118 lines
2.5 KiB
INI
118 lines
2.5 KiB
INI
[stepper_x]
|
||
step_pin: PF0
|
||
dir_pin: PF1
|
||
enable_pin: !PD7
|
||
microsteps: 16
|
||
rotation_distance: 40
|
||
endstop_pin: ^PE5
|
||
position_endstop: 0
|
||
position_max: 200
|
||
homing_speed: 50
|
||
|
||
[stepper_y]
|
||
step_pin: PF6
|
||
dir_pin: !PF7
|
||
enable_pin: !PF2
|
||
microsteps: 16
|
||
rotation_distance: 40
|
||
endstop_pin: ^PJ1
|
||
position_endstop: 0
|
||
position_max: 200
|
||
homing_speed: 50
|
||
|
||
[stepper_z]
|
||
step_pin: PL3
|
||
dir_pin: PL1
|
||
enable_pin: !PK0
|
||
microsteps: 16
|
||
rotation_distance: 8
|
||
endstop_pin: ^PD3
|
||
position_endstop: 0.5
|
||
position_max: 200
|
||
|
||
[extruder]
|
||
step_pin: PA4
|
||
dir_pin: PA6
|
||
enable_pin: !PA2
|
||
microsteps: 16
|
||
rotation_distance: 33.5
|
||
nozzle_diameter: 0.500
|
||
filament_diameter: 3.500
|
||
heater_pin: PB4
|
||
sensor_type: EPCOS 100K B57560G104F
|
||
sensor_pin: PK5
|
||
control: pid
|
||
pid_Kp: 22.2
|
||
pid_Ki: 1.08
|
||
pid_Kd: 114
|
||
min_temp: 0
|
||
max_temp: 210
|
||
|
||
[heater_bed]
|
||
heater_pin: PH5
|
||
sensor_type: EPCOS 100K B57560G104F
|
||
sensor_pin: PK6
|
||
control: watermark
|
||
min_temp: 0
|
||
max_temp: 110
|
||
|
||
[mcu]
|
||
serial: /dev/ttyACM0
|
||
|
||
[printer]
|
||
kinematics: cartesian
|
||
max_velocity: 300
|
||
max_accel: 3000
|
||
max_z_velocity: 5
|
||
max_z_accel: 100
|
||
|
||
# Test config for exclude_object
|
||
[exclude_object]
|
||
|
||
[gcode_macro M486]
|
||
gcode:
|
||
# Parameters known to M486 are as follows:
|
||
# [C<flag>] Cancel the current object
|
||
# [P<index>] Cancel the object with the given index
|
||
# [S<index>] Set the index of the current object.
|
||
# If the object with the given index has been canceled, this will cause
|
||
# the firmware to skip to the next object. The value -1 is used to
|
||
# indicate something that isn’t an object and shouldn’t be skipped.
|
||
# [T<count>] Reset the state and set the number of objects
|
||
# [U<index>] Un-cancel the object with the given index. This command will be
|
||
# ignored if the object has already been skipped
|
||
|
||
{% if 'exclude_object' not in printer %}
|
||
{action_raise_error("[exclude_object] is not enabled")}
|
||
{% endif %}
|
||
|
||
{% if 'T' in params %}
|
||
EXCLUDE_OBJECT RESET=1
|
||
|
||
{% for i in range(params.T | int) %}
|
||
EXCLUDE_OBJECT_DEFINE NAME={i}
|
||
{% endfor %}
|
||
{% endif %}
|
||
|
||
{% if 'C' in params %}
|
||
EXCLUDE_OBJECT CURRENT=1
|
||
{% endif %}
|
||
|
||
{% if 'P' in params %}
|
||
EXCLUDE_OBJECT NAME={params.P}
|
||
{% endif %}
|
||
|
||
{% if 'S' in params %}
|
||
{% if params.S == '-1' %}
|
||
{% if printer.exclude_object.current_object %}
|
||
EXCLUDE_OBJECT_END NAME={printer.exclude_object.current_object}
|
||
{% endif %}
|
||
{% else %}
|
||
EXCLUDE_OBJECT_START NAME={params.S}
|
||
{% endif %}
|
||
{% endif %}
|
||
|
||
{% if 'U' in params %}
|
||
EXCLUDE_OBJECT RESET=1 NAME={params.U}
|
||
{% endif %}
|