85 lines
1.5 KiB
INI
85 lines
1.5 KiB
INI
# This file contains common pin mappings for Minitronics v1.0
|
|
# boards. To use this config, the firmware should be compiled for the
|
|
# AVR atmega1280.
|
|
|
|
# The "make flash" command does not work on the Minitronics v1.0
|
|
# because the board actually has an atmega1281 chip. Use the following
|
|
# command to flash the board:
|
|
# avrdude -carduino -patmega1281 -P/dev/ttyUSB0 -b57600 -D -Uout/klipper.elf.hex
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PF2
|
|
dir_pin: PF1
|
|
enable_pin: !PF3
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^!PE3
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: PA1
|
|
dir_pin: PA2
|
|
enable_pin: !PA0
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^!PE4
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: PA4
|
|
dir_pin: !PA5
|
|
enable_pin: !PA3
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: ^!PB4
|
|
position_endstop: 0.5
|
|
position_max: 200
|
|
|
|
[extruder]
|
|
step_pin: PA7
|
|
dir_pin: PA6
|
|
enable_pin: !PG2
|
|
microsteps: 16
|
|
rotation_distance: 33.500
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PB5
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PF7
|
|
control: pid
|
|
pid_Kp: 22.2
|
|
pid_Ki: 1.08
|
|
pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
[heater_bed]
|
|
heater_pin: PE5
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PF6
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[fan]
|
|
pin: PB7
|
|
|
|
[mcu]
|
|
serial: /dev/ttyUSB0
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
[static_digital_output yellow_led]
|
|
pins: PF0
|