliases:
|
|
# step/dir pins
|
|
X_DIR=gpio1_29, X_STEP=gpio0_27, Y_DIR=gpio0_22, Y_STEP=gpio1_12, Z_DIR=gpio0_26, Z_STEP=gpio0_23,
|
|
E_DIR=gpio1_15, E_STEP=gpio1_28, H_DIR=gpio1_14, H_STEP=gpio1_13,
|
|
# stepper fault pins
|
|
FAULT_X=gpio2_4, FAULT_Y=gpio2_5, FAULT_Z=gpio0_15, FAULT_E=gpio2_1, FAULT_H=gpio2_3,
|
|
# endstops
|
|
STOP_X1=gpio3_21, STOP_X2=gpio0_30, STOP_Y1=gpio1_17, STOP_Y2=gpio3_17, STOP_Z1=gpio0_31, STOP_Z2=gpio0_4,
|
|
# enable steppers (all on one pin)
|
|
STEPPER_ENABLE=gpio0_20,
|
|
# servos
|
|
SERVO_0=gpio1_18, SERVO_1=gpio1_19,
|
|
|
|
[board_pins host]
|
|
mcu: host
|
|
aliases:
|
|
# Host aliases for Linux MCU
|
|
HOST_X2_STOP=gpio30, HOST_Y2_STOP=gpio113, HOST_Z2_STOP=gpio4,
|
|
# Thermistors
|
|
THERM_E=analog4, THERM_H=analog5, THERM_BED=analog6,
|
|
# D1W pin
|
|
DALLAS=gpio2
|