..
atsam
atsam: Support reading chip based temperature sensor on sam4e
2020-10-29 11:55:06 -04:00
atsamd
atsamd: Support reading chip based temperature sensor
2020-10-29 11:55:06 -04:00
avr
Kconfig: Add a new CONFIG_HAVE_STRICT_TIMING build definition
2020-05-31 14:57:06 -04:00
generic
command: Fix handling of buffer passing in args[] on 64bit mcu
2020-10-30 14:04:12 -04:00
linux
pca9685: Use move queue for pwm updates
2020-12-04 16:10:13 -05:00
lpc176x
lpc176x: Fix spi mode bits
2020-07-10 16:08:18 -04:00
pru
pru: Disable gpio mux configuration code
2020-12-04 16:10:13 -05:00
simulator
command: Fix handling of buffer passing in args[] on 64bit mcu
2020-10-30 14:04:12 -04:00
stm32
stm32: Only use the HSI48 clock when doing "usb clock recovery"
2020-12-08 09:00:47 -05:00
Kconfig
Kconfig: Only show the "usb ids" menu if low-level options are enabled
2020-05-31 21:05:04 -04:00
Makefile
adxl345: Add support for adxl345 accelerometer
2020-09-05 09:11:04 -04:00
adccmds.c
adccmds: Run gpio_adc_setup() before oid_alloc()
2019-01-13 11:03:30 -05:00
basecmd.c
stepper: Use a reusable interface to the "move queue"
2020-12-04 16:10:13 -05:00
basecmd.h
stepper: Use a reusable interface to the "move queue"
2020-12-04 16:10:13 -05:00
buttons.c
buttons: initialize mcu buttons based on inverted state
2019-07-05 20:01:07 -04:00
byteorder.h
…
command.c
command: Fix handling of buffer passing in args[] on 64bit mcu
2020-10-30 14:04:12 -04:00
command.h
command: Add command_decode_ptr() helper
2020-10-30 14:04:08 -04:00
compiler.h
…
ctr.h
ctr: Encode negative integers in normal hex notation
2019-08-22 13:06:44 -04:00
debugcmds.c
command: Add command_decode_ptr() helper
2020-10-30 14:04:08 -04:00
endstop.c
endstop: Rename mcu end_stop commands to endstop
2019-07-12 08:10:53 -04:00
gpiocmds.c
gpiocmds: Use move queue for software pwm
2020-12-04 16:10:13 -05:00
i2ccmds.c
command: Add command_decode_ptr() helper
2020-10-30 14:04:08 -04:00
initial_pins.c
initial_pins: Add ability to configure output pins at mcu startup
2019-03-17 20:56:25 -04:00
initial_pins.h
initial_pins: Add ability to configure output pins at mcu startup
2019-03-17 20:56:25 -04:00
lcd_hd44780.c
command: Add command_decode_ptr() helper
2020-10-30 14:04:08 -04:00
lcd_st7920.c
command: Add command_decode_ptr() helper
2020-10-30 14:04:08 -04:00
neopixel.c
neopixel: Fix neopixel_result message so that it contains an oid
2020-11-05 11:40:34 -05:00
pwmcmds.c
pwmcmds: Use move queue for hard PWM
2020-12-04 16:10:13 -05:00
sched.c
sched: Force sched_try_shutdown to be inlined
2018-10-13 11:47:00 -04:00
sched.h
…
sensor_adxl345.c
sensor_adxl345: Remove unused stop_time parameter
2020-09-05 09:18:59 -04:00
spi_software.c
spi_software: Remove unused include file
2019-08-17 13:49:03 -04:00
spi_software.h
spi_software: Implementation of software spi
2019-02-13 11:52:20 -05:00
spicmds.c
command: Add command_decode_ptr() helper
2020-10-30 14:04:08 -04:00
spicmds.h
spicmds: Rework spi config commands
2019-08-06 18:56:53 -04:00
stepper.c
stepper: Use a reusable interface to the "move queue"
2020-12-04 16:10:13 -05:00
stepper.h
…
thermocouple.c
thermocouple: Define thermocouple types using enumerations
2019-03-17 19:38:18 -04:00
tmcuart.c
command: Add command_decode_ptr() helper
2020-10-30 14:04:08 -04:00
39a04eac5f