106 lines
2.0 KiB
INI
106 lines
2.0 KiB
INI
# This file contains common pin mappings for RAMBo boards. To use this
|
|
# config, the firmware should be compiled for the AVR atmega2560.
|
|
|
|
# See the example.cfg file for a description of available parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PC0
|
|
dir_pin: PL1
|
|
enable_pin: !PA7
|
|
step_distance: .0125
|
|
endstop_pin: ^PB6
|
|
#endstop_pin: ^PA2
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: PC1
|
|
dir_pin: !PL0
|
|
enable_pin: !PA6
|
|
step_distance: .0125
|
|
endstop_pin: ^PB5
|
|
#endstop_pin: ^PA1
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: PC2
|
|
dir_pin: PL2
|
|
enable_pin: !PA5
|
|
step_distance: 0.00025
|
|
endstop_pin: ^PB4
|
|
#endstop_pin: ^PC7
|
|
position_endstop: 0.5
|
|
position_max: 200
|
|
|
|
[extruder]
|
|
step_pin: PC3
|
|
dir_pin: PL6
|
|
enable_pin: !PA4
|
|
step_distance: .002
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PH6
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PF0
|
|
control: pid
|
|
pid_Kp: 22.2
|
|
pid_Ki: 1.08
|
|
pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
#[extruder1]
|
|
#step_pin: PC4
|
|
#dir_pin: PL7
|
|
#enable_pin: !PA3
|
|
#heater_pin: PH4
|
|
#sensor_pin: PF1
|
|
#...
|
|
|
|
[heater_bed]
|
|
heater_pin: PE5
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PF2
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[fan]
|
|
pin: PH5
|
|
|
|
#[heater_fan nozzle_cooling_fan]
|
|
#pin: PH3
|
|
|
|
[mcu]
|
|
serial: /dev/ttyACM0
|
|
custom:
|
|
# Turn off yellow led
|
|
set_digital_out pin=PB7 value=0
|
|
# Stepper micro-step pins
|
|
set_digital_out pin=PG1 value=1
|
|
set_digital_out pin=PG0 value=1
|
|
set_digital_out pin=PK7 value=1
|
|
set_digital_out pin=PG2 value=1
|
|
set_digital_out pin=PK6 value=1
|
|
set_digital_out pin=PK5 value=1
|
|
set_digital_out pin=PK3 value=1
|
|
set_digital_out pin=PK4 value=1
|
|
#set_digital_out pin=PK2 value=1
|
|
#set_digital_out pin=PK1 value=1
|
|
# Initialize digipot
|
|
send_spi_message pin=PD7 msg=0487 # X = ~0.75A
|
|
send_spi_message pin=PD7 msg=0587 # Y = ~0.75A
|
|
send_spi_message pin=PD7 msg=0387 # Z = ~0.75A
|
|
send_spi_message pin=PD7 msg=00A5 # E0
|
|
send_spi_message pin=PD7 msg=017D # E1
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|