148 lines
2.6 KiB
INI
148 lines
2.6 KiB
INI
# This file contains common pin mappings for the Duet2 Maestro. To use
|
|
# this config, the firmware should be compiled for the sam4s8c.
|
|
|
|
# See the example.cfg file for a description of available parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PC20
|
|
dir_pin: PC18
|
|
enable_pin: !PA1
|
|
step_distance: .0125
|
|
endstop_pin: ^PA24
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[tmc2208 stepper_x]
|
|
uart_pin: PA9
|
|
tx_pin: PA10
|
|
select_pins: !PC14, !PC16, !PC17
|
|
sense_resistor: 0.075
|
|
microsteps: 16
|
|
run_current: 0.800
|
|
stealthchop_threshold: 250
|
|
|
|
[stepper_y]
|
|
step_pin: PC2
|
|
dir_pin: PA8
|
|
enable_pin: !PA1
|
|
step_distance: .0125
|
|
endstop_pin: ^PB6
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[tmc2208 stepper_y]
|
|
uart_pin: PA9
|
|
tx_pin: PA10
|
|
select_pins: PC14, !PC16, !PC17
|
|
sense_resistor: 0.075
|
|
microsteps: 16
|
|
run_current: 0.800
|
|
stealthchop_threshold: 250
|
|
|
|
[stepper_z]
|
|
step_pin: PC28
|
|
dir_pin: PB4
|
|
enable_pin: !PA1
|
|
step_distance: .0025
|
|
endstop_pin: ^PC10
|
|
position_endstop: 0.5
|
|
position_max: 200
|
|
|
|
[tmc2208 stepper_z]
|
|
uart_pin: PA9
|
|
tx_pin: PA10
|
|
select_pins: !PC14, PC16, !PC17
|
|
sense_resistor: 0.075
|
|
microsteps: 16
|
|
run_current: 0.800
|
|
stealthchop_threshold: 30
|
|
|
|
[extruder]
|
|
step_pin: PC4
|
|
dir_pin: PB7
|
|
enable_pin: !PA1
|
|
step_distance: .002
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PC1
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PB0
|
|
control: pid
|
|
pid_Kp: 22.2
|
|
pid_Ki: 1.08
|
|
pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
[tmc2208 extruder]
|
|
uart_pin: PA9
|
|
tx_pin: PA10
|
|
select_pins: PC14, PC16, !PC17
|
|
sense_resistor: 0.075
|
|
microsteps: 16
|
|
run_current: 0.800
|
|
stealthchop_threshold: 5
|
|
|
|
#[extruder1]
|
|
#step_pin: PC5
|
|
#dir_pin: PC6
|
|
#enable_pin: !PA1
|
|
#heater_pin: PA16
|
|
#sensor_pin: PC30
|
|
#...
|
|
#[tmc2208 extruder1]
|
|
#select_pins: !PC14, !PC16, PC17
|
|
#sense_resistor: 0.075
|
|
#...
|
|
|
|
# External steppers
|
|
# e2: step_pin=PC31 dir_pin=PA18 enable_pin=PC27 select_pins=PC14,!PC16,PC17
|
|
# e3: step_pin=PC21 dir_pin=PC24 enable_pin=PC25 select_pins=!PC14,PC16,PC17
|
|
# e0_stop: endstop_pin=PA25
|
|
# e1_stop: endstop_pin=PC7
|
|
# c_temp: sensor_pin=PB1
|
|
|
|
[heater_bed]
|
|
heater_pin: PC0
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PA20
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[fan]
|
|
pin: PC23 # FAN0
|
|
|
|
#[heater_fan nozzle_cooling_fan]
|
|
#pin: PC22 # FAN1
|
|
|
|
#[heater_fan board_cooling_fan]
|
|
#pin: PC29 # FAN2
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
[static_digital_output led]
|
|
pins: !PC26
|
|
|
|
# "RepRapDiscount 128x64 Full Graphic Smart Controller" type displays
|
|
#[display]
|
|
#lcd_type: st7920
|
|
#cs_pin: PC9
|
|
#sclk_pin: PA2
|
|
#sid_pin: PA6
|
|
#encoder_pins: ^PC3, ^PB5
|
|
#click_pin: ^!PA7
|
|
#
|
|
#[output_pin BEEPER_pin]
|
|
#pin: PA15
|