132 lines
2.6 KiB
INI
132 lines
2.6 KiB
INI
# This file contains common pin mappings for the TH3D EZBoard Lite v2.
|
|
# To use this config, check "Enable extra low-level configuration options"
|
|
# and compile the firmware for the STM32F405 with 12mhz Crystal,
|
|
# 48KiB Bootloader, and USB communication.
|
|
|
|
# After the firmware is compiled, execute the following command
|
|
# arm-none-eabi-objcopy -O srec out/klipper.elf out/firmware.bin
|
|
|
|
# The "make flash" command does not work on this board. Instead,
|
|
# after running "make", copy the generated "out/firmware.bin" file to
|
|
# an SD card and then restart the board with that SD card.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-Klipper_stm32f407xx_0000000000000000-if00
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
[stepper_x]
|
|
step_pin: PB3
|
|
dir_pin: PD2
|
|
enable_pin: !PB5
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^!PC1
|
|
position_endstop: 0
|
|
position_max: 235
|
|
homing_speed: 50
|
|
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PC11
|
|
tx_pin: PC10
|
|
run_current: 0.600
|
|
uart_address: 0
|
|
|
|
[stepper_y]
|
|
step_pin: PB8
|
|
dir_pin: PC13
|
|
enable_pin: !PC12
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^!PC2
|
|
position_endstop: 0
|
|
position_max: 235
|
|
homing_speed: 50
|
|
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PC11
|
|
tx_pin: PC10
|
|
run_current: 0.600
|
|
uart_address: 1
|
|
|
|
[stepper_z]
|
|
step_pin: PA3
|
|
dir_pin: PB1
|
|
enable_pin: !PC14
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: ^!PC3
|
|
position_endstop: 0.5
|
|
position_max: 250
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PC11
|
|
tx_pin: PC10
|
|
run_current: 0.700
|
|
uart_address: 2
|
|
|
|
[extruder]
|
|
step_pin: PA15
|
|
dir_pin: PB11
|
|
enable_pin: !PB2
|
|
microsteps: 16
|
|
rotation_distance: 34.406
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PC8
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PA1
|
|
control: pid
|
|
pid_Kp: 22.2
|
|
pid_Ki: 1.08
|
|
pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: PC11
|
|
tx_pin: PC10
|
|
run_current: 0.800
|
|
stealthchop_threshold: 999999
|
|
uart_address: 3
|
|
|
|
[heater_bed]
|
|
heater_pin: PC9
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PA0
|
|
control: pid
|
|
pid_Kp: 54.027
|
|
pid_Ki: 0.770
|
|
pid_Kd: 948.182
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[fan]
|
|
pin: PC6
|
|
|
|
#[bltouch]
|
|
#sensor_pin: ^PC3
|
|
#control_pin: PA2
|
|
|
|
#[filament_switch_sensor my_sensor]
|
|
#switch_pin: PC0
|
|
|
|
########################################
|
|
# EXP1 / EXP2 (display) pins
|
|
########################################
|
|
|
|
[board_pins]
|
|
aliases:
|
|
# EXP1 header
|
|
EXP1_1=PA14, EXP1_3=PC4, EXP1_5=PC5, EXP1_7=PB12, EXP1_9=<GND>,
|
|
EXP1_2=PB0, EXP1_4=<RST>, EXP1_6=PB13, EXP1_8=PB15, EXP1_10=<5V>
|
|
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|