149 lines
2.8 KiB
INI
149 lines
2.8 KiB
INI
# This file contains pin mappings for the MTW Create (circa 2015). To
|
|
# use this config, the firmware should be compiled for the AVR
|
|
# atmega2560.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PC0
|
|
dir_pin: !PL1
|
|
enable_pin: !PA7
|
|
step_distance: .01
|
|
endstop_pin: ^PB6
|
|
#endstop_pin: ^PA2
|
|
position_endstop: 0
|
|
position_max: 250
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: PC1
|
|
dir_pin: PL0
|
|
enable_pin: !PA6
|
|
step_distance: .01
|
|
endstop_pin: ^PB5
|
|
#endstop_pin: ^PA1
|
|
position_endstop: 0
|
|
position_max: 320
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: PC2
|
|
dir_pin: PL2
|
|
enable_pin: !PA5
|
|
step_distance: .00125
|
|
endstop_pin: probe:z_virtual_endstop
|
|
#endstop_pin: ^PC7
|
|
position_endstop: 0.5
|
|
position_max: 225
|
|
|
|
[extruder]
|
|
step_pin: PC3
|
|
dir_pin: PL6
|
|
enable_pin: !PA4
|
|
step_distance: .0102
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PH6
|
|
sensor_type: ATC Semitec 104GT-2
|
|
sensor_pin: PF0
|
|
control: pid
|
|
pid_Kp: 22.2
|
|
pid_Ki: 1.08
|
|
pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 275
|
|
|
|
#Uncomment below for dual extruder printers
|
|
#[extruder1]
|
|
#step_pin: PC4
|
|
#dir_pin: PL7
|
|
#enable_pin: !PA3
|
|
#heater_pin: PH4
|
|
#sensor_pin: PF1
|
|
#step_distance: .0102
|
|
#nozzle_diameter: 0.400
|
|
#filament_diameter: 1.750
|
|
#sensor_type: ATC Semitec 104GT-2
|
|
#sensor_pin: PF0
|
|
#control: pid
|
|
#pid_Kp: 22.2
|
|
#pid_Ki: 1.08
|
|
#pid_Kd: 114
|
|
#min_temp: 0
|
|
#max_temp: 275
|
|
|
|
[heater_bed]
|
|
heater_pin: PE5
|
|
sensor_type: NTC 100K beta 3950
|
|
sensor_pin: PF2
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[bltouch]
|
|
sensor_pin: PB4
|
|
control_pin: PL5
|
|
x_offset: -17
|
|
y_offset: 37
|
|
z_offset: 2.0
|
|
|
|
[safe_z_home]
|
|
home_xy_position: 125,150
|
|
z_hop: 10
|
|
z_hop_speed: 5
|
|
|
|
[bed_mesh]
|
|
mesh_min: 5,5
|
|
mesh_max: 225,225
|
|
|
|
[fan]
|
|
pin: PH5
|
|
|
|
[heater_fan nozzle_cooling_fan]
|
|
pin: PH3
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-UltiMachine__ultimachine.com__RAMBo_854333433343516051F1-if00
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
[ad5206 stepper_digipot]
|
|
enable_pin: PD7
|
|
scale: 2.08
|
|
# Channel 1 is E0, 2 is E1, 3 is unused, 4 is Z, 5 is X, 6 is Y
|
|
channel_1: 1.34
|
|
channel_2: 1.0
|
|
channel_4: 1.1
|
|
channel_5: 1.1
|
|
channel_6: 1.1
|
|
|
|
# Enable 16 micro-steps on steppers X, Y, Z, E0, E1
|
|
[static_digital_output stepper_config]
|
|
pins:
|
|
PG1, PG0,
|
|
PK7, PG2,
|
|
PK6, PK5,
|
|
PK3, PK4,
|
|
PK1, PK2
|
|
|
|
[static_digital_output yellow_led]
|
|
pins: !PB7
|
|
|
|
# Common EXP1 / EXP2 (display) pins
|
|
[board_pins]
|
|
aliases:
|
|
# Common EXP1/EXP2 headers found on RAMBo v1.4
|
|
EXP1_1=PE6, EXP1_3=PG3, EXP1_5=PJ2, EXP1_7=PJ7, EXP1_9=<GND>,
|
|
EXP1_2=PE2, EXP1_4=PG4, EXP1_6=PJ3, EXP1_8=PJ4, EXP1_10=<5V>,
|
|
# EXP2 header
|
|
EXP2_1=PB3, EXP2_3=PJ5, EXP2_5=PJ6, EXP2_7=PD4, EXP2_9=<GND>,
|
|
EXP2_2=PB1, EXP2_4=PB0, EXP2_6=PB2, EXP2_8=PE7, EXP2_10=PH2
|
|
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi"
|
|
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|