| .. |
|
Kconfig
|
stm32: Allow selecting bootloader size for STM32F446
|
2021-05-03 14:36:18 -04:00 |
|
Makefile
|
stm32: Add hardware PWM support for STM32F1
|
2021-03-26 12:04:51 -04:00 |
|
adc.c
|
stm32: Added mcu temperature support additional mcu (#4211)
|
2021-04-25 10:35:15 -04:00 |
|
can.c
|
stm32: CAN Kconfig typo
|
2021-04-07 13:06:13 -04:00 |
|
chipid.c
|
stm32: Enable chipid as usb serial number
|
2019-11-25 19:30:31 -05:00 |
|
gpio.c
|
stm32: Define PGx pins on stm32f103
|
2019-11-02 11:35:27 -04:00 |
|
gpio.h
|
stm32: Add hardware PWM support for STM32F1
|
2021-03-26 12:04:51 -04:00 |
|
hard_pwm.c
|
stm32: Add hardware PWM support for STM32F1
|
2021-03-26 12:04:51 -04:00 |
|
i2c.c
|
stm32: Add support for STM32F1 I2C1 alternate pin mapping (#4012)
|
2021-03-02 23:02:20 -05:00 |
|
internal.h
|
stm32: Initial support for stm32f2 (#3001)
|
2020-06-23 10:52:15 -04:00 |
|
serial.c
|
stm32: Simplify USB/Serial/CANbus Kconfig selection
|
2021-03-18 13:33:33 -04:00 |
|
spi.c
|
stm32: Add support for spi bus on stm32f407 pins PI2,PI3,PI1
|
2021-02-12 17:32:54 -05:00 |
|
stm32f0.c
|
stm32: Simplify USB/Serial/CANbus Kconfig selection
|
2021-03-18 13:33:33 -04:00 |
|
stm32f0_adc.c
|
stm32: Support reading chip based temperature sensor on stm32f0
|
2020-10-29 11:55:06 -04:00 |
|
stm32f0_i2c.c
|
stm32f0: Initial support for i2c on stm32f0
|
2019-11-14 15:54:28 -05:00 |
|
stm32f0_serial.c
|
stm32: Simplify USB/Serial/CANbus Kconfig selection
|
2021-03-18 13:33:33 -04:00 |
|
stm32f0_timer.c
|
stm32: Initial support for stm32f070
|
2019-10-23 21:19:03 -04:00 |
|
stm32f1.c
|
stm32f1: reset peripherals in enable_pcclock()
|
2021-04-07 12:57:21 -04:00 |
|
stm32f4.c
|
stm32: Optimize stm32f401 peripheral clock
|
2021-02-19 12:19:32 -05:00 |
|
usbfs.c
|
stm32: Initial support for stm32f070
|
2019-10-23 21:19:03 -04:00 |
|
usbotg.c
|
stm32: Wait for setup complete to enable ep0 rx in usbotg.c
|
2020-05-03 12:00:47 -04:00 |
|
watchdog.c
|
…
|
|
1fb091c4fa