181 lines
3.3 KiB
INI
181 lines
3.3 KiB
INI
# This file contains pin mappings for a full Ratrig V-Minion kit
|
|
# with an Octopus Pro v1.1 board.
|
|
#
|
|
# This will not work with RatOS
|
|
#
|
|
# To use this config, during "make menuconfig" select the STM32F446
|
|
# with a "32KiB bootloader", USB (on PA11/PA12) communication, and
|
|
# a "12MHZ Crystal"
|
|
#
|
|
# Flash this firmware on the MCU by copying "out/klipper.bin" to an SD
|
|
# card and turning the printer on with the card inserted. The firmware
|
|
# filename must be named "firmware.bin"
|
|
#
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PF13
|
|
dir_pin: !PF12
|
|
enable_pin: !PF14
|
|
endstop_pin: ^PG6
|
|
rotation_distance: 40
|
|
microsteps: 64
|
|
position_max: 180
|
|
position_min: 0
|
|
homing_speed: 60
|
|
position_endstop: 0
|
|
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PC4
|
|
run_current: 0.8
|
|
interpolate: false
|
|
stealthchop_threshold: 0
|
|
|
|
[stepper_y]
|
|
step_pin: PG0
|
|
dir_pin: PG1
|
|
enable_pin: !PF15
|
|
endstop_pin: ^PG9
|
|
rotation_distance: 40
|
|
microsteps: 64
|
|
position_max: 180
|
|
position_min: 0
|
|
homing_speed: 60
|
|
position_endstop: 0
|
|
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PD11
|
|
run_current: 0.8
|
|
interpolate: false
|
|
stealthchop_threshold: 0
|
|
|
|
[stepper_z]
|
|
step_pin: PC13
|
|
dir_pin: !PF0
|
|
enable_pin: !PF1
|
|
endstop_pin: probe:z_virtual_endstop
|
|
rotation_distance: 4
|
|
position_min: -5
|
|
microsteps: 64
|
|
position_max: 180
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PE4
|
|
run_current: 0.8
|
|
interpolate: false
|
|
stealthchop_threshold: 0
|
|
|
|
[extruder]
|
|
rotation_distance: 5.57
|
|
full_steps_per_rotation: 200
|
|
filament_diameter: 1.750
|
|
step_pin: PF11
|
|
dir_pin: !PG3
|
|
enable_pin: !PG5
|
|
microsteps: 64
|
|
nozzle_diameter: 0.4
|
|
heater_pin: PA2
|
|
sensor_type: Generic 3950
|
|
sensor_pin: PF4
|
|
control: pid
|
|
pid_Kp: 22.2
|
|
pid_Ki: 1.08
|
|
pid_Kd: 114
|
|
|
|
min_temp: 0
|
|
max_temp: 290
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: PC6
|
|
run_current: 0.70
|
|
stealthchop_threshold: 0
|
|
interpolate: False
|
|
|
|
[probe]
|
|
pin: ^PB7
|
|
x_offset: -24.0
|
|
y_offset: -13.0
|
|
z_offset: 0.0
|
|
speed: 5
|
|
samples: 2
|
|
sample_retract_dist: 2
|
|
lift_speed: 5.0
|
|
samples_result: median
|
|
samples_tolerance: 0.02
|
|
samples_tolerance_retries: 5
|
|
|
|
[bed_mesh]
|
|
speed: 300
|
|
horizontal_move_z: 5
|
|
mesh_min: 15,15
|
|
mesh_max: 150,160
|
|
probe_count: 5,5
|
|
fade_start: 1.0
|
|
fade_end: 10.0
|
|
mesh_pps: 2,2
|
|
algorithm: bicubic
|
|
bicubic_tension: .2
|
|
|
|
[screws_tilt_adjust]
|
|
screw1: 80, 108
|
|
screw1_name: Left Screw
|
|
screw2: 155, 72
|
|
screw2_name: Front Right Screw
|
|
screw3: 155, 147
|
|
screw3_name: Rear Right Screw
|
|
horizontal_move_z: 10
|
|
speed: 300
|
|
screw_thread: CCW-M4
|
|
|
|
[safe_z_home]
|
|
home_xy_position: 90,90
|
|
z_hop: 5
|
|
speed: 300
|
|
|
|
[heater_bed]
|
|
heater_pin: PA1
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PF3
|
|
control: pid
|
|
pid_kp: 54.027
|
|
pid_ki: 0.770
|
|
pid_kd: 948.182
|
|
min_temp: 0
|
|
max_temp: 120
|
|
|
|
[fan]
|
|
pin: PA8
|
|
shutdown_speed: 0.0
|
|
|
|
[heater_fan hotend_cooling_fan]
|
|
pin: PE5
|
|
fan_speed: 1.0
|
|
heater: extruder
|
|
heater_temp: 50.0
|
|
|
|
[controller_fan controller_fan]
|
|
pin: PD12
|
|
fan_speed: 1.0
|
|
stepper: stepper_x, stepper_y, stepper_z
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 500
|
|
max_accel: 20000
|
|
max_z_velocity: 15
|
|
max_z_accel: 2000
|
|
|
|
[mcu]
|
|
serial: INSERTSERIALIDHERE
|
|
|
|
[board_pins octopus_11_tmc2209]
|
|
aliases:
|
|
## Expansion ports
|
|
# EXP1 header
|
|
EXP1_1=PE8, EXP1_3=PE9, EXP1_5=PE12, EXP1_7=PE14, EXP1_9=<GND>,
|
|
EXP1_2=PE7, EXP1_4=PE10, EXP1_6=PE13, EXP1_8=PE15, EXP1_10=<5V>,
|
|
# EXP2 header
|
|
EXP2_1=PA6, EXP2_3=PB1, EXP2_5=PB2, EXP2_7=PC15, EXP2_9=<GND>,
|
|
EXP2_2=PA5, EXP2_4=PA4, EXP2_6=PA7, EXP2_8=<RST>, EXP2_10=PC5,
|
|
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi2"
|