163 lines
3.3 KiB
INI
163 lines
3.3 KiB
INI
# This file contains common pin mappings for the 2020 Creality CR-10
|
|
# V3. The mainboard is a Creality 3D v2.5.2 (8-bit mainboard with
|
|
# ATMega2560). To use this config, the firmware should be compiled for
|
|
# the AVR atmega2560.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
# For better compatibility with GCodes generated for Marlin, you
|
|
# may wish to add the following section, if you have BLTouch:
|
|
#[gcode_macro G29]
|
|
#gcode:
|
|
# BED_MESH_CALIBRATE
|
|
|
|
[stepper_x]
|
|
step_pin: PF0 #ar54
|
|
dir_pin: PF1 #ar55
|
|
enable_pin: !PD7 #!ar38
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^PE5 #^ar3
|
|
position_endstop: 0
|
|
position_max: 300
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: PF6 #ar60
|
|
dir_pin: PF7 #ar61
|
|
enable_pin: !PF2 #!ar56
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^PJ1 #^ar14
|
|
position_endstop: 0
|
|
position_max: 300
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: PL3 #ar46
|
|
dir_pin: !PL1 #!ar48
|
|
enable_pin: !PK0 #!ar62
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
position_max: 400
|
|
#Uncomment if you have a BL-Touch:
|
|
#position_min: -4
|
|
#endstop_pin: probe:z_virtual_endstop
|
|
#and comment the follwing lines:
|
|
position_endstop: 0.0
|
|
endstop_pin: ^PD3 #ar18
|
|
|
|
[safe_z_home]
|
|
home_xy_position: 104.25,147.6
|
|
speed: 80
|
|
z_hop: 10
|
|
z_hop_speed: 10
|
|
|
|
[extruder]
|
|
step_pin: PA4 # ar26
|
|
dir_pin: !PA6 # !ar28
|
|
enable_pin: !PA2 # !ar24
|
|
microsteps: 16
|
|
rotation_distance: 7.7201944 # 16 microsteps * 200 steps/rotation / steps/mm
|
|
#Correction formula is new_rotation_distance = old_rotation_distance * mmsExtracted / 100.0
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PB4 #ar10
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PK5 #analog13
|
|
control: pid
|
|
pid_kp: 22.107
|
|
pid_ki: 1.170
|
|
pid_kd: 104.458
|
|
min_temp: 0
|
|
max_temp: 255
|
|
|
|
[heater_bed]
|
|
heater_pin: PH5 #ar8
|
|
sensor_type: ATC Semitec 104GT-2
|
|
sensor_pin: PK6 #analog14
|
|
control: pid
|
|
#Stock PID configuration taken from Marlin
|
|
pid_Kp: 201.86
|
|
pid_Ki: 10.67
|
|
pid_Kd: 954.96
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[fan]
|
|
pin: PH6 #ar9
|
|
|
|
[mcu]
|
|
serial: /dev/ttyUSB0
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
[display]
|
|
lcd_type: st7920
|
|
cs_pin: PH1 #ar16
|
|
sclk_pin: PA1 #ar23
|
|
sid_pin: PH0 #ar17
|
|
encoder_pins: ^PC4, ^PC6 #^ar33, ^ar31
|
|
click_pin: ^!PC2 #^!ar35
|
|
|
|
|
|
#Uncomment the following lines if you have a BL-Touch
|
|
#[bltouch]
|
|
#sensor_pin: ^PD2 #^ar19
|
|
#control_pin: PB5 #ar11
|
|
#set_output_mode: 5V
|
|
#pin_move_time: 0.4
|
|
#stow_on_each_sample: False
|
|
#probe_with_touch_mode: False
|
|
#x_offset: 45.75
|
|
#y_offset: -3.40
|
|
#z_offset: 3.28
|
|
#samples: 2
|
|
#sample_retract_dist: 2
|
|
#samples_result: average
|
|
|
|
#Uncomment the following lines if you have a BL-Touch
|
|
#[bed_mesh]
|
|
#speed: 50
|
|
#horizontal_move_z: 6
|
|
#mesh_min: 46.50,0.75
|
|
#mesh_max: 253.5,295.85
|
|
#probe_count: 7,7
|
|
#algorithm: bicubic
|
|
|
|
[pause_resume]
|
|
recover_velocity: 50
|
|
|
|
[filament_switch_sensor fil_runout_sensor]
|
|
pause_on_runout: True
|
|
switch_pin: PE4 #ar2
|
|
|
|
[bed_screws]
|
|
screw1: 33,29
|
|
screw1_name: front left screw
|
|
screw2: 273,29
|
|
screw2_name: front right screw
|
|
screw3: 273,269
|
|
screw3_name: rear right screw
|
|
screw4: 33,269
|
|
screw4_name: rear left screw
|
|
|
|
#Uncomment the following lines if you have a BL-Touch
|
|
#[screws_tilt_adjust]
|
|
#screw1: 0,29
|
|
#screw1_name: front left screw
|
|
#screw2: 228,29
|
|
#screw2_name: front right screw
|
|
#screw3: 228,269
|
|
#screw3_name: rear right screw
|
|
#screw4: 0,269
|
|
#screw4_name: rear left screw
|
|
#speed: 50
|
|
#horizontal_move_z: 10
|
|
#screw_thread: CW-M3
|