102 lines
1.9 KiB
INI
102 lines
1.9 KiB
INI
# This file contains pin mappings for the SUNLU S8 v1.01 (circa 2020), which
|
|
# is a modified RAMPS v1.3 board. To use this config, the firmware should be
|
|
# compiled for the AVR atmega2560. The following pins are available for
|
|
# expansion (e.g. ABL): ^ar19 (Z+ endstop), ar4, ar5, ar6, ar11
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: ar54
|
|
dir_pin: !ar55
|
|
enable_pin: !ar38
|
|
step_distance: .0125
|
|
endstop_pin: ^!ar3
|
|
position_endstop: 0
|
|
position_max: 310
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: ar60
|
|
dir_pin: !ar61
|
|
enable_pin: !ar56
|
|
step_distance: .0125
|
|
endstop_pin: ^!ar14
|
|
position_endstop: 0
|
|
position_max: 310
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: ar46
|
|
dir_pin: ar48
|
|
enable_pin: !ar62
|
|
step_distance: .0025
|
|
endstop_pin: ^!ar18
|
|
position_endstop: 0.5
|
|
position_max: 400
|
|
|
|
[extruder]
|
|
step_pin: ar26
|
|
dir_pin: !ar28
|
|
enable_pin: !ar24
|
|
step_distance: .0104
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: ar10
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: analog13
|
|
control: pid
|
|
pid_kp: 25.588
|
|
pid_ki: 1.496
|
|
pid_kd: 109.388
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
[filament_switch_sensor runout]
|
|
pause_on_runout: True
|
|
switch_pin: ^ar2
|
|
|
|
[heater_bed]
|
|
heater_pin: ar8
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: analog14
|
|
control: pid
|
|
pid_kp: 74.786
|
|
pid_ki: 0.766
|
|
pid_kd: 1825.718
|
|
min_temp: 0
|
|
max_temp: 110
|
|
|
|
[verify_heater heater_bed]
|
|
# The stock printer heats slowly due to a large bed and no external MOSFET.
|
|
# This should be reduced if an external MOSFET is added to increase max_temp
|
|
# and heating rate.
|
|
check_gain_time: 240
|
|
|
|
[fan]
|
|
pin: ar9
|
|
|
|
[heater_fan fan1]
|
|
pin: ar7
|
|
|
|
[mcu]
|
|
serial: /dev/ttyUSB0
|
|
pin_map: arduino
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 10
|
|
max_z_accel: 100
|
|
|
|
[display]
|
|
lcd_type: st7920
|
|
cs_pin: ar16
|
|
sclk_pin: ar23
|
|
sid_pin: ar17
|
|
encoder_pins: ^ar33, ^ar31
|
|
click_pin: ^!ar35
|
|
|
|
[output_pin beeper]
|
|
pin: ar37
|