3diy
/
klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
klipper/config/printer-lulzbot-taz6-dual-v...

398 lines
16 KiB
INI
Raw Blame History

#This file contains pin mappings for the Lulzbot TAZ 6 circa 2017 using RAMBo and Dual v3 toolhead.
#To use this config, the firmware should be compiled for the AVR atmega2560.
# See docs/Config_Reference.md for a description of parameters.
#-------------------------------------------------------------------------------------------------
#-------------------------------------------------------------------------------------------------
#-------------------------------------------------------------------------------------------------
# LULZBOT TAZ6 (RAMBo) with Dual v3 Extruder Master Config
#-------------------------------------------------------------------------------------------------
#-------------------------------------------------------------------------------------------------
#-------------------------------------------------------------------------------------------------
#Notes:
# - This config includes START and END gcode blocks that already factor in the Marlin X and Y
# offsets for the Dual v3 toolhead using the true 0.01mm/step (100step/mm) linear movement value
# instead of the 0.00995mm/step (100.5step/mm) value that is stock on the TAZ6 to compensate for
# material shrinkage. Material shrinkage compensation should be done in the slicer based on the
# material being used.
#
# - The START and END gcode macros use parameters that should be set using the supplied START and
# END gcode blocks. These blocks have gcode variables that have been tested with Cura
# Ultimaker Edition (UE) v4.3 and opareate based on how many extruders are active.
#
# - Pressure Advance feature has been disabled and should be tuned if enabled.
#
# - All PID values pulled from Lulzbot Marlin 1.1.9.34, however, the PID calibration procedure
# should be done to tune these values to your specific hardware.
#
#-------------------------------------------------------------------------------------------------
# LULZBOT TAZ6 Dual v3 Required Parameters
#-------------------------------------------------------------------------------------------------
[stepper_x]
step_pin: PC0
dir_pin: PL1
enable_pin: !PA7
microsteps: 16
rotation_distance: 32
endstop_pin: ^PB6
position_endstop: -20
position_min: -20
position_max: 295
homing_speed: 50
second_homing_speed: 5
[stepper_y]
step_pin: PC1
dir_pin: !PL0
enable_pin: !PA6
microsteps: 16
rotation_distance: 32
endstop_pin: ^PA1
position_endstop: 306
position_min: -17
position_max: 306
homing_speed: 50
second_homing_speed: 5
[stepper_z]
step_pin: PC2
dir_pin: PL2
enable_pin: !PA5
microsteps: 16
rotation_distance: 2
endstop_pin: ^!PB4
position_endstop: 5.0
position_min: -5.8
position_max: 270
homing_speed: 10
second_homing_speed: 1
[extruder]
# This is Extruder0 on the dual v3 (all -1 index in schematic)
# The Dual v3 uses the same temp sensor as the single extruder
# The Dual v3 uses 2x SOMEstruders with modified PID values
step_pin: PC4
dir_pin: !PL7
enable_pin: !PA3
microsteps: 16
rotation_distance: 4.211
nozzle_diameter: 0.500
filament_diameter: 2.850
heater_pin: PH4
sensor_type: ATC Semitec 104GT-2
sensor_pin: PF1
control: pid
pid_Kp: 47.45
pid_Ki: 4.83
pid_Kd: 116.63
min_temp: 0
max_temp: 300
min_extrude_temp: 120
[extruder1]
# This is Extruder1 on the dual v3 (all -0 index in schematic)
# The Dual v3 uses the same temp sensor as the single extruder
# The Dual v3 uses 2x SOMEstruders with modified PID values
step_pin: PC3
dir_pin: PL6
enable_pin: !PA4
microsteps: 16
rotation_distance: 4.211
nozzle_diameter: 0.500
filament_diameter: 2.850
heater_pin: PH6
sensor_type: ATC Semitec 104GT-2
sensor_pin: PF0
control: pid
pid_Kp: 47.45
pid_Ki: 4.83
pid_Kd: 116.63
min_temp: 0
max_temp: 300
min_extrude_temp: 120
[heater_bed]
#The Heater Bed uses Honeywell 100K 135-104LAG-J01 temp sensor and PID control
heater_pin: PE5
sensor_type: Honeywell 100K 135-104LAG-J01
sensor_pin: PF2
control: pid
pid_Kp: 162.0
pid_Ki: 17.0
pid_Kd: 378.0
min_temp: 0
max_temp: 130
[fan]
#On Dual v3 heat break fan is connected to PH3 (part cooling fan on single extruder)
pin: PH3
[heater_fan nozzle_cooling_fan]
#On Dual v3 part fans are connected to PH5 (heat break fan on single extruder)
pin: PH5
[mcu]
serial: /dev/ttyACM0
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 2
max_z_accel: 10
[ad5206 stepper_digipot]
enable_pin: PD7
scale: 2.08
# Channel 1 is E0, 2 is E1, 3 is unused, 4 is Z, 5 is X, 6 is Y
channel_1: 1.34
channel_2: 1.34
channel_4: 1.1
channel_5: 1.1
channel_6: 1.1
[static_digital_output stepper_config]
# Enable 16 micro-steps on steppers X, Y, Z, E0, E1
pins:
PG1, PG0,
PK7, PG2,
PK6, PK5,
PK3, PK4,
PK1, PK2
[static_digital_output yellow_led]
pins: !PB7
[display]
lcd_type: st7920
cs_pin: PG4
sclk_pin: PJ2
sid_pin: PG3
encoder_pins: ^PJ6,^PJ5
click_pin: ^!PE2
menu_timeout:5
[probe]
#Define the nozzle probe feature
pin: ^!PA0
#---> z_offset may vary from machine to machine. Stock is 1.377. <---
z_offset:1.350
speed: 1.0
samples: 2
samples_tolerance: 0.100
[bed_tilt]
#Enable bed tilt measurments using the probe we defined above
#Probe points using X0 Y0 offsets @ 0.01mm/step
points: -3,-6
282,-6
282,300
-3,300
speed: 75
horizontal_move_z: 5
[safe_z_home]
#Needed to lift the Z to clear homing switch on bed
# ---> WARNING! - Z_MAX limit switch not monitored in Klipper! <---
# ---> This could potentially crash the toolhead if already at the top of Z travel! <---
home_xy_position: -19,265
speed: 50.0
z_hop: 15.0
move_to_previous: False
[gcode_macro G29]
#Preform the ABL by running G29 in the START gcode script
gcode:
BED_TILT_CALIBRATE
#-------------------------------------------------------------------------------------------------
# Macros to Support TAZ6 START and END Blocks
#-------------------------------------------------------------------------------------------------
#Cura UE 4.3 (and perhaps older) has extruder enable controls that define the number of active
#extruders. These blocks use that information to control only the active extruders.
#NOTE: T0 is the default extruder, T1 is optional.
#START block for use with dual or single extrusion prints
[gcode_macro START_PRINT]
default_parameter_EXTRUDERS_ENABLED_COUNT: 1
default_parameter_MATERIAL_STANDBY_TEMPERATURE_0: 175
default_parameter_MATERIAL_STANDBY_TEMPERATURE_1: 175
default_parameter_MATERIAL_BED_TEMPERATURE_LAYER_0: 65
default_parameter_MATERIAL_PRINT_TEMPERATURE_LAYER_0_0: 210
default_parameter_MATERIAL_PRINT_TEMPERATURE_LAYER_0_1: 210
#configure the params below to tune the stage desired temperatures based on the standby temps
default_parameter_MATERIAL_SOFTEN_TEMP_OFFSET: 35
default_parameter_MATERIAL_WIPE_TEMP_OFFSET: 35
default_parameter_MATERIAL_PROBE_TEMP_OFFSET: 35
gcode:
;This profile is designed specifically for LulzBot TAZ6 3D Printer with the Yellowfin Dual running Klipper
M73 P0 ; clear GLCD progress bar
M107 ; disable fans
G90 ; absolute positioning
M104 S{MATERIAL_STANDBY_TEMPERATURE_0|int - MATERIAL_SOFTEN_TEMP_OFFSET|int} T0 ; soften filament
{% if EXTRUDERS_ENABLED_COUNT|int == 2 %}
M104 S{MATERIAL_STANDBY_TEMPERATURE_1|int - MATERIAL_SOFTEN_TEMP_OFFSET|int} T1 ; soften filament
{% endif %}
M140 S{MATERIAL_BED_TEMPERATURE_LAYER_0} ; get bed heating up
G28 X Y ; home X and Y
G1 X-17 F3000 ; clear X endstop
M117 Heating... ; LCD status message
M106 S64 ; Fan On lightly
M109 S{MATERIAL_STANDBY_TEMPERATURE_0|int - MATERIAL_SOFTEN_TEMP_OFFSET|int} T0 ; wait for temp
{% if EXTRUDERS_ENABLED_COUNT|int == 2 %}
M109 S{MATERIAL_STANDBY_TEMPERATURE_1|int - MATERIAL_SOFTEN_TEMP_OFFSET|int} T1 ; wait for temp
{% endif %}
M107 ; Fan Off
T0 ; return to first extruder
G28 Z ; home Z
T0 ; select this extruder first
M82 ; set extruder to absolute mode
G92 E0 ; set extruder to zero
G1 E-15 F100 ; suck up 15mm of filament
{% if EXTRUDERS_ENABLED_COUNT|int == 2 %}
T1 ; switch extruders
M82 ; set extruder to absolute mode
G92 E0 ; set extruder to zero
G1 E-15 F100 ; suck up 15mm of filament
{% endif %}
M104 S{MATERIAL_STANDBY_TEMPERATURE_0|int - MATERIAL_WIPE_TEMP_OFFSET|int} T0 ; set to wipe temp
{% if EXTRUDERS_ENABLED_COUNT|int == 2 %}
M104 S{MATERIAL_STANDBY_TEMPERATURE_1|int - MATERIAL_WIPE_TEMP_OFFSET|int} T1 ; set to wipe temp
{% endif %}
M106 ; Turn on fans to speed cooling
G1 X-18 Y107 F3000 ; move above wiper pad
M117 Cooling... ; LCD status message
M109 S{MATERIAL_STANDBY_TEMPERATURE_0|int - MATERIAL_WIPE_TEMP_OFFSET|int} T0 ; wait for T0 to reach temp
{% if EXTRUDERS_ENABLED_COUNT|int == 2 %}
M109 S{MATERIAL_STANDBY_TEMPERATURE_1|int - MATERIAL_WIPE_TEMP_OFFSET|int} T1 ; wait for T1 to reach temp
{% endif %}
M107 ; Turn off fan
M117 Wiping... ; LCD status message
T0 ; switch extruders
G1 Z1 ; push nozzle into wiper
G1 X -18 Y107 F1000 ; slow wipe
G1 X -18 Y102 F1000 ; slow wipe
G1 X -18 Y97 F1000 ; slow wipe
G1 X -17 Y102 F1000 ; slow wipe
G1 X -18 Y92 F1000 ; slow wipe
G1 X -17 Y107 F1000 ; slow wipe
G1 X -18 Y87 F2000 ; fast wipe
G1 X -17 Y77 F2000 ; fast wipe
G1 X -18 Y82 F2000 ; fast wipe
G1 X -17 Y72 F2000 ; fast wipe
G1 X -18 Y67 F2000 ; fast wipe
G1 X -17 Y62 F2000 ; fast wipe
G1 X -18 Y52 F2000 ; fast wipe
G1 X -17 Y57 F2000 ; fast wipe
G1 X -18 Y47 F2000 ; fast wipe
G1 X -17 Y52 F2000 ; fast wipe
G1 X -18 Y82 F2000 ; fast wipe
G1 X -17 Y42 Z2 F2000 ; fast wipe
G1 X -18 Y47 F2000 ; fast wipe
G1 X -17 Y37 F2000 ; fast wipe
G1 X -18 Y42 F2000 ; fast wipe
G1 X -17 Y37 Z1.5 F1000 ; slow wipe
G1 X -18 Y35 F1000 ; slow wipe
G1 X -17 Z5 ; raise extruder
M109 S{MATERIAL_STANDBY_TEMPERATURE_0|int - MATERIAL_PROBE_TEMP_OFFSET|int} ; heat to probe temp
M117 Leveling Bed... ; LCD status message
M204 S100 ; set accel for probing
G29 ; probe sequence (for auto-leveling)
G1 Z10 ; clear Z home switch
M204 S500 ; set accel back to normal
M117 Heating... ; LCD status message
M106 S64 ; Fan On lightly
M104 S{MATERIAL_PRINT_TEMPERATURE_LAYER_0_0} T0 ; set extruder temp
{% if EXTRUDERS_ENABLED_COUNT|int == 2 %}
M104 S{MATERIAL_PRINT_TEMPERATURE_LAYER_0_1} T1; set extruder temp
{% endif %}
G1 X100 Y-16 Z0.5 F3000 ; move to open space
M400 ; clear buffer
M109 S{MATERIAL_PRINT_TEMPERATURE_LAYER_0_0} T0 ; set extruder temp and wait
{% if EXTRUDERS_ENABLED_COUNT|int == 2 %}
M109 S{MATERIAL_PRINT_TEMPERATURE_LAYER_0_1} T1; set extruder temp and wait
{% endif %}
M107 ; Fan Off
M117 Purging... ; LCD status message
T0 ; select this extruder first
G92 E-15 ; set extruder negative amount to purge
G1 E0 F100 ; undo retraction
G92 E-15 ; set extruder negative amount to purge
G1 E0 F100 ; purge 15mm of filament
{% if EXTRUDERS_ENABLED_COUNT|int == 2 %}
T1 ; switch to second extruder
G92 E-15 ; set extruder negative amount to purge
G1 E0 F100 ; undo retraction
G92 E-15 ; set extruder negative amount to purge
G1 E0 F50 ; purge 15mm of filament
G92 E0 ; zero out T1
G1 E-15 F250 ; retract 15mm from T1 - extrude a 500mm skirt/brim to undo in initial layer
M400 ; clear buffer
M106 ; Max Fan Speed
M109 S{MATERIAL_STANDBY_TEMPERATURE_1} T1 ; wait for T1 to cool to prevent ooze
M107 ; Fan Off
{% endif %}
G1 Z0.5 ; clear bed (barely)
G1 X100 Y0 F5000 ; move above bed to shear off filament
T0 ; switch to first extruder
M190 S{MATERIAL_BED_TEMPERATURE_LAYER_0}; get bed temping up during first layer
G1 Z2 E0 F75
M400 ; clear buffer
M117 TAZ Printing... ; LCD status message
#END block for use with dual or single extrusion prints
[gcode_macro END_PRINT]
default_parameter_EXTRUDERS_ENABLED_COUNT: 1
default_parameter_MATERIAL_PART_REMOVAL_TEMPERATURE: 45
default_parameter_MATERIAL_KEEP_PART_REMOVAL_TEMPERATURE_T: 0
gcode:
M400
M104 S0 T0 ; T0 hotend off
{% if EXTRUDERS_ENABLED_COUNT|int == 2 %}
M104 S0 T1 ; T1 hotend off
{% endif %}
M107 ; fans off
G91 ; relative positioning
T0
G1 E-1 F300 ; retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z20 E-5 X-20 Y-20 F3000 ; move Z up a bit and retract filament even more
G1 E6 ; re-prime extruder 1
{% if EXTRUDERS_ENABLED_COUNT|int == 2 %}
T1
G1 E-5 F300 ; retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 E5 ; re-prime extruder 2
T0
{% endif %}
M117 Cooling ... ; progress indicator message
G90 ; absolute positioning
G1 Y0 F3000 ; move to cooling position
M190 S{MATERIAL_PART_REMOVAL_TEMPERATURE} ; set bed to cool off
G1 Y280 F3000 ; present finished print
M140 S{MATERIAL_KEEP_PART_REMOVAL_TEMPERATURE_T}; keep temperature or cool downs
M84 ; steppers off
G90 ; absolute positioning
M117 Print Complete ; progress indicator message
#---------------------------------------------------------------------------------------------------
# ULTIMAKER CURA START AND END SCRIPTS - Replace default START and STOP scripts with the below GCODE
#---------------------------------------------------------------------------------------------------
#---> Dual Extrusion Printer Profiles < ---
#; LulzBot Taz6 w/ Dual Extruder Klipper START gcode script (for Cura UE, tested on v4.3)
#; First, set START_PRINT Macro variables from Cura parameters
#SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=EXTRUDERS_ENABLED_COUNT VALUE={extruders_enabled_count}
#SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=MATERIAL_STANDBY_TEMPERATURE_0 VALUE={material_standby_temperature}
#SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=MATERIAL_STANDBY_TEMPERATURE_1 VALUE={material_standby_temperature, 1}
#SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=MATERIAL_BED_TEMPERATURE_LAYER_0 VALUE={material_bed_temperature_layer_0}
#SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=MATERIAL_PRINT_TEMPERATURE_LAYER_0_0 VALUE={material_print_temperature_layer_0}
#SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=MATERIAL_PRINT_TEMPERATURE_LAYER_0_1 VALUE={material_print_temperature_layer_0, 1}
#; Execute START_PRINT GCODE defined in Klipper config file
#START_PRINT
#; LulzBot Taz6 w/ Dual Extruder v3 Klipper END gcode script (for Cura UE, tested on v4.3)
#; First, set END_PRINT Macro variables from Cura parameters
#SET_GCODE_VARIABLE MACRO=END_PRINT VARIABLE=EXTRUDERS_ENABLED_COUNT VALUE={extruders_enabled_count}
#SET_GCODE_VARIABLE MACRO=END_PRINT VARIABLE=MATERIAL_PART_REMOVAL_TEMPERATURE VALUE=45
#SET_GCODE_VARIABLE MACRO=END_PRINT VARIABLE=MATERIAL_KEEP_PART_REMOVAL_TEMPERATURE_T VALUE=0
#; Execute END_PRINT GCODE defined in Klipper config file
#END_PRINT
Reference in New Issue View Git Blame Copy Permalink