| .. |
|
atsam
|
atsam: Use enumerations for pin mappings
|
2019-03-17 19:38:18 -04:00 |
|
atsamd
|
atsamd: Use enumerations for pin mappings
|
2019-03-17 19:38:18 -04:00 |
|
avr
|
avr: Use enumerations for pin mappings
|
2019-03-17 19:38:18 -04:00 |
|
generic
|
command: Always pass a string to the DECL_CONSTANT() macro
|
2019-03-17 19:38:18 -04:00 |
|
linux
|
linux: Use enumerations for pin mappings
|
2019-03-17 19:38:18 -04:00 |
|
lpc176x
|
lpc176x: Use enumerations for pin mappings
|
2019-03-17 19:38:18 -04:00 |
|
pru
|
pru: Use enumerations for pin mappings
|
2019-03-17 19:38:18 -04:00 |
|
simulator
|
simulator: Wrap code to 80 columns
|
2019-02-27 14:20:15 -05:00 |
|
stm32f1
|
stm32f1: Use enumerations for pin mappings
|
2019-03-17 19:38:18 -04:00 |
|
Kconfig
|
initial_pins: Add ability to configure output pins at mcu startup
|
2019-03-17 20:56:25 -04:00 |
|
Makefile
|
initial_pins: Add ability to configure output pins at mcu startup
|
2019-03-17 20:56:25 -04:00 |
|
adccmds.c
|
adccmds: Run gpio_adc_setup() before oid_alloc()
|
2019-01-13 11:03:30 -05:00 |
|
basecmd.c
|
command: Always pass a string to the DECL_CONSTANT() macro
|
2019-03-17 19:38:18 -04:00 |
|
basecmd.h
|
pru: Support config_reset command to manually reset mcu
|
2017-09-03 23:16:38 -04:00 |
|
buttons.c
|
buttons: Wrap code to 80 columns
|
2019-02-27 14:20:15 -05:00 |
|
byteorder.h
|
byteorder: Add a header file defining common byteswap functions
|
2018-05-21 09:44:40 -04:00 |
|
command.c
|
command: Wait to send ack until after processing commands
|
2018-05-28 10:43:40 -04:00 |
|
command.h
|
msgproto: Convert static strings to a more generic enumeration system
|
2019-03-17 19:38:18 -04:00 |
|
compiler.h
|
compiler.h: Check if __aligned and __section macros are already defined
|
2016-06-13 23:18:59 -04:00 |
|
ctr.h
|
command: Support evaluating C expressions in DECL_CONSTANT()
|
2019-03-17 19:38:18 -04:00 |
|
debugcmds.c
|
debugcmds: Add support for reading/writing 32bit values
|
2019-02-07 11:50:14 -05:00 |
|
endstop.c
|
endstop: Eliminate end_stop_set_oversample command
|
2017-10-12 11:59:27 -04:00 |
|
gpiocmds.c
|
command: Always pass a string to the DECL_CONSTANT() macro
|
2019-03-17 19:38:18 -04:00 |
|
i2ccmds.c
|
i2ccmds: Pass the i2c address as a 7-bit number (0-127)
|
2019-01-07 20:00:44 -05:00 |
|
initial_pins.c
|
initial_pins: Add ability to configure output pins at mcu startup
|
2019-03-17 20:56:25 -04:00 |
|
initial_pins.h
|
initial_pins: Add ability to configure output pins at mcu startup
|
2019-03-17 20:56:25 -04:00 |
|
lcd_hd44780.c
|
lcd_hd44780: Add micro-controller code for the HD44780 LCD chip
|
2018-03-06 11:30:34 -05:00 |
|
lcd_st7920.c
|
lcd_st7920: Use a longer delay at the start of each command/data
|
2018-06-22 23:47:09 -04:00 |
|
pwmcmds.c
|
pwmcmds: Wrap code to 80 columns
|
2019-02-27 14:20:15 -05:00 |
|
sched.c
|
sched: Force sched_try_shutdown to be inlined
|
2018-10-13 11:47:00 -04:00 |
|
sched.h
|
pru: Support config_reset command to manually reset mcu
|
2017-09-03 23:16:38 -04:00 |
|
spi_software.c
|
spi_software: Implementation of software spi
|
2019-02-13 11:52:20 -05:00 |
|
spi_software.h
|
spi_software: Implementation of software spi
|
2019-02-13 11:52:20 -05:00 |
|
spicmds.c
|
spicmds: Wrap code to 80 columns
|
2019-02-27 14:20:15 -05:00 |
|
spicmds.h
|
thermocouple: Add initial support for common SPI temperature sensing chips
|
2018-07-24 11:16:05 -04:00 |
|
stepper.c
|
command: Always pass a string to the DECL_CONSTANT() macro
|
2019-03-17 19:38:18 -04:00 |
|
stepper.h
|
stepper: Introduce stepper_get_position command and remove from endstop.c
|
2017-03-09 14:54:52 -05:00 |
|
thermocouple.c
|
thermocouple: Define thermocouple types using enumerations
|
2019-03-17 19:38:18 -04:00 |
|
tmcuart.c
|
pins: Add support for pull down resistors
|
2019-02-27 11:13:21 -05:00 |
4a35f927fc