.. |
atsam
|
atsam: Update code to use armcm_boot mechanism
|
2019-08-22 09:58:58 -04:00 |
atsamd
|
atsamd: Update code to use armcm_boot mechanism
|
2019-08-22 09:58:58 -04:00 |
avr
|
avr: Simplify spi mode setting
|
2019-05-07 23:02:20 -04:00 |
generic
|
ctr: Add support for multiple integers in DECL_CTR_INT
|
2019-08-22 12:22:51 -04:00 |
linux
|
spicmds: Rework spi config commands
|
2019-08-06 18:56:53 -04:00 |
lpc176x
|
lpc176x: Update code to use armcm_boot mechanism
|
2019-08-22 09:58:58 -04:00 |
pru
|
pru: The TMR_CNT is cleared by writing all ones
|
2019-03-31 13:48:50 -04:00 |
simulator
|
simulator: Wrap code to 80 columns
|
2019-02-27 14:20:15 -05:00 |
stm32
|
stm32: Update code to use armcm_boot mechanism
|
2019-08-22 09:58:58 -04:00 |
stm32f0
|
stm32f0: Remove trailing tab from Makefile
|
2019-07-21 21:49:22 -04:00 |
Kconfig
|
stm32: Rename stm32f4/ directory to stm32/
|
2019-08-05 11:25:40 -04:00 |
Makefile
|
initial_pins: Only build when CONFIG_HAVE_GPIO is enabled
|
2019-07-24 01:09:45 -04:00 |
adccmds.c
|
adccmds: Run gpio_adc_setup() before oid_alloc()
|
2019-01-13 11:03:30 -05:00 |
basecmd.c
|
spicmds: Rework spi config commands
|
2019-08-06 18:56:53 -04:00 |
basecmd.h
|
spicmds: Rework spi config commands
|
2019-08-06 18:56:53 -04:00 |
buttons.c
|
buttons: initialize mcu buttons based on inverted state
|
2019-07-05 20:01:07 -04:00 |
byteorder.h
|
byteorder: Add a header file defining common byteswap functions
|
2018-05-21 09:44:40 -04:00 |
command.c
|
command: Wait to send ack until after processing commands
|
2018-05-28 10:43:40 -04:00 |
command.h
|
ctr: Add support for multiple integers in DECL_CTR_INT
|
2019-08-22 12:22:51 -04:00 |
compiler.h
|
compiler.h: Check if __aligned and __section macros are already defined
|
2016-06-13 23:18:59 -04:00 |
ctr.h
|
ctr: Add support for multiple integers in DECL_CTR_INT
|
2019-08-22 12:22:51 -04:00 |
debugcmds.c
|
debugcmds: Add support for reading/writing 32bit values
|
2019-02-07 11:50:14 -05:00 |
endstop.c
|
endstop: Rename mcu end_stop commands to endstop
|
2019-07-12 08:10:53 -04:00 |
gpiocmds.c
|
gpiocmds: Specify soft pwm duration in clock ticks
|
2019-05-26 11:09:32 -04:00 |
i2ccmds.c
|
bus: Change bus parameter in config_spi/config_i2c
|
2019-04-04 18:29:31 -04:00 |
initial_pins.c
|
initial_pins: Add ability to configure output pins at mcu startup
|
2019-03-17 20:56:25 -04:00 |
initial_pins.h
|
initial_pins: Add ability to configure output pins at mcu startup
|
2019-03-17 20:56:25 -04:00 |
lcd_hd44780.c
|
lcd_hd44780: Add micro-controller code for the HD44780 LCD chip
|
2018-03-06 11:30:34 -05:00 |
lcd_st7920.c
|
lcd_st7920: Add brief delay around gpio toggle calls on fast MCUs
|
2019-08-10 11:45:15 -04:00 |
neopixel.c
|
neopixel: Rework timing so that it works on AVR micro-controllers
|
2019-08-07 15:37:05 -04:00 |
pwmcmds.c
|
pwmcmds: allow 16-bit resolution
|
2019-04-05 19:02:48 -04:00 |
sched.c
|
sched: Force sched_try_shutdown to be inlined
|
2018-10-13 11:47:00 -04:00 |
sched.h
|
pru: Support config_reset command to manually reset mcu
|
2017-09-03 23:16:38 -04:00 |
spi_software.c
|
spi_software: Remove unused include file
|
2019-08-17 13:49:03 -04:00 |
spi_software.h
|
spi_software: Implementation of software spi
|
2019-02-13 11:52:20 -05:00 |
spicmds.c
|
spicmds: Rework spi config commands
|
2019-08-06 18:56:53 -04:00 |
spicmds.h
|
spicmds: Rework spi config commands
|
2019-08-06 18:56:53 -04:00 |
stepper.c
|
stepper: Don't update SF_LAST_DIR if SF_NEED_RESET
|
2019-07-12 07:54:24 -04:00 |
stepper.h
|
stepper: Introduce stepper_get_position command and remove from endstop.c
|
2017-03-09 14:54:52 -05:00 |
thermocouple.c
|
thermocouple: Define thermocouple types using enumerations
|
2019-03-17 19:38:18 -04:00 |
tmcuart.c
|
pins: Add support for pull down resistors
|
2019-02-27 11:13:21 -05:00 |