| .. |
|
__init__.py
|
…
|
|
|
ad5206.py
|
spicmds: Rework SPI message transmission
|
2018-05-07 09:10:34 -04:00 |
|
adc_temperature.py
|
adc_temperature: Support defining custom sensors in the config file
|
2018-04-09 15:44:34 -04:00 |
|
bed_tilt.py
|
probe: Move code from bed_tilt and delta_calibrate into ProbePointsHelper
|
2018-05-20 11:41:07 -04:00 |
|
delta_calibrate.py
|
probe: Move code from bed_tilt and delta_calibrate into ProbePointsHelper
|
2018-05-20 11:41:07 -04:00 |
|
display.py
|
display: Round temperature and position to nearest whole number
|
2018-03-19 15:17:53 -04:00 |
|
fan.py
|
fan: Allow the fan shutdown_speed to be configured
|
2018-05-18 19:12:03 -04:00 |
|
heater_bed.py
|
heater: Add PrinterHeaters class that stores all sensors and heaters
|
2018-04-04 23:13:53 -04:00 |
|
heater_fan.py
|
fan: Allow the fan shutdown_speed to be configured
|
2018-05-18 19:12:03 -04:00 |
|
homing_override.py
|
klippy: Introduce load_config_prefix() for modules that take parameters
|
2018-02-03 12:53:11 -05:00 |
|
multi_pin.py
|
pins: Remove module level get_printer_pins() and setup_pin() functions
|
2018-04-04 12:26:39 -04:00 |
|
output_pin.py
|
gcode: Add minval/maxval/above/below options to get_X parsers
|
2018-04-20 22:24:36 -04:00 |
|
pid_calibrate.py
|
pid_calibrate: Make sure to unregister new control class on error
|
2018-04-06 11:39:24 -04:00 |
|
probe.py
|
probe: Verify horizontal_move_z not less than probe's z_offset
|
2018-05-20 11:41:28 -04:00 |
|
replicape.py
|
linux: Convert linux SPI code to use the generic spicmds.c code
|
2018-05-07 09:10:34 -04:00 |
|
servo.py
|
pins: Remove module level get_printer_pins() and setup_pin() functions
|
2018-04-04 12:26:39 -04:00 |
|
static_digital_output.py
|
static_digital_output: Add static_digital_output section to extras/
|
2018-03-17 13:06:51 -04:00 |
|
temperature_fan.py
|
fan: Allow the fan shutdown_speed to be configured
|
2018-05-18 19:12:03 -04:00 |
|
thermistor.py
|
thermistor: Add Honeywell 100K and MGB18 thermistor definitions
|
2018-04-30 16:08:17 -04:00 |
|
verify_heater.py
|
heater: Add PrinterHeaters class that stores all sensors and heaters
|
2018-04-04 23:13:53 -04:00 |
|
virtual_sdcard.py
|
virtual_sdcard: Add logging on start, stop, stats, and shutdown
|
2018-04-23 18:35:15 -04:00 |
6869e7d1ec