173 lines
5.8 KiB
INI
173 lines
5.8 KiB
INI
# This file serves as documentation for config parameters. One may
|
|
# copy and edit this file to configure a new printer.
|
|
|
|
# DO NOT COPY THIS FILE WITHOUT CAREFULLY READING AND UPDATING IT
|
|
# FIRST. Incorrectly configured parameters may cause damage.
|
|
|
|
# A note on pin names: pins may be configured with a hardware name
|
|
# (such as PA4) or with a board name (such as ar29). In order to use a
|
|
# board name, the pin_map variable in the mcu section must specify
|
|
# which board definition to use. (See the klippy/pins.py file for the
|
|
# available pin and board names.)
|
|
# Pin names may be preceded by an '!' to indicate that a reverse
|
|
# polarity should be used (eg, trigger on low instead of high). Input
|
|
# pins may be prceded by an '^' to indicate that a hardware pull-up
|
|
# resistor should be enabled for the pin.
|
|
|
|
|
|
# The stepper_x section is used to describe the stepper controlling
|
|
# the X axis in a cartesian robot
|
|
[stepper_x]
|
|
step_pin: ar29
|
|
# Step GPIO pin (triggered high)
|
|
dir_pin: ar28
|
|
# Direction GPIO pin (low indicates positive direction)
|
|
enable_pin: !ar25
|
|
# Enable pin (default is enable high; use ! to indicate enable low)
|
|
step_distance: .0225
|
|
# Distance in mm that each step causes the axis to travel
|
|
max_velocity: 500
|
|
# Maximum velocity (in mm/s) of the stepper
|
|
max_accel: 3000
|
|
# Maximum acceleration (in mm/s^2) of the stepper
|
|
endstop_pin: ^ar0
|
|
# Endstop switch detection pin
|
|
homing_speed: 50.0
|
|
# Maximum velocity (in mm/s) of the stepper when homing
|
|
homing_retract_dist: 5.0
|
|
# Distance to backoff (in mm) before homing a second time during homing
|
|
homing_positive_dir: False
|
|
# If true, homes in a positive direction (away from zero)
|
|
position_min: -0.25
|
|
# Minimum valid distance (in mm) the user may command the stepper to
|
|
# move to (not currently enforced)
|
|
position_endstop: 0
|
|
# Location of the endstop (in mm)
|
|
position_max: 200
|
|
# Maximum valid distance (in mm) the user may command the stepper to
|
|
# move to (not currently enforced)
|
|
|
|
# The stepper_y section is used to describe the stepper controlling
|
|
# the Y axis in a cartesian robot. It has the same settings as the
|
|
# stepper_x section
|
|
[stepper_y]
|
|
step_pin: ar27
|
|
dir_pin: ar26
|
|
enable_pin: !ar25
|
|
step_distance: .0225
|
|
max_velocity: 500
|
|
max_accel: 3000
|
|
endstop_pin: ^ar1
|
|
position_min: -0.25
|
|
position_endstop: 0
|
|
position_max: 200
|
|
|
|
# The stepper_z section is used to describe the stepper controlling
|
|
# the Z axis in a cartesian robot. It has the same settings as the
|
|
# stepper_x section
|
|
[stepper_z]
|
|
step_pin: ar23
|
|
dir_pin: ar22
|
|
enable_pin: !ar25
|
|
step_distance: .005
|
|
max_velocity: 250
|
|
max_accel: 30
|
|
endstop_pin: ^ar2
|
|
position_min: 0.1
|
|
position_endstop: 0.5
|
|
position_max: 200
|
|
|
|
# The extruder section is used to describe both the stepper
|
|
# controlling the printer extruder and the heater parameters for the
|
|
# nozzle. The stepper configuration has the same settings as the
|
|
# stepper_x section and the heater configuration has the same settings
|
|
# as the heater_bed section
|
|
[extruder]
|
|
step_pin: ar19
|
|
dir_pin: ar18
|
|
enable_pin: !ar25
|
|
step_distance: .004242
|
|
max_velocity: 200000
|
|
max_accel: 3000
|
|
# The remaining variables describe the extruder heater
|
|
heater_pin: ar4
|
|
# PWM output pin controlling the heater
|
|
thermistor_pin: analog1
|
|
# Analog input pin connected to thermistor
|
|
thermistor_type: EPCOS 100K B57560G104F
|
|
# Type of thermistor (see klippy/heater.py for available types)
|
|
pullup_resistor: 4700
|
|
# The resistance (in ohms) of the pullup attached to the thermistor
|
|
control: pid
|
|
# Control algorithm (either pid or watermark)
|
|
pid_Kp: 22.2
|
|
# Kp is the "proportional" constant for the pid
|
|
pid_Ki: 1.08
|
|
# Ki is the "integral" constant for the pid
|
|
pid_Kd: 114
|
|
# Kd is the "derivative" constant for the pid
|
|
pid_deriv_time: 2.0
|
|
# A time value (in seconds) over which the derivative in the pid
|
|
# will be smoothed to reduce the impact of measurement noise
|
|
pid_integral_max: 255
|
|
# The maximum "windup" the integral term may accumulate
|
|
min_temp: 0
|
|
# Minimum temperature in Celsius (mcu will shutdown if not met)
|
|
max_temp: 210
|
|
# Maximum temperature (mcu will shutdown if temperature is above
|
|
# this value)
|
|
|
|
# The heater_bed section describes a heated bed (if present - omit
|
|
# section if not present).
|
|
[heater_bed]
|
|
heater_pin: ar3
|
|
thermistor_pin: analog0
|
|
thermistor_type: EPCOS 100K B57560G104F
|
|
control: watermark
|
|
max_delta: 2.0
|
|
# The number of degrees in Celsius above the target temperature
|
|
# before disabling the heater as well as the number of degrees below
|
|
# the target before re-enabling the heater.
|
|
min_temp: 0
|
|
max_temp: 110
|
|
|
|
# Extruder print fan (omit section if fan not present)
|
|
[fan]
|
|
pin: ar14
|
|
# PWM output pin controlling the heater
|
|
hard_pwm: 1
|
|
# Set this value to force hardware PWM instead of software PWM. Set
|
|
# to 1 to force a hardware PWM at the fastest rate; set to a higher
|
|
# number (eg, 1024) to force hardware PWM with the given cycle time
|
|
# in clock ticks.
|
|
kick_start_time: 0.100
|
|
# Time (in seconds) to run the fan at full speed when first enabling
|
|
# it (helps get the fan spinning)
|
|
|
|
# Micro-controller information
|
|
[mcu]
|
|
serial: /dev/ttyACM0
|
|
# The serial port to connect to the MCU
|
|
baud: 115200
|
|
# The baud rate to use
|
|
pin_map: arduino
|
|
# This option may be used to add board specific pin name aliases
|
|
custom:
|
|
# This option may be used to specify a set of custom
|
|
# micro-controller commands to be sent at the start of the
|
|
# connection. It may be used to configure the initial settings of
|
|
# LEDs, to configure micro-stepping pins, to configure a digipot,
|
|
# etc.
|
|
|
|
# The printer section controls high level printer settings
|
|
[printer]
|
|
kinematics: cartesian
|
|
# This option must currently always be "cartesian"
|
|
motor_off_time: 60
|
|
# Time (in seconds) of idle time before the printer will try to
|
|
# disable active motors.
|
|
junction_deviation: 0.02
|
|
# Distance (in mm) used to control the internal approximated
|
|
# centripetal velocity cornering algorithm. A larger number will
|
|
# permit higher "cornering speeds" at the junction of two moves.
|