123 lines
2.4 KiB
INI
123 lines
2.4 KiB
INI
# This file contains common pin mappings for RAMBo boards. To use this
|
|
# config, the firmware should be compiled for the AVR atmega2560.
|
|
|
|
# See the example.cfg file for a description of available parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PC0
|
|
dir_pin: PL1
|
|
enable_pin: !PA7
|
|
step_distance: .0125
|
|
endstop_pin: ^PB6
|
|
#endstop_pin: ^PA2
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: PC1
|
|
dir_pin: !PL0
|
|
enable_pin: !PA6
|
|
step_distance: .0125
|
|
endstop_pin: ^PB5
|
|
#endstop_pin: ^PA1
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: PC2
|
|
dir_pin: PL2
|
|
enable_pin: !PA5
|
|
step_distance: .0025
|
|
endstop_pin: ^PB4
|
|
#endstop_pin: ^PC7
|
|
position_endstop: 0.5
|
|
position_max: 200
|
|
|
|
[extruder]
|
|
step_pin: PC3
|
|
dir_pin: PL6
|
|
enable_pin: !PA4
|
|
step_distance: .002
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PH6
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PF0
|
|
control: pid
|
|
pid_Kp: 22.2
|
|
pid_Ki: 1.08
|
|
pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
#[extruder1]
|
|
#step_pin: PC4
|
|
#dir_pin: PL7
|
|
#enable_pin: !PA3
|
|
#heater_pin: PH4
|
|
#sensor_pin: PF1
|
|
#...
|
|
|
|
[heater_bed]
|
|
heater_pin: PE5
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PF2
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[fan]
|
|
pin: PH5
|
|
|
|
#[heater_fan nozzle_cooling_fan]
|
|
#pin: PH3
|
|
|
|
[mcu]
|
|
serial: /dev/ttyACM0
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
[ad5206 stepper_digipot]
|
|
enable_pin: PD7
|
|
# Scale the config so that the channel value can be specified in amps.
|
|
# (For Rambo v1.0d boards, use 1.56 instead.)
|
|
scale: 2.08
|
|
# Channel 1 is E0, 2 is E1, 3 is unused, 4 is Z, 5 is X, 6 is Y
|
|
channel_1: 1.34
|
|
channel_2: 1.0
|
|
channel_4: 1.1
|
|
channel_5: 1.1
|
|
channel_6: 1.1
|
|
|
|
# Enable 16 micro-steps on steppers X, Y, Z, E0, E1
|
|
[static_digital_output stepper_config]
|
|
pins:
|
|
PG1, PG0,
|
|
PK7, PG2,
|
|
PK6, PK5,
|
|
PK3, PK4,
|
|
PK1, PK2
|
|
|
|
[static_digital_output yellow_led]
|
|
pins: !PB7
|
|
|
|
# Common EXP1 / EXP2 (display) pins
|
|
[board_pins]
|
|
aliases:
|
|
# Common EXP1/EXP2 headers found on RAMBo v1.4
|
|
EXP1_1=PE6, EXP1_3=PG3, EXP1_5=PJ2, EXP1_7=PJ7, EXP1_9=<GND>,
|
|
EXP1_2=PE2, EXP1_4=PG4, EXP1_6=PJ3, EXP1_8=PJ4, EXP1_10=<5V>,
|
|
# EXP2 header
|
|
EXP2_1=PB3, EXP2_3=PJ5, EXP2_5=PJ6, EXP2_7=PD4, EXP2_9=<GND>,
|
|
EXP2_2=PB1, EXP2_4=PB0, EXP2_6=PB2, EXP2_8=PE7, EXP2_10=PH2
|
|
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi"
|
|
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|