297 lines
5.7 KiB
INI
297 lines
5.7 KiB
INI
# This file contains common pin mappings for a Fysetc F6 board.
|
|
# To use this config, the firmware should be compiled for the AVR atmega2560.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PF0
|
|
dir_pin: PF1
|
|
enable_pin: !PD7
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: PK1 # PK2 for X-max
|
|
position_endstop: 0
|
|
position_max: 200
|
|
|
|
[stepper_y]
|
|
step_pin: PF6
|
|
dir_pin: PF7
|
|
enable_pin: !PF2
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: PJ1 # PJ0 for Y-max
|
|
position_endstop: 0
|
|
position_max: 200
|
|
|
|
[stepper_z]
|
|
step_pin: PL6
|
|
dir_pin: PL1
|
|
enable_pin: !PF4
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: PB6 # PE4 for Z-max
|
|
position_endstop: 0
|
|
position_max: 400
|
|
|
|
[extruder]
|
|
step_pin: PA4
|
|
dir_pin: !PA6
|
|
enable_pin: !PA2
|
|
microsteps: 16
|
|
rotation_distance: 33.500
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PE3
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PK4
|
|
control: pid
|
|
pid_Kp: 22
|
|
pid_Ki: 1.08
|
|
pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 260
|
|
|
|
#[extruder1]
|
|
#step_pin: PC1
|
|
#dir_pin: !PC3
|
|
#enable_pin: !PC7
|
|
#heater_pin: PH3
|
|
#sensor_pin: PK5
|
|
|
|
#[extruder2]
|
|
#step_pin: PF5
|
|
#dir_pin: !PF3
|
|
#enable_pin: !PG1
|
|
#heater_pin: PH4
|
|
#sensor_pin: PK6
|
|
|
|
[heater_bed]
|
|
heater_pin: PH5
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PK7
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
#fan for printed model FAN0
|
|
[fan]
|
|
pin: PL5
|
|
|
|
#fan for hotend FAN1
|
|
#[heater_fan my_nozzle_fan]
|
|
#pin: PL4
|
|
#shutdown_speed: 1
|
|
|
|
#fan for control board FAN2
|
|
#[heater_fan my_control_fan]
|
|
#pin: PL3
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
#Prevents communication issues with SPI drivers
|
|
[static_digital_output disable_sdcard]
|
|
pins: PB0
|
|
|
|
########################################
|
|
# TMC UART configuration
|
|
########################################
|
|
|
|
# For TMC UART
|
|
# 1) Remove all jumpers below the stepper drivers.
|
|
# 2) Place jumper on the left and middle pin of the three pin header.
|
|
|
|
#[tmc2208 stepper_x]
|
|
#uart_pin: PG3
|
|
#tx_pin: PJ2
|
|
#run_current: 0.8
|
|
#hold_current: 0.5
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2208 stepper_y]
|
|
#uart_pin: PJ3
|
|
#tx_pin: PJ4
|
|
#run_current: 0.8
|
|
#hold_current: 0.5
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2208 stepper_z]
|
|
#uart_pin: PE2
|
|
#tx_pin: PE6
|
|
#run_current: 0.8
|
|
#hold_current: 0.5
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2208 extruder]
|
|
#uart_pin: PJ5
|
|
#tx_pin: PJ6
|
|
#run_current: 0.8
|
|
#hold_current: 0.5
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2208 extruder1]
|
|
#uart_pin: PE7
|
|
#tx_pin: PD4
|
|
#run_current: 0.8
|
|
#hold_current: 0.5
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2208 extruder2]
|
|
#uart_pin: PA1
|
|
#tx_pin: PD5
|
|
#run_current: 0.8
|
|
#hold_current: 0.5
|
|
#stealthchop_threshold: 999999
|
|
|
|
########################################
|
|
# TMC SPI configuration
|
|
########################################
|
|
|
|
# For TMC SPI
|
|
# 1) Remove all jumpers below the stepper drivers.
|
|
# 2) Place jumper on the middle and right pin of the small three pin header.
|
|
# 3) Place jumpers on the four small two pin headers.
|
|
|
|
# For TMC Sensorless homing / DIAG1
|
|
# 1) Place jumper on the small two pin header near the endstop.
|
|
|
|
#[tmc2130 stepper_x]
|
|
#cs_pin: PG4
|
|
#diag1_pin: PK1
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2130 stepper_y]
|
|
#cs_pin: PG2
|
|
#diag1_pin: PJ1
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2130 stepper_z]
|
|
#cs_pin: PJ7
|
|
#diag1_pin: PB6
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2130 extruder]
|
|
#cs_pin: PL2
|
|
#diag1_pin: PE4
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2130 extruder1]
|
|
#cs_pin: PC5
|
|
#diag1_pin: PJ0
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 999999
|
|
|
|
#[tmc2130 extruder2]
|
|
#cs_pin: PL7
|
|
#diag1_pin: PK2
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 999999
|
|
|
|
########################################
|
|
# EXP1 / EXP2 (display) pins
|
|
########################################
|
|
|
|
# These must be turned 180° when compared to the default RAMPS layout.
|
|
# The aliases below are 180° turned from what Fysetc considers pin 1,
|
|
# but visually correspond to the plugs on the board.
|
|
|
|
[board_pins]
|
|
aliases:
|
|
# EXP1 header
|
|
EXP1_1=PC0, EXP1_2=PC2,
|
|
EXP1_3=PH0, EXP1_4=PH1,
|
|
EXP1_5=PA1, EXP1_6=PA3, # Slot in the socket on this side
|
|
EXP1_7=PA5, EXP1_8=PA7,
|
|
EXP1_9=<GND>, EXP1_10=<5V>,
|
|
|
|
# EXP2 header
|
|
EXP2_1=PB3, EXP2_2=PB1,
|
|
EXP2_3=PC6, EXP2_4=PB0,
|
|
EXP2_5=PC4, EXP2_6=PB2, # Slot in the socket on this side
|
|
EXP2_7=PL0, EXP2_8=<RST>,
|
|
EXP2_9=<GND>, EXP2_10=<5V> # or PG0 via jumper
|
|
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
|
|
|
########################################
|
|
# Servos
|
|
########################################
|
|
|
|
# All Servo pins support hardware PWM.
|
|
|
|
#[servo my_servo1]
|
|
#pin: PB7
|
|
|
|
#[servo my_servo2]
|
|
#pin: PB5
|
|
|
|
#[servo my_servo3]
|
|
#pin: PB4
|
|
|
|
#[servo my_servo4]
|
|
#pin: PG5
|
|
|
|
########################################
|
|
# RGB header
|
|
########################################
|
|
|
|
# All RGB pins support hardware PWM.
|
|
|
|
#[output_pin blue]
|
|
#pin: PH6
|
|
|
|
#[output_pin red]
|
|
#pin: PE5
|
|
|
|
#[output_pin green]
|
|
#pin: PG5
|
|
|
|
########################################
|
|
# AUX-1 header
|
|
########################################
|
|
|
|
# Various analog and digital pins
|
|
# PK0 (analog), PK3 (analog), <GND>, <5V>
|
|
# PE0 (RXD0) , PE1 (TXD0) , <GND>, <5V>
|
|
|
|
########################################
|
|
# SD header
|
|
########################################
|
|
|
|
# Various digital / SPI pins
|
|
# PL0 , PB2, PB0, RST
|
|
# <5V>, PB3, PB1, <GND>
|
|
|
|
########################################
|
|
# UART header
|
|
########################################
|
|
|
|
# Various digital / UART pins
|
|
# <5V>
|
|
# <GND>
|
|
# PD2
|
|
# PD3
|
|
|
|
########################################
|
|
# I2C header
|
|
########################################
|
|
|
|
# SCL, SDA, <5V>, <GND>
|