3diy
/
klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
klipper/klippy/extras
History
Kevin O'Connor 797367b9f5 klippy: Convert printer_state("ready") to an event handler 
Convert all users of the printer_state("ready") handler to register a
"klippy:ready" event handler instead.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 		2019-01-08 10:59:43 -05:00
..
display klippy: Convert printer_state("ready") to an event handler 2019-01-08 10:59:43 -05:00
__init__.py
…
ad5206.py ad5206: Use bus.py helper code for spi 2018-11-21 12:12:31 -05:00
adc_temperature.py adc_temperature: Minor whitespace changes 2018-07-26 10:51:48 -04:00
bed_mesh.py bed_mesh: Introduce fade_target option 2018-11-30 11:37:21 -05:00
bed_tilt.py bed_tilt: Do not automatically run G28 on BED_TILT_CALIBRATE 2018-10-22 11:26:01 -04:00
bltouch.py bltouch: Issue both a "reset" and a "pin_up" after a successful probe 2018-12-16 11:06:46 -05:00
bus.py i2ccmds: Pass the i2c address as a 7-bit number (0-127) 2019-01-07 20:00:44 -05:00
buttons.py mcu: Rename add_config_object() to register_config_callback() 2018-09-03 11:48:22 -04:00
delta_calibrate.py delta_calibrate: Do not automatically run G28 on DELTA_CALIBRATE 2018-10-22 11:26:01 -04:00
endstop_phase.py tmc2660: Add endstop phase detection functionality to TMC2660 extra (#816) 2018-10-24 16:01:12 -04:00
fan.py fan: Allow the fan shutdown_speed to be configured 2018-05-18 19:12:03 -04:00
force_move.py force_move: Provide defaults for SET_KINEMATIC_POSITION parameters 2018-08-02 08:58:18 -04:00
gcode_macro.py gcode_macro: Provide more information on a formatting error 2018-09-30 12:43:54 -04:00
heater_bed.py heater: take a gcode_id when setting up a heater (#1028) 2019-01-02 17:44:02 -05:00
heater_fan.py klippy: Convert printer_state("ready") to an event handler 2019-01-08 10:59:43 -05:00
homing_override.py gcode: Rename run_script() to run_script_from_command() 2018-06-30 14:08:02 -04:00
idle_timeout.py klippy: Convert printer_state("ready") to an event handler 2019-01-08 10:59:43 -05:00
mcp4451.py i2ccmds: Pass the i2c address as a 7-bit number (0-127) 2019-01-07 20:00:44 -05:00
mcp4728.py mcp4728: Add initial support for the mcp4728 i2c dac chip 2019-01-02 18:17:56 -05:00
multi_pin.py pins: Explicitly pass can_invert and can_pullup to lookup_pin() 2018-07-26 09:44:45 -04:00
output_pin.py output_pin: Fix SET_PIN max_val check 2018-06-05 09:12:31 -04:00
pid_calibrate.py pid_calibrate: Add some comments on the calibration methodology 2018-10-19 22:40:11 -04:00
probe.py bltouch: Add initial support for a bltouch "extras" module 2018-11-30 11:34:20 -05:00
quad_gantry_level.py probe: Support manual probing at runtime 2018-10-01 11:12:30 -04:00
query_endstops.py query_endstops: Move QUERY_ENDSTOP command to it own extras/ module 2018-07-16 10:06:30 -04:00
replicape.py replicape: Use bus.py helper code for spi 2018-11-21 12:12:31 -05:00
respond.py respond: An extra for sending messages to the printer host. (#1053) 2019-01-02 17:45:35 -05:00
servo.py klippy: Convert printer_state("ready") to an event handler 2019-01-08 10:59:43 -05:00
spi_temperature.py spi_temperature: Use bus.py helper code for spi 2018-11-21 12:12:31 -05:00
static_digital_output.py static_digital_output: Add static_digital_output section to extras/ 2018-03-17 13:06:51 -04:00
statistics.py klippy: Convert printer_state("ready") to an event handler 2019-01-08 10:59:43 -05:00
sx1509.py i2ccmds: Pass the i2c address as a 7-bit number (0-127) 2019-01-07 20:00:44 -05:00
temperature_fan.py temperature_fan: Fix issue 403 use max_speed 2018-06-19 11:51:07 -04:00
thermistor.py thermistor: Avoid divide by zero error if min_temp=-273.15 2019-01-04 12:47:37 -05:00
tmc2130.py tmc2130: Use bus.py helper code for spi 2018-11-21 12:12:31 -05:00
tmc2208.py tmc2208: error raise fixed for rx/tx mcu check 2018-12-27 11:44:41 -05:00
tmc2660.py tmc2660: error and whitespace fixes 2018-12-27 11:44:41 -05:00
verify_heater.py klippy: Convert printer_state("shutdown") to an event handler 2019-01-08 10:59:43 -05:00
virtual_sdcard.py klippy: Convert printer_state("shutdown") to an event handler 2019-01-08 10:59:43 -05:00
z_tilt.py z_tilt: unresolved reference fixed 2019-01-08 08:44:25 -05:00