.. |
avr
|
avr: Disable usb serial interrupts while processing data
|
2018-10-02 22:17:39 -04:00 |
generic
|
armcm_irq: Fix jump target alignment
|
2018-10-13 11:47:00 -04:00 |
linux
|
linux: Add support for bi-directional SPI communication
|
2018-07-24 11:16:05 -04:00 |
lpc176x
|
lpc176x: Divide system clock within timer; not on system bus
|
2018-10-18 09:37:47 -04:00 |
pru
|
pru: Add wrappers for gpio_x_reset()
|
2018-08-27 12:45:01 -04:00 |
sam3x8e
|
sam3x8e: Don't report an error if bossac errors during device restart
|
2018-10-22 17:41:29 -04:00 |
sam4e8e
|
Implement I2C support in the SAM4E8E port
|
2018-10-27 10:34:28 -04:00 |
samd21
|
usb_cdc: Add usb_read_ep0_setup() interface function
|
2018-09-30 22:32:19 -04:00 |
simulator
|
simulator: Add support for gpio_x_reset()
|
2018-08-27 12:45:01 -04:00 |
stm32f1
|
stm32f1: Use __always_inline on timer_read_time
|
2018-10-11 22:20:02 -04:00 |
Kconfig
|
Add generic i2c interface
|
2018-10-27 10:34:28 -04:00 |
Makefile
|
Add generic i2c interface
|
2018-10-27 10:34:28 -04:00 |
adccmds.c
|
adccmds: Add support for min/max temperature check filtering
|
2018-07-02 13:56:34 -04:00 |
basecmd.c
|
basecmd: Rename get_status to get_clock
|
2018-05-29 10:57:29 -04:00 |
basecmd.h
|
pru: Support config_reset command to manually reset mcu
|
2017-09-03 23:16:38 -04:00 |
buttons.c
|
buttons: Clear pressed/last_pressed state on new buttons_query command
|
2018-10-01 12:40:28 -04:00 |
byteorder.h
|
byteorder: Add a header file defining common byteswap functions
|
2018-05-21 09:44:40 -04:00 |
command.c
|
command: Wait to send ack until after processing commands
|
2018-05-28 10:43:40 -04:00 |
command.h
|
command: Wait to send ack until after processing commands
|
2018-05-28 10:43:40 -04:00 |
compiler.h
|
compiler.h: Check if __aligned and __section macros are already defined
|
2016-06-13 23:18:59 -04:00 |
ctr.h
|
build: Avoid linker magic in compile_time_request.c unique id generation
|
2017-05-26 12:32:02 -04:00 |
debugcmds.c
|
debugcmds: Move debugging commands from basecmd.c to new file
|
2017-05-15 14:02:59 -04:00 |
endstop.c
|
endstop: Eliminate end_stop_set_oversample command
|
2017-10-12 11:59:27 -04:00 |
gpiocmds.c
|
gpiocmds: Add update_digital_out command
|
2018-06-27 12:10:39 -04:00 |
i2ccmds.c
|
Add generic i2c interface
|
2018-10-27 10:34:28 -04:00 |
lcd_hd44780.c
|
lcd_hd44780: Add micro-controller code for the HD44780 LCD chip
|
2018-03-06 11:30:34 -05:00 |
lcd_st7920.c
|
lcd_st7920: Use a longer delay at the start of each command/data
|
2018-06-22 23:47:09 -04:00 |
pwmcmds.c
|
gpiocmds: Allow the start value for a pin to differ from the default_value
|
2017-10-12 11:59:27 -04:00 |
sched.c
|
sched: Force sched_try_shutdown to be inlined
|
2018-10-13 11:47:00 -04:00 |
sched.h
|
pru: Support config_reset command to manually reset mcu
|
2017-09-03 23:16:38 -04:00 |
spicmds.c
|
thermocouple: Add initial support for common SPI temperature sensing chips
|
2018-07-24 11:16:05 -04:00 |
spicmds.h
|
thermocouple: Add initial support for common SPI temperature sensing chips
|
2018-07-24 11:16:05 -04:00 |
stepper.c
|
stepper: Introduce and use gpio_out_toggle_noirq()
|
2018-05-15 17:09:11 -04:00 |
stepper.h
|
stepper: Introduce stepper_get_position command and remove from endstop.c
|
2017-03-09 14:54:52 -05:00 |
thermocouple.c
|
thermocouple: Minor fixes
|
2018-07-25 09:06:50 -04:00 |
tmcuart.c
|
tmc2208: Initial support for configuring TMC2208 drivers
|
2018-08-27 12:51:27 -04:00 |