182 lines
3.8 KiB
INI
182 lines
3.8 KiB
INI
# This file contains common pin mappings for the Eryone ER-20 board
|
|
# board. To use this config, the firmware should be compiled for the
|
|
# STM32F103 with a 16KiB HID Bootloader.
|
|
|
|
# Extra settings to support BL Touch, Filament Runout sensor and
|
|
# have setting for fixing GCode errors, these configus can be found on
|
|
# Eryone's Facebook Group under files.
|
|
# Facebook like to files: https://www.facebook.com/groups/247271792709370/files
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PB15
|
|
dir_pin: PB14
|
|
rotation_distance: 40
|
|
enable_pin: !PD10
|
|
microsteps: 16
|
|
endstop_pin: tmc2209_stepper_x:virtual_endstop
|
|
position_endstop: 0
|
|
position_max: 250
|
|
homing_speed: 40
|
|
homing_retract_dist: 0
|
|
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PC11
|
|
tx_pin: PC10
|
|
diag_pin: ^PD8
|
|
uart_address: 2
|
|
run_current: 0.6
|
|
stealthchop_threshold: 999999
|
|
driver_SGTHRS: 80
|
|
|
|
[stepper_y]
|
|
step_pin: PD14
|
|
dir_pin: !PD13
|
|
enable_pin: !PC6
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: tmc2209_stepper_y:virtual_endstop
|
|
position_min: -9
|
|
position_endstop: -9
|
|
position_max: 235
|
|
homing_speed: 50
|
|
homing_retract_dist: 0
|
|
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PC11
|
|
tx_pin: PC10
|
|
diag_pin: ^PD15
|
|
uart_address: 3
|
|
run_current: 0.7
|
|
stealthchop_threshold: 999999
|
|
driver_SGTHRS: 100
|
|
|
|
[stepper_z]
|
|
step_pin: PC8
|
|
dir_pin: !PC7
|
|
enable_pin: !PA8
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: probe:z_virtual_endstop
|
|
position_max: 250
|
|
position_min: -1
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PC11
|
|
tx_pin: PC10
|
|
diag_pin: ^PC9
|
|
uart_address: 1
|
|
run_current: 0.7
|
|
stealthchop_threshold: 999999
|
|
driver_SGTHRS: 0
|
|
|
|
[extruder]
|
|
step_pin: PE13
|
|
dir_pin: PE14
|
|
enable_pin: !PB13
|
|
microsteps: 16
|
|
# Stock extruder [200 steps/rot]*[16 steps]/[93 steps/mm]
|
|
rotation_distance: 34.4
|
|
nozzle_diameter: 0.4
|
|
filament_diameter: 1.75
|
|
max_extrude_only_distance: 150
|
|
heater_pin: PD11
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC1
|
|
control: pid
|
|
pid_kp: 26.11
|
|
pid_ki: 2.01
|
|
pid_kd: 85
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: PC11
|
|
tx_pin: PC10
|
|
uart_address: 0
|
|
run_current: 0.7
|
|
stealthchop_threshold: 999999
|
|
|
|
[heater_bed]
|
|
heater_pin: PD12
|
|
sensor_type: ATC Semitec 104GT-2
|
|
sensor_pin: PC2
|
|
control: pid
|
|
pid_kp: 100.12
|
|
pid_ki: 5
|
|
pid_kd: 305
|
|
min_temp: 0
|
|
max_temp: 100
|
|
|
|
[fan]
|
|
pin: PB5
|
|
|
|
[heater_fan heatbreak_cooling_fan]
|
|
pin: PB4
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
|
restart_method: command
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 1500
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
######################################################################
|
|
# Probing/Mesh Leveling settings for stock BL Touch.
|
|
# Please make sure you set the correct values for your offsets.
|
|
######################################################################
|
|
|
|
[bltouch]
|
|
sensor_pin: ^PA11
|
|
control_pin: PA12
|
|
pin_move_time: 0.700
|
|
x_offset: 34
|
|
y_offset: 0
|
|
z_offset: 2.6
|
|
pin_up_touch_mode_reports_triggered: False
|
|
|
|
[safe_z_home]
|
|
home_xy_position: 5, 5
|
|
z_hop: 5.0
|
|
z_hop_speed: 5.0
|
|
|
|
[bed_mesh]
|
|
speed: 80
|
|
mesh_min: 40, 20
|
|
mesh_max: 210, 205
|
|
probe_count: 5, 5
|
|
|
|
######################################################################
|
|
# "RepRapDiscount 128x64 Full Graphic Smart Controller" type display
|
|
######################################################################
|
|
|
|
[display]
|
|
lcd_type: st7920
|
|
cs_pin: EXP1_4
|
|
sclk_pin: EXP1_5
|
|
sid_pin: EXP1_3
|
|
encoder_pins: ^EXP2_3, ^EXP2_5
|
|
click_pin: ^!EXP1_2
|
|
#kill_pin: ^!EXP2_8
|
|
|
|
[output_pin beeper]
|
|
pin: EXP1_1
|
|
|
|
######################################################################
|
|
# EXP1 / EXP2 (display) pins
|
|
######################################################################
|
|
|
|
[board_pins]
|
|
aliases:
|
|
# EXP1 header
|
|
EXP1_1=PE12, EXP1_3=PE10, EXP1_5=PE8, EXP1_7=PB2,
|
|
EXP1_2=PE11, EXP1_4=PE9, EXP1_6=PE7, EXP1_8=PB1,
|
|
# EXP2 header
|
|
EXP2_3=PE4, EXP2_5=PE3
|
|
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi2"
|